Sony XM-ZZR3301 Service Manual ▷ View online
XM-ZZR3301
9
SECTION 2
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
Note: Follow the disassembly procedure in the numerical order given.
2-1. BOTTOM PLATE
2-1. BOTTOM
PLATE
(Page
9)
2-2. MAIN BOARD SECTION
(Page
(Page
10)
SET
2-3. ILLUMI
BOARD
(Page
10)
2-4. MAIN
BOARD
(Page
11)
bottom plate
six screws
(+B, TT, B-TYPE, 3XL)
(+B, TT, B-TYPE, 3XL)
screw
(+BVST 3
(+BVST 3
×6)
XM-ZZR3301
10
2-2. MAIN BOARD SECTION
2-3. ILLUMI BOARD
CN102 (2P)
screw
(+B, TT, B-TYPE, 3XL)
(+B, TT, B-TYPE, 3XL)
screw
(+B, TT, B-TYPE, 3XL)
(+B, TT, B-TYPE, 3XL)
three screws
(+P, TT, B-TYPE, 3XL)
(+P, TT, B-TYPE, 3XL)
three screws
(+P, TT, B-TYPE, 3XL)
(+P, TT, B-TYPE, 3XL)
MAIN board section
After unfastening the screw,
taping with the screw inserted
facilitates the work.
taping with the screw inserted
facilitates the work.
ILLUMI board
three screws
(+B, TT, B-TYPE, 3XL)
(+B, TT, B-TYPE, 3XL)
XM-ZZR3301
11
2-4. MAIN BOARD
front panel
MAIN board
two screws
(+P, TT, B-TYPE, 3XL)
(+P, TT, B-TYPE, 3XL)
two screws
(+P, TT, B-TYPE, 3XL)
(+P, TT, B-TYPE, 3XL)
XM-ZZR3301
12
SECTION 3
DIAGRAMS
For Schematic Diagrams.
Note:
• All capacitors are in μF unless otherwise noted. (p: pF) 50
• All capacitors are in μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.
•
2 : nonfl ammable resistor.
•
C : panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
(In addition to this, the necessary note is printed in each block.)
•
A : B+ Line.
•
B : B– Line.
• Power Voltage is dc 14.4 V and fed with regulated dc
power supply from + 12 V and REM terminals.
• Voltage and waveform are dc with respect to ground un-
der no-signal condition.
• Voltages are taken with VOM (Input impedance 10 M
Ω).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F :
AUDIO
For Printed Wiring Boards.
Note:
•
•
X : Parts extracted from the component side.
• a :
Through
hole.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note:
The components identi-
fi
The components identi-
fi
ed by mark
0 or dotted
line with mark
0 are criti-
cal for safety.
Replace only with part
number specifi ed.
Replace only with part
number specifi ed.
Note:
Les composants identifi és
par une marque
Les composants identifi és
par une marque
0 sont
critiques pour la sécurité.
Ne les remplacer que par
une piéce portant le nu-
méro spécifi é.
Ne les remplacer que par
une piéce portant le nu-
méro spécifi é.
• Waveform
IC901
1 V/DIV, 5 μsec/DIV
2.2 Vp-p
17.5 μsec
Click on the first or last page to see other XM-ZZR3301 service manuals if exist.