Sony XR-1800 / XR-1803 / XR-1804 Service Manual ▷ View online
– 13 –
Adjustment Location:
Tape Speed Adjustment
RV1 MW Auto Scan/Stop Level Adjustment
TU100
RV2 FM Auto Scan/Stop Level Adjustment
RV3 FM Noise Focus Adjustment
RV4 FM Stereo Separation Adjustment
CN901
S1
FREQUENCY
SELECT
SWITCH
SWITCH
10 k (MW)
200 k (FM)
9 k (MW)
50 k (FM)
↔
TP2 (SD)
– SET BOTTOM VIEW –
– SET UPPER VIEW –
– 14 –
SECTION 5
DIAGRAMS
•
Pin No.
Pin Name
I/O
Function
1
XIN
I
System clock input terminal (4.5 MHz)
2
TEST2
I
Connected to ground
3
NC
I
Not used (fixed at “H”)
4
AM-SD
I
AM signal meter voltage detection input from the FM/AM tuner unit (TU100) “H” active
5
FM-SD
I
FM signal meter voltage detection input from the FM/AM tuner unit (TU100) “H” active
6
STEREO
I
Stereo detection signal input from the FM/AM tuner unit (TU100) (Commonly used for stereo
display input) FM stereo detection at input of “L”
display input) FM stereo detection at input of “L”
7
MOTOR
O
Capstan/reel motor (M901) drive signal output “H”: motor on
8
AMP-MUTE2
O
Muting control signal output to the power amplifier (IC500) “L”: muting on
9
MW/SW
O
MW/SW selection signal output to the FM/AM tuner unit (TU100) “H”: MW, “L”: SW
Used for the XR-1804 only
Used for the XR-1804 only
10
—
O
Not used (open)
11
BEEP
O
Beep sound signal output terminal “H” active
12
POWER-ON
O
Power on/off control signal output “H”: power on
13
ILL-ON
O
Power on/off control signal output for the liquid crystal display driver (IC900), illumination lamp
and back light lamp “H”: power on
and back light lamp “H”: power on
14
N/R
I
Tape direction switch (S901) input terminal “H”: forward side, “L”: reverse side
15
TAPE-IN
I
Tape in detection switch (S903) input terminal “L”: tape in
16
FF-REW
I
FF/REW detection switch (S902) input terminal “L”: FF/REW mode
17
K1
I
Key matrix return signal input terminal Not used (fixed at “L”)
18
K0
I
Key matrix return signal input terminal
19
AMP-ON
O
Standby on/off signal output to the power amplifier (IC500) “L”: standby, “H”: amp on
20
SEEK
O
Seek control signal output to the FM/AM tuner unit (TU100) “H” active
Used for the XR-1800: E model only
Used for the XR-1800: E model only
21
SEEK
O
Seek control signal output to the FM/AM tuner unit (TU100) “L” active
Used for the except XR-1800: E model
Used for the except XR-1800: E model
22
LOCAL/DX
O
Local/DX selection signal output to the FM/AM tuner unit (TU100) “L”: DX, “H”: local
23, 24
—
O
Not used (open)
25
T2
O
Key matrix scan signal output terminal Used for the XR-1800: E model and XR-1804
26
T1
O
Key matrix scan signal output terminal Not used (open)
27
T0
O
Key matrix scan signal output terminal Used for the XR-1800: AEP, UK models
28
VOL-CE
O
Chip enable signal output to the electrical volume (IC450) “H” active
29
VOL-DI
O
Serial data output to the electrical volume (IC450) “H” active
30
VOL-CL
O
Serial data transfer clock signal output to the electrical volume (IC450)
31
VDD
—
Power supply terminal (+5V)
32
MUTE-REQ
I
Muting request signal input terminal (“H” active) “L”: accessory on, “H”: accessory off
33
BAND-KEY
I
TUNER switch (S900) input terminal “L” is input when pressing the switch
34
PANEL-IN
I
Detects the removal of the attaching and removing type front panel block “L”: attaching
35
NC
I
Not used (fixed at “L”)
36 to 40
—
O
Not used (open)
41
MUTE
O
Audio muting on/off control signal output terminal “H”: muting on Not used (open)
42
—
O
Not used (open)
43
AMP-MUTE
O
Amp muting on/off control signal output terminal “L”: muting on Not used (open)
44
ANT-REM
O
Control signal output for the external power antenna and external amplifier “H” active
45 to 48
—
O
Not used (open)
MAIN BOARD IC1 (SYSTEM CONTROLLER)
LC72322N-9400 (XR-1800), LC72322N-9399 (XR-1803), LC72322N-9412 (XR-1804)
LC72322N-9400 (XR-1800), LC72322N-9399 (XR-1803), LC72322N-9412 (XR-1804)
5-1.
IC PIN FUNCTION DESCRIPTION
– 15 –
Pin No.
Pin Name
I/O
Function
49
KS2
O
50
KS1
O
Key matrix scan signal output terminal
51
KS0
O
52
—
O
Not used (open)
53
LCD-CLK
O
Serial data transfer clock signal output to the liquid crystal display driver (IC900)
54
LCD-CE
O
Chip enable signal output to the liquid crystal display driver (IC900) “H” active
55
LCD-DATA
O
Serial data output to the liquid crystal display driver (IC900) “H” active
56
AM-ON
O
AM system power supply on/off control signal output terminal “H”: AM on
57
MONO
O
Not used (open)
58 to 60
—
O
Not used (open)
61
FM-ON
O
FM system power supply on/off control signal output terminal “H”: FM on
62
TUNER-ON
O
Tuner system power supply on/off control signal output terminal “H”: tuner on
Not used (open)
Not used (open)
63
MW/LW
O
MW/LW selection signal output terminal “L”: MW, “H”: LW Not used (open)
64, 65
—
O
Not used (open)
66
NC
I
Not used (fixed at “L”)
67
CE
I
Accessory switch on/off detection signal input terminal
“H”: accessory on, “L”: accessory off (hold mode)
“H”: accessory on, “L”: accessory off (hold mode)
68
RESET
I
System reset signal input terminal “L”: reset
69
KEY-IN
I
Key matrix return signal input terminal (A/D input)
70
IFIN
I
FM and AM intermediate frequency detection signal input from the FM/AM tuner unit (TU100)
71
NC
I
Not used (fixed at “L”)
72
BU-CHECK
I
Battery detect signal input terminal
73
VDD
—
Power supply terminal (+5V)
74
FMIN
I
FM local oscillator input from the FM/AM tuner unit (TU100)
75
AMIN
I
AM local oscillator input from the FM/AM tuner unit (TU100)
76
VSS
—
Ground terminal
77
EO
O
Main charge-pump control signal output terminal
78
—
O
Not used (open)
79
TEST1
I
Connected to ground
80
XOUT
O
System clock output terminal (4.5 MHz)
– 16 –
5-2.
NOTE FOR PRINTED WIRING BOARDS
AND SCHEMATIC DIAGRAMS
AND SCHEMATIC DIAGRAMS
• Waveform
1
IC1
1
(XIN)
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
¢
: internal component.
•
2
: nonflammable resistor.
•
C
: panel designation.
•
U
: B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from ACC and BATT cords.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
no mark : FM
(
) : MW
〈〈
〉〉
: SW (XR-1804 only)
[
] : TAPE PLAYBACK
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
• Signal path.
F
: FM
f
: MW (LW/SW)
E
: TAPE PLAYBACK
Note on Printed Wiring Boards:
• X
: parts extracted from the component side.
• Y
: parts extracted from the conductor side.
•
¢
: internal component.
• b
: Pattern from the side which enables seeing.
2 Vp-p
222 ns
Click on the first or last page to see other XR-1800 / XR-1803 / XR-1804 service manuals if exist.