DOWNLOAD Sony XR-C7500R / XR-C7500RX Service Manual ↓ Size: 4.72 MB | Pages: 52 in PDF or view online for FREE

13

shaft A

shaft B

shaft C

1

Fit the lever (LDG-A) on
shafts A – C and install it.

shaft A

shaft B

2

Fit the lever (LDG-B) on  
shafts A and B and 
install it.

3

5

6

2

2

4

3

1

14

2

1

×

15

1. Clean the following parts with a denatured-alcohol-moistened

swab:

playback head

pinch roller

rubber belt

capstan

idler

2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the

parts adjusted.

5. The adjustments should be performed with the power supply

voltage unless otherwise noted.

Mode

Torque Meter

Meter Reading

 2.95 – 6.37 mN•m

Forward

CQ-102C

(30 – 65 g•cm)

(0.42 – 0.90 oz•inch)

Forward

0.05 – 0.44 mN•m

CQ-102C

(0.5 – 4.5g•cm)

Back Tension

(0.01 – 0.06 oz•inch)

2.95 – 6.37 mN•m

Reverse

CQ-102RC

(30 – 65 g•cm)

(0.42 – 0.90 oz•inch)

Reverse

0.05 – 0.44 mN•m

CQ-102RC

(0.5 – 4.5g•cm)

Back Tension

(0.01 – 0.06 oz•inch)

5.89 – 19.61 mN•m

FF, REW

CQ-201B

(60 – 200 g•cm)

(0.83 – 2.78 oz•inch)

Mode

Tension Meter

Meter Reading

more than 8.83 mN•m

Forward

CQ-403A

(more than 90 g)

(more than 3.18 oz)

more than 8.83 mN•m

Reverse

CQ-403R

(more than 90 g)

(more than 3.18 oz)

This set has the test mode function.

<Set the Test Mode>
1. Turn ON the regulated power supply. (The clock is displayed)

 Press the 

[OFF]

 button, if the clock is not displayed.

2. Press the preset 

[4]

 button.

3. Press the preset 

[5]

 button.

4. Press the preset 

[1]

 button for more than two seconds.

5. Then the display indicates all lights, the test mode is set.

<Release the Test mode>
1. Press the 

[OFF]

 button.

16

– SET  UPPER  VIEW –

– SET  BOTTOM  VIEW –

Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the

reading on the speed checker or frequency counter becomes in
specification.

Specification: Constant speed

[MENU]

 button

: ON (light up SET UP and

PLAY MODE)

Preset 

[DISC +]

t 

[+             ]

 (

t) buttons

: NR off

[DSO]

 (BAS, TRE) button

: off

[SOUND]

 (BAL) button

: Center

[SOUND]

 (FAD (Front)) button : Center

[SOUND]

 (FAD (Rear)) button

: Center

VOLUME CONTROL dial

: Maximum

Procedure:
1. Put the set into the FWD PB mode.
2. Adjust RV230 (L-CH) and RV240 (R-CH) so that the level

meter reading is –6±0.5 dB (0.37 to 0.41 V).

      

0 dB=0.775 V

Speed checker

Frequency counter

–1.5 to +2.5%

2,955 to 3,075 Hz

Ω

> M







Tuner section adjustments are done automatically in this set.