Sony XAV-701HD Service Manual ▷ View online
XAV-701HD
61
MAIN BOARD IC201
PD720114GA-YEU-A-SAK (USB INTERFACE)
Pin No.
Pin Name
I/O
Description
1
VDD25OUT
O
Internal regulator power supply voltage (+2.5V) output terminal
2
VSSREG
-
Ground terminal (for internal regulator)
3 to 6
LED4 to LED1
-
Not used
7
GREEN
-
Not used
8
AMBER
-
Not used
9
VDD33
-
Power supply terminal (+3.3V)
10
X1
I
System clock input terminal (30 MHz)
11
X2
O
System clock output terminal (30 MHz)
12
VDD25
-
Power supply terminal (+2.5V)
13
BUS_B
I
Power supply setting terminal Fixed at “H” in this unit
14
TEST
I
Test mode control signal input terminal
15
RREF
-
Reference resistor connection terminal
16
AVSS (R)
-
Ground terminal
17
AVDD
-
Power supply terminal (+2.5V)
18
AVSS
-
Ground terminal
19
AVDD
-
Power supply terminal (+2.5V)
20
VDD33
-
Power supply terminal (+3.3V)
21
DMU
I/O
Two-way USB data (negative) bus with the panel section
22
DPU
I/O
Two-way USB data (positive) bus with the panel section
23
VSS
-
Ground terminal
24
VDD25
-
Power supply terminal (+2.5V)
25
DM1
I/O
Two-way USB data (negative) bus with the connection cord
26
DP1
I/O
Two-way USB data (positive) bus with the connection cord
27
VSS
-
Ground terminal
28
DM2
I/O
Two-way USB data (negative) bus terminal Not used
29
DP2
I/O
Two-way USB data (positive) bus terminal Not used
30
VDD33
-
Power supply terminal (+3.3V)
31
DM3
I/O
Two-way USB data (negative) bus terminal Not used
32
DP3
I/O
Two-way USB data (positive) bus terminal Not used
33
VDD25
-
Power supply terminal (+2.5V)
34
DM4
I/O
Two-way USB data (negative) bus with the connection cord
35
DP4
I/O
Two-way USB data (positive) bus with the connection cord
36
VSS
-
Ground terminal
37
SYSRSTB
I
Power supply on/off control signal input form the system controller “H”: power on
38
PPB4
-
Not used
39
CSB4
-
Not used
40
PPB3
-
Not used
41
CSB3
-
Not used
42
VSS
-
Ground terminal
43
PPB2
-
Not used
44
CSB2
-
Not used
45
PPB1
-
Not used
46
CSB1
-
Not used
47
VBUSM
I
VBUS monitor terminal Not used
48
VDD33REG
I
Internal regulator power supply voltage (+3.3V) input terminal
XAV-701HD
62
MAIN BOARD IC502 R5F3650NCDZ97FB (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
SPEED_IN
I
Speed pulse signal input terminal
2
SIRCS
I
SIRCS signal input from the panel section
3 to 5
MODEL_SEL1 to
MODEL_SEL3
I
Model setting terminal
6
BYTE
I
External data bus width selection signal input terminal Fixed at “L” (16 bit) in this unit
7
FLASH_W
I
Flash writing terminal “L”: normally operation mode, “H”: writing mode
8
XCIN
I
Low-speed system clock input terminal (32.768 kHz)
9
XCOUT
O
Low-speed system clock output terminal (32.768 kHz)
10
RESET
I
System reset signal input from the reset signal generator and panel section “L”: reset
11
XOUT
O
High-speed system clock output terminal (6 MHz)
12
VSS
-
Ground terminal
13
XIN
I
High-speed system clock input terminal (6 MHz)
14
VCC
-
Power supply terminal (+3.3V)
15
NMI
I
Non-maskable interrupt signal input terminal Fixed at “H” in this unit
16
MODEL_SEL4
I
Model setting terminal
17
BU_IN
I
Back up power supply detection signal input terminal “H”: back up power on
18
PHOTO
I
Monitor open/close photo detection signal input terminal
19
REVERSE_IN
I
Reverse shift position detection signal input terminal “L”: reverse shift position
20
NAVI/XM_Rx
I
Serial data input from the SIRIUS/XM IN connector
21
VOL_ATT
O
Audio muting on/off control signal output to the electrical volume “L”: muting on
22
NAVI/XM_Tx
O
Serial data output to the SIRIUS/XM IN connector
23
NAVI_DET
I
External navigation detection signal input terminal Not used
24
FSW_OUT
O
External sync signal output to the DC/DC converter, line amplifi er and panel section
25
STB
O
Standby signal output to the power amplifi er “L”: standby
26
BEEP
O
Beep sound output to the power amplifi er
27
I2C_SCK
O
I2C clock signal output to the electrical volume, EEPROM, FM/AM HD tuner unit and power
amplifi er
amplifi er
28
I2C_SIO
I/O
Two-way I2C data bus with the electrical volume, EEPROM, FM/AM HD tuner unit and power
amplifi er
amplifi er
29
FLASH_Tx
O
Serial data output to the fl ash writing connector
30
FLASH_Rx
I
Serial data input from the fl ash writing connector
31
F_CLK
O
Serial data transfer clock signal output terminal Not used
32
BUSY
O
Busy signal output terminal Not used
33
HIT2_SDA
I/O
Two-way I2C data bus with the FM/AM HD tuner unit
34
HIT2_SCL
O
I2C clock signal output to the FM/AM HD tuner unit
35
DIAG
I
Diagnostic signal input from the power amplifi er
36
XM_EN
O
Power supply on/off control signal output to the SIRIUS/XM IN connector
37
ZxZ_ATT
O
ZxZ audio muting on/off control signal output terminal
38
NCO
-
Not used
39
HOLD
I
External data bus terminal at the fl ash writing mode Fixed at “L” in this unit
40
HIT2_RST
O
Reset signal output to the FM/AM HD tuner unit “L”: reset
41
NCO
-
Not used
42
PARKING_IN
I
Side brake (parking brake) position detection signal input terminal “L”: brake on
43
ACCIN
I
Accessory power supply detection signal input terminal “L”: accessory power on
44
WRI/WR
I
External data bus terminal at the fl ash writing mode Fixed at “H” in this unit
45
MECHA_Tx
O
Serial data output to the DVD processor
46
MECHA_Rx
I
Serial data input from the DVD processor
47
ATT_CNT
O
Audio muting on/off control signal output terminal Not used
48
MECHA_RTS
I
Request to send signal input from the DVD processor
49
ATT
O
System muting on/off control signal output terminal “H”: muting on
50
SERVICE
I
Setting teminal for service “L”: for service, “H”: normal operation
51
EXTATT_XEN
O
External input audio muting on/off control signal output terminal
“L”: disc play, “H”: other source play or source off
“L”: disc play, “H”: other source play or source off
52
Z_MUTE
I
Zero data muting on/off control signal input from the D/A converter “H”: muting on
53
SELF_SW
I
Self loading position detection switch input terminal
54
IN_SW
I
Disc insert detection switch input terminal
55
D_SW
I
Chucking end detection switch input terminal
56
MECHA_RESET
O
Reset signal output to the DVD processor and fl ash memory “L”: reset
57
MECHA_CTS
O
Clear to send signal output to the DVD processor
XAV-701HD
63
Pin No.
Pin Name
I/O
Description
58
IPOD_DET
I
iPod/iPhone detection signal input terminal “L”: iPod/iPhone is detected
59
AP_CNT1
-
Not used
60
VCC
-
Power supply terminal (+3.3V)
61
AP_RESET
O
Reset signal output to the panel section “L”: reset
62
VSS
-
Ground terminal
63
AP_ON
O
Power supply on/off control signal output to the DC/DC converter “H”: power on
64
ILL_IN
I
Illumination line detection signal input terminal for the automatic dimmer control
“L”: dimmer on
“L”: dimmer on
65
NCO
-
Not used
66
EJECT
O
Loading motor drive signal (eject direction) output terminal “H”: motor on
67
LOAD
O
Loading motor drive signal (loading direction) output terminal “H”: motor on
68
DR_ON
O
Power supply on/off control signal output terminal for loading motor driver “H”: power on
69
VMUTE
O
Video muting on/off control signal output to the video select IC “L”: muting on
70, 71
SEL_VOUT0,
SEL_VOUT1
O
Video signal selection signal output to the video select IC
72
NOSE_SW
I
Error signal input from the front panel section “L”: normal mode
73, 74
SEL_VIN0, SEL_VIN1
O
Video signal selection signal output to the video select IC
75
AP_Tx
O
Serial data output to the panel section
76
AP_Rx
I
Serial data input from the panel section
77
EN_SYS
O
Power supply on/off control signal output terminal for DC/DC converter “H”: power on
78
IPOD
O
iPod connection mode setting terminal Fixed at “L” in this unit
79
USB_ON
O
Power supply on/off control signal output terminal for USB section “H”: power on
80
USB_OVER
I
USB over current detection signal input from the DC/DC converter “L”: over current
81
RE_0
I
Jog dial pulse input from the panel section (A phase input) (for volume)
82
RE_1
I
Jog dial pulse input from the panel section (B phase input) (for volume)
83
IDET
I
Monitor open/close motor drive current detection signal input from the monitor open/close
motor driver
motor driver
84
TEMP
I
Temperature detection signal input terminal
85
KEY_IN0
I
Front panel key input terminal (A/D input)
86
RC_IN0
I
Rotary commander key input terminal (A/D input)
87
RCACK
I
Acknowledge signal (wake up signal) input terminal for the rotary commander key entry
Acknowledge signal is input to accept any function key in the standby state On at input of “H”
Acknowledge signal is input to accept any function key in the standby state On at input of “H”
88
KEYACK
I
Acknowledge signal (wake up signal) input terminal for the front panel key entry
Acknowledge signal is input to accept any function key in the standby state On at input of “H”
Acknowledge signal is input to accept any function key in the standby state On at input of “H”
89
RC_IN1
I
Rotary commander key input terminal
90
M_LOW
O
Monitor open/close speed (low) control signal output terminal
91
M_MID
O
Monitor open/close speed (middle) control signal output terminal
92
OPEN
I
Monitor open detection switch input terminal
93
CLOSE
I
Monitor close detection switch input terminal
94
AVSS
-
Ground terminal
95
MOTOR_ON
O
Power supply on/off control signal output terminal for monitor open/close motor driver
“H”: power on
“H”: power on
96
VREF
I
Reference voltage (+3.3V) input terminal (for A/D converter)
97
AVCC
-
Power supply terminal (+3.3V)
98
MOTOR_+
O
Monitor open/close motor drive signal (forward direction) output to the monitor open/close
motor driver
motor driver
99
MOTOR_-
O
Monitor open/close motor drive signal (reverse direction) output to the monitor open/close
motor driver
motor driver
100
MODEL_SEL0
I
Model setting terminal
64
XAV-701HD
SECTION 6
EXPLODED VIEWS
1
2-892-754-01 SPRING (RATTLE), TENSION (See Note 2)
2
3-216-336-01 HOOK SPRING (See Note 2)
3
4-438-867-01 CUSHION
(SUB7)
4
2-894-799-01 SCREW +PTW S2X5
5
2-892-794-02 SCREW +Z M2X3
6
X-2584-170-1 PANEL
(SUB)
ASSY
CNC1
1-839-912-21 CORD, CONNECTION (20P)
(REVERSE IN/SPEED IN/SUB OUT/
FRONT AUDIO OUT/REAR AUDIO OUT/
AUX1 AUDIO IN/AUX2 AUDIO IN)
PW1
1-839-376-31 CONNECTION CORD FOR AUTOMOBILE
(POWER)
#1
7-685-792-01 SCREW +PTT 2.6X6 (S)
#7
7-685-791-01 SCREW +PTT 2.6X5 (S)
#8
7-627-552-87 SCREW, PRECISION +P 1.7X2.2
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
Parts Color Cabinet’s Color
6-1. OVERALL SECTION
The components identifi ed by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specifi ed.
or dotted line with mark 0 are critical for
safety.
Replace only with part number specifi ed.
Les composants identifi és par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce por-
tant le numéro spécifi é.
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce por-
tant le numéro spécifi é.
not supplied
(LID (DISPLAY) board)
(LID (DISPLAY) board)
not supplied
not supplied
not supplied
3
2
1
5
5
3
4
chassis main section
front panel section
DVD mechanism deck section
(MG-613XF-187)
(MG-613XF-187)
PW1
B
A
A
B
#1
#1
#1
#8
#1
#1
#1
CNC1
6
#1 (for MG-614D-189)
#7 (for MG-613XF-187)
#7 (for MG-613XF-187)
#1 (for MG-614D-189)
#7 (for MG-613XF-187)
#7 (for MG-613XF-187)
(See Note 2)
X
X
(MG-613XF-187 only)
Ver. 1.2
Note 1: Refer to SUPPLEMENT-1 for discrim-
ination of the DVD mechanism deck
(MG-613XF-187 or MG-614D-189).
(MG-613XF-187 or MG-614D-189).
Note 2: These parts are deleted from
the midway of production.
Click on the first or last page to see other XAV-701HD service manuals if exist.