DOWNLOAD Sony XAV-722 / XAV-72BT / XAV-E722 Service Manual ↓ Size: 7.64 MB | Pages: 111 in PDF or view online for FREE

56

M_RSSET

O

Reset signal output to the DVD processor and fl ash memory    “L”: reset

57

M_CTS

O

Clear to send signal output to the DVD processor

58, 59

DST_SEL0, 

DST_SEL1

I

Destination setting terminal

60

VCC

-

Power supply terminal (+3.3V)

61

DST_SEL2

I

Destination setting terminal

62

VSS

-

Ground terminal

63

NCO

O

Not used

64

ILL_IN

I

Illumination line detection signal input terminal for the automatic dimmer control    
“L”: dimmer on

65

RC_IN1

I

Rotary commander shift key input terminal

66

TEL_ATT

I

Telephone muting detection signal input terminal
At input of “H”, the audio signal is attenuated by 20 dB

67

EJECT

O

Loading motor drive signal (eject direction) output terminal    “H”: motor on

68

LOAD

O

Loading motor drive signal (loading direction) output terminal    “H”: motor on

69

DR_ON

O

Power supply on/off control signal output terminal for loading motor driver    “H”: power on

70

NCO

O

Not used

71

BT_RSEST

O

Reset signal output to the Bluetooth controller    “L”: reset (XAV-72BT)

72

USB_ON

O

Power supply on/off control signal output terminal for USB section    “H”: power on

73

BU_IN

I

Back up power supply detection signal input from the SONY bus interface    
“H”: buck up power on (XAV-72BT: US and Canadian models)
Back up power supply detection signal input terminal    
“H”: back up power on (except XAV-72BT: US and Canadian models)

74

USB_OVER

I

USB over current detection signal input from the switching regulator    “L”: over current

75

BT_TX

O

Serial data output to the Bluetooth controller (XAV-72BT)

76

BT_RX

I

Serial data input from the Bluetooth controller (XAV-72BT)

77

RE_0

I

Jog dial pulse input terminal    Not used

78

RE_1

I

Jog dial pulse input terminal    Not used

79

NCO

O

Not used

80

BT_POWER

O

Power supply on/off control signal output terminal for Bluetooth section (XAV-72BT)

81

BT_ACTIVE

I

Start state checking signal input from the Bluetooth controller (XAV-72BT)

82

BT_SYSON

O

Start signal output to the Bluetooth controller (XAV-72BT)

83

VSM

I

FM and AM signal-meter voltage detection signal input from the FM/AM PLL (A/D input)

84

KEY_IN0

I

Front panel key input terminal (A/D input)

85

KEY_IN1

I

Key input terminal (A/D input)    Not used

86

RC_IN0

I

Rotary commander key input terminal (A/D input)

87

RCACK

I

Acknowledge signal (wake up signal) input terminal for the rotary commander key entry    
Acknowledge signal is input to accept any function key in the standby state    On at input of “H”

88

KEYACK

I

Acknowledge signal (wake up signal) input terminal for the front panel key entry    
Acknowledge signal is input to accept any function key in the standby state    On at input of “H”

89, 90

NCO

O

Not used

91

MODEL_SEL4

I

Model (4V preout) setting terminal    “H”: 4V preout is set    Fixed at “H” in this unit

92

BUS_ON

O

SONY BUS on/off control signal output to the SONY bus interface    “L”: bus on 
(XAV-72BT: US and Canadian models only)

93

SYSRST

O

Reset signal output to the SONY bus interface    “L”: reset 
(XAV-72BT: US and Canadian models only)

94

AVSS

-

Ground terminal

95

MODEL_SEL3

I

Model (other companies navigation) setting terminal    “H”: other companies navigation is set    
“L”: XAV-72BT: US, Canadian, AEP, UK and E (NTSC) models/XAV-E722, “H”: XAV-72BT: E 
(PAL), Saudi Arabia, South African and Hong Kong models/XAV-722

96

VREF

I

Reference voltage (+3.3V) input terminal (for A/D converter)

97

AVCC

-

Power supply terminal (+3.3V)

98

UNISI

I

Serial data input from the SONY bus interface (XAV-72BT: US and Canadian models only)

99

UNISO

O

Serial data output to the SONY bus interface (XAV-72BT: US and Canadian models only)

100

UNICKO

O

Serial data transfer clock signal output to the SONY bus interface 
(XAV-72BT: US and Canadian models only)

1

YIN3

I

Analog YUV video signal (Y) input from the DVD processor

2

YIN2

I

Analog RGB video signal (green) input from the EXT connector for external navigation 
(XAV-72BT: E (PAL), Saudi Arabia, South African and Hong Kong models/XAV-722)

3

YIN1

I

Analog composite video signal input from the CAMERA IN jack

4

YIN0

I

Analog composite video signal input from the AUX1 VIDEO IN jack or AUX2 VIDEO IN jack

5

YGND

-

Ground terminal

6

AGND

-

Ground terminal

7

AVDD1_1.8V

-

Power supply terminal (+1.8V)

8

CIN2

I

Analog video signal input terminal    Not used

9

CIN1

I

Analog RGB video signal (blue) input from the EXT connector for external navigation 
(XAV-72BT: E (PAL), Saudi Arabia, South African and Hong Kong models/XAV-722)

10

CIN0

I

Analog YUV video signal (U) input from the DVD processor

11

VIN1

I

Analog RGB video signal (red) input from the EXT connector for external navigation 
(XAV-72BT: E (PAL), Saudi Arabia, South African and Hong Kong models/XAV-722)

12

VIN0

I

Analog YUV video signal (V) input from the DVD processor

13

AVDD33

-

Power supply terminal (+3.3V)

14, 15

SEN0, SEN1

I

Analog sensing signal input terminal    Not used

16

COMOUT

O

Analog VCOM signal output terminal    Not used

17, 18

LADIN0, LADIN1

I

Low-speed A/D converter signal input terminal    Not used

19

AVSS33

-

Ground terminal

20

DAVDDA33

-

Power supply terminal (+3.3V)

21

ROUT

O

Analog RGB video signal (red) output terminal    Not used

22

GOUT

O

Analog RGB video signal (green) output terminal    Not used

23

BOUT

O

Analog RGB video signal (blue) output terminal    Not used

24

DAVSSA33

-

Ground terminal

25

GPIO1

O

Non-input signal detection signal output to the visual controller    
“L”: non-input signal is detected

26

VDD18

-

Power supply terminal (+1.8V)

27

VSS18

-

Ground terminal

28

FPBIAS

O

Power supply on/off control signal output terminal for fl at panel back light bias    
Not used

29

FPPWC

O

Power supply on/off control signal output terminal for fl at panel display    Not used

30

FPPWM

O

Dimmer control signal output terminal for fl at panel back light    Not used

31

TRCLK

O

Row driver shift clock signal output terminal    Not used

32

GPIO2

O

Not used

33

TCINV

O

TCON column driver inversion terminal    Not used

34

TCPOLP

O

Column driver polarity (positive) terminal    Not used

35

TCPOLN

O

Column driver polarity (negative) terminal    Not used

36

TCLP

O

Column driver load pulse signal output terminal    Not used

37

FPCLK

O

Clock signal output to the video processor

38

FPVS

O

Vertical sync signal output to the video processor

39

VDD33

-

Power supply terminal (+3.3V)

40

FPHS

O

Horizontal sync signal output to the video processor

41

FPDE

O

Data valid signal output terminal for fl at panel    Not used

42

VSS33

-

Ground terminal

43, 44

FPR0, FPR1

O

Digital RGB video signal (red) output terminal    Not used

45, 46

FPR2, FPR3

O

Digital RGB video signal (red) output to the video processor

47

VSS18

-

Ground terminal

48

VDD18

-

Power supply terminal (+1.8V)

49 to 52

FPR4 to FPR7

O

Digital  RGB video signal (red) output to the video processor

53

VDD33

-

Power supply terminal (+3.3V)

54, 55

FPG0, FPG1

O

Digital RGB video signal (green) output terminal    Not used

56, 57

FPG2, FPG3

O

Digital RGB video signal (green) output to the video processor

58

VSS33

-

Ground terminal

59 to 62

FPG4 to FPG7

O

Digital RGB video signal (green) output to the video processor

63, 64

FPB0, FPB1

O

Digital RGB video signal (blue) output terminal    Not used

65, 66

FPB2, FPB3

O

Digital RGB video signal (blue) output to the video processor

67

VDD33

-

Power supply terminal (+3.3V)

68 to 71

FPB4 to FPB7

O

Digital RGB video signal (blue) output to the video processor

72

VSS33

-

Ground terminal

73

MCU_EN

I

MCU enable signal input terminal    Not used

74

XTAL27O

O

System clock output terminal (27 MHz)

75

XTAL27I

I

System clock input terminal (27 MHz)

76

RST

I

Reset signal input from the visual controller    “L”: reset

77

TEST

I

Test terminal

78

PWRDN

I

Power down signal input terminal    Not used

79

SDAT

I/O

Two-way I2C data bus with the visual controller

80

SCLK

I

I2C clock signal input from the visual controller

81

VDD18

-

Power supply terminal (+1.8V)

82

VSS18

-

Ground terminal

83, 84

DTV0 (NC), 

DTV1 (NC)

I

Digital television signal input terminal    Not used

85 to 90

DTV2 (B0) to 

DTV7 (B5)

I

Digital television signal input terminal    Not used

91, 92

DTV8 (NC), 

DTV9 (NC)

I

Digital television signal input terminal    Not used

93 to 98

DTV10 (G0) to 

DTV15 (G5)

I

Digital television signal input terminal    Not used

99, 100

DTV16 (NC), 

DTV17 (NC)

I

Digital television signal input terminal    Not used

101

DTV18 (R0)

I

Digital television signal input terminal    Not used

102

VDD33

-

Power supply terminal (+3.3V)

103

VSS33

-

Ground terminal

104 to 

108

DTV19 (R1) to 

DTV23 (R5)

I

Digital television signal input terminal    Not used

109

VDD18

-

Power supply terminal (+1.8V)

110

VSS18

-

Ground terminal

111

DTVCLK

I

Clock signal input terminal for DTV interface    Not used

112

DTVDE

I/O

Data valid signal input/output terminal for DTV interface    Not used

113

DTVHS

I/O

Horizontal sync signal input/output terminal for DTV interface    Not used

114

DTVVS

I/O

Vertical sync signal input/output terminal for DTV interface    Not used

115

VSYNC

I

Vertical sync signal input terminal    Not used

116

CSYNC

I

CSYNC signal input from the EXT connector for external navigation 
(XAV-72BT: E (PAL), Saudi Arabia, South African and Hong Kong models/XAV-722)

117

SSVDD18

-

Power supply terminal (+1.8V)

118

SSVSS18

-

Ground terminal

119

VDDD18

-

Power supply terminal (+1.8V)

120

VSSD18

-

Ground terminal

121

LVDDA18

-

Power supply terminal (+1.8V)

122

LVSSA18

-

Ground terminal

123

AGND3

-

Ground terminal

124, 125

AVDD3_1.8V, 

AVDD2_1.8V

-

Power supply terminal (+1.8V)

126

AGND2

-

Ground terminal

127

YOUT

O

Analog video signal (Y) output terminal    Not used

128

SOYIN

I

Sync signal on analog YUV video signal (Y) input terminal

1

VCOM_AMP

O

VCOM amplitude voltage control signal output terminal

2

VCOM_BIAS

O

VCOM bias voltage control signal output terminal

3

NCO

O

Not used

4

SPEED_IN

I

Speed pulse input terminal    Not used

5

NCO

O

Not used

6

BYTE

I

External data bus width selection signal input terminal    Fixed at “L” (16 bit) in this unit

7

FLASH_W

I

Flash writing terminal    “L”: normally operation mode, “H”: writing mode

8

XCIN

I

Low-speed system clock input terminal    Not used

9

XCOUT

O

Low-speed system clock output terminal    Not used

10

RESET

I

Reset signal input from the master controller and reset signal generator    “L”: reset

11

XOUT

O

High-speed system clock output terminal (6 MHz)

12

VSS

-

Ground terminal

13

XIN

I

High-speed system clock input terminal (6 MHz)

14

VCC1

-

Power supply terminal (+3.3V)

15

NMI

I

Non-maskable interrupt signal input terminal    Fixed at “H” in this unit

16

MASTER_IF

I

Communication start signal input from the master controller

17

CPV

I

Vertical sync signal input from the video processor

18

PHOTO

I

Monitor open/close photo detection signal input terminal

19

NCO

O

Not used

20

VISUAL_RX

I

Serial data input from the master controller

21

NCO

O

Not used

22

VISUAL_TX

O

Serial data output to the master controller

23

BT_IND

O

LED drive signal output terminal for Bluetooth indicator    “H”: LED on

24

KEY_PWM

O

LED drive signal output terminal for front panel key illumination 

25

BL_ENA

O

LED drive signal output to the backlight controller for liquid crystal display back light    
“H”: LED on

26

BL_PWM

O

Dimmer control signal output to the backlight controller for liquid crystal display back light    

27

I2CKO

O

I2C clock signal output to the video decoder

28

I2SIO

I/O

Two-way I2C data bus with the video decoder

29

FLASH_TX

O

Serial data output to the fl ash writing connector

30

FLASH_RX

I

Serial data input from the fl ash writing connector

31

F_CLK

O

Serial data transfer clock signal output terminal at the fl ash writing mode

32

BUSY

O

Busy signal output terminal at the fl ash writing mode

33

NAVI_TX

O

Serial data output to the EXT connector for external navigation 
(XAV-72BT: E (PAL), Saudi Arabia, South African and Hong Kong models/XAV-722)

34

NAVI_RX

I

Serial data input from the EXT connector for external navigation 
(XAV-72BT: E (PAL), Saudi Arabia, South African and Hong Kong models/XAV-722)

35

NAVI_DET

I

External navigation detection signal input terminal    “L”: navigation is detected 
(XAV-72BT: E (PAL), Saudi Arabia, South African and Hong Kong models/XAV-722)

36

NAVI_RTS

O

Request to send signal output terminal for navigation    Not used

37

BL_STATUSP

I

Power converter status input from the backlight controller

38

BL_STATUSL

I

LED operation status input from the backlight controller

39

HOLD

I

External data bus terminal at the fl ash writing mode    Fixed at “L” in this unit

40

DEC_GPIO_1

I

Non-input signal detection signal input from the video decoder    
“L”: non-input signal is detected

41

DEC_GPIO_2

O

Not used

42

DEC_RST

O

Reset signal output to the video decoder    “L”: reset

43

NCO

O

Not used

44

WRI/WR

I

External data bus terminal at the fl ash writing mode    Fixed at “H” in this unit

45 to 47

NCO

O

Not used

48

NAVI_CTS

I

Clear to send signal input terminal for navigation    Not used

49

MOTOR_ON

O

Power supply on/off control signal output terminal for monitor open/close motor driver    
“H”: power on

50

NCO

O

Not used

51

M_LOW

O

Monitor open/close speed (low) control signal output terminal

52

M_MID

O

Monitor open/close speed (middle) control signal output terminal

53

OPEN

I

Monitor open detection switch input terminal

54

CLOSE

I

Monitor close detection switch input terminal

55

MOTOR+

O

Monitor open/close motor drive signal (forward direction) output to the monitor open/close 
motor driver