Sony XAV-63 / XAV-63M / XAV-64BT / XAV-64BTM Service Manual ▷ View online
XAV-63/63M/64BT/64BTM
65
DISP BOARD IC2201 MN103SH23UB (VIDEO PROCESSOR)
Pin No.
Pin Name
I/O
Description
1
OSCXO
O
System clock output terminal (33 MHz)
2
OSCXI
I
System clock input terminal (33 MHz)
3 to 7
SDRA3, SDRA4,
SDRA2, SDRA5,
SDRA2, SDRA5,
SDRA1
O
Address signal output to the SD-RAM
8
VSS
-
Ground terminal
9
SDRA6
O
Address signal output to the SD-RAM
10
VDD
-
Power supply terminal (+3.3V)
11, 12
SDRA0, SDRA7
O
Address signal output to the SD-RAM
13
VDDI
-
Power supply terminal (+1.2V)
14, 15
SDRA10, SDRA8
O
Address signal output to the SD-RAM
16
SDRBA1
O
Bank address signal output to the SD-RAM
17
SDRA9
O
Address signal output to the SD-RAM
18
VSS
-
Ground terminal
19
VDD
-
Power supply terminal (+3.3V)
20
SDRBA0
O
Bank address signal output to the SD-RAM
21
SDRA11
O
Address signal output to the SD-RAM
22
NSDRCS
O
Chip select signal output to the SD-RAM
23
SDRA12
O
Address signal output to the SD-RAM
24
NSDRRAS
O
Row address select signal output to the SD-RAM
25
SDRCKE
O
Clock enable signal output to the SD-RAM
26
NSDRCAS
O
Column address select signal output to the SD-RAM
27
SDCKI
I
Clock signal input from the SDRCKO (pin 30)
28
VDD
-
Power supply terminal (+3.3V)
29
VSS
-
Ground terminal
30
SDRCKO
O
Clock signal output to the SDCKI (pin 27) and SD-RAM
31
NSDRWE
O
Write enable signal output to the SD-RAM
32
SDRDQM1
O
Data mask signal output to the SD-RAM (upper byte)
33
SDRDQM0
O
Data mask signal output to the SD-RAM (lower byte)
34 to 37
SDRD8, SDRD7,
SDRD9, SDRD6
I/O
Two-way data bus with the SD-RAM
38
VDD
-
Power supply terminal (+3.3V)
39
VSS
-
Ground terminal
40 to 48
SDRD10,
SDRD5, SDRD11,
SDRD4,SDRD12,
SDRD3, SDRD13,
SDRD2, SDRD14
I/O
Two-way data bus with the SD-RAM
49
VDD
-
Power supply terminal (+3.3V)
50
VSS
-
Ground terminal
51
VDDI
-
Power supply terminal (+1.2V)
52 to 54
SDRD1, SDRD15,
SDRD0
I/O
Two-way data bus with the SD-RAM
55
NRST
I
Reset signal input from the master controller “L”: reset
56
NMI
I
Non-maskable interrupt signal input terminal Fixed at “H” in this unit
57
LCDICLK
I
Clock signal input terminal Not used
58
TSTC0
I
Test signal input terminal Fixed at “L” in this unit
59
TSTCK
I
Test signal input terminal Fixed at “L” in this unit
60
VSS
-
Ground terminal
61, 62
TSTC1, TSTC2
I
Test signal input terminal Fixed at “L” in this unit
63
PINMD1
I
Mode signal input terminal Fixed at “L” in this unit
64
SDATA
I/O
Two-way data bus terminal for debug
65
VSS
-
Ground terminal
66
VDD
-
Power supply terminal (+3.3V)
67
SCLOCK
I
Clock signal input terminal for debug
68
PINMD0
I
Mode signal input terminal Fixed at “L” in this unit
69
VDDI
-
Power supply terminal (+1.2V)
70, 71
NFRCS0, NFRCS1
O
Chip enable signal output to the fl ash memory
72
NFRWE
O
Write enable signal output to the fl ash memory
73
VSS
-
Ground terminal
XAV-63/63M/64BT/64BTM
66
Pin No.
Pin Name
I/O
Description
74
VDD
-
Power supply terminal (+3.3V)
75
NFROE
O
Output enable signal output to the fl ash memory
76 to 83
FAD0 to FAD7
O
Address signal output to the fl ash memory
84
VSS
-
Ground terminal
85
VDD
-
Power supply terminal (+3.3V)
86 to 93
FAD8 to FAD15
O
Address signal output to the fl ash memory
94
PVPPDRAM
-
Internal D-RAM monitor terminal
95
VDD
-
Power supply terminal (+3.3V)
96
VSS
-
Ground terminal
97
AVDDR
-
Power supply terminal (+3.3V)
98 to 102
FAD16 to FAD20
O
Address signal output to the fl ash memory
103
VDDI
-
Power supply terminal (+1.2V)
104, 105
FAD21, FAD22
O
Address signal output to the fl ash memory
106
VDDI
-
Power supply terminal (+1.2V)
107
VDD
-
Power supply terminal (+3.3V)
108
VSS
-
Ground terminal
109 to
119
FDATA0 to FDATA10
I/O
Two-way data bus with the fl ash memory
120
VDD
-
Power supply terminal (+3.3V)
121
VSS
-
Ground terminal
122 to
126
FDATA11 to FDATA15
I/O
Two-way data bus with the fl ash memory
127
GPIO0 (NC)
O
Not used
128
GPIO1 (NOR_W)
I
Flash writing terminal “L”: normally operation mode, “H”: writing mode
129
GPIO2 (NC)
I/O
Not used
130
GPIO3 (GERDA_IF)
I
Communication start signal input from the master controller
131
GPIO4 (RX)
I
Serial data input from the master controller
132
GPIO5 (TX)
O
Serial data output to the master controller
133
GPIO6 (DEBUG-RX)
I
Debug serial data input terminal Not used
134
VSS
-
Ground terminal
135
VDD
-
Power supply terminal (+3.3V)
136
GPIO7 (DEBUG-TX)
O
Debug serial data output terminal Not used
137
GPIO8 (NC)
O
Not used
138
GPIO9 (STH)
O
Horizontal sync signal output to the liquid crystal display
139 to
144
DVOB0 to DVOB5
I
Digital RGB video signal (blue) input from the video decoder
145
VDDI
-
Power supply terminal (+1.2V)
146 to
151
DVOG0 to DVOG5
I
Digital RGB video signal (green) input from the video decoder
152 to
154
DVOR0 to DVOR2
I
Digital RGB video signal (red) input from the video decoder
155
VSS
-
Ground terminal
156
DVOR3
I
Digital RGB video signal (red) input from the video decoder
157
VDD
-
Power supply terminal (+3.3V)
158, 159
DVOR4, DVOR5
I
Digital RGB video signal (red) input from the video decoder
160
DVOCLK
I
Clock signal input from the video decoder
161
DVOVSY
I
Vertical sync signal input from the video decoder
162
DVOHSY
I
Horizontal sync signal input from the video decoder
163
CMPAOUT
O
External capacitor connection terminal for comparator low-pass fi lter
164
AVOIREF
O
External resistor connection terminal for A/D converter bias
165
AVOVREFH
O
Reference voltage output terminal
166
AVOVREFL
O
Reference voltage output terminal
167
AVOVCMO
O
Reference voltage output terminal
168
AVOINA
I
Analog composite video signal input from the DVD processor
(Russian (Former type), E (PAL), Saudi Arabia and Indian models)
(Russian (Former type), E (PAL), Saudi Arabia and Indian models)
169
AVDDA
-
Power supply terminal (+3.3V)
170
AVOINB
I
Analog composite video signal input from the AUX VIDEO IN jack
(Russian (Former type), E (PAL), Saudi Arabia and Indian models)
(Russian (Former type), E (PAL), Saudi Arabia and Indian models)
171
AVSSA
-
Ground terminal
172
AV1VREFH
O
Reference voltage output terminal
173
AV1VREFL
O
Reference voltage output terminal
Ver. 1.4
Note: Refer to “ABOUT THE DELETION OF EXT TERMINAL” (page 6) for how to distinguish New/Former type of Russian model.
XAV-63/63M/64BT/64BTM
67
Pin No.
Pin Name
I/O
Description
174
AV1VCMO
O
Reference voltage output terminal
175
AV1IN
I
Analog composite video signal input terminal Not used
176
AVDDA2
-
Power supply terminal (+3.3V)
177
AV2VREFH
O
Reference voltage output terminal
178
AV2VREFL
O
Reference voltage output terminal
179
AVSSA2
-
Ground terminal
180
AV2VCMO
O
Reference voltage output terminal
181
AV2IN
I
Analog composite video signal input terminal Not used
182
AVDDP
-
Power supply terminal (+3.3V)
183
TSTIO (NC)
I/O
Internal PLL inspection terminal Not used
184
AVSSP
-
Ground terminal
185 to
188
LCDOB0 to LCDOB3
O
Digital RGB video signal (blue) output to the liquid crystal display
189
VSS
-
Ground terminal
190
VDD
-
Power supply terminal (+3.3V)
191, 192
LCDOB4, LCDOB5
O
Digital RGB video signal (blue) output to the liquid crystal display
193 to
195
LCDOG0 to LCDOG2
O
Digital RGB video signal (green) output to the liquid crystal display
196
VDDI
-
Power supply terminal (+1.2V)
197 to
199
LCDOG3 to LCDOG5
O
Digital RGB video signal (green) output to the liquid crystal display
200
VSS
-
Ground terminal
201
VDD
-
Power supply terminal (+3.3V)
202 to
207
LCDOR0 to LCDOR5
O
Digital RGB video signal (red) output to the liquid crystal display
208
LCDOC0 (STB)
O
LOAD signal output to the liquid crystal display
209
LCDOC1 (STV)
O
Vertical sync signal output to the master controller and liquid crystal display
210
VDD
-
Power supply terminal (+3.3V)
211
VSS
-
Ground terminal
212
LCDOC2 (CPV)
O
Voltage control signal output to the liquid crystal display
213
LCDOC3 (POL)
O
Polarity inversion control output terminal
214
LCDOCLK
O
Clock signal output to the liquid crystal display
215
LCDOC4 (OE)
O
Output enable signal output to the liquid crystal display
216
N.C.
-
Not used
68
XAV-63/63M/64BT/64BTM
SECTION 6
EXPLODED VIEWS
1
7-600-028-44 TAPE, ADHESIVE (ST-854GH) 10X33 m
(See Note 1)
2
2-583-629-21 SHEET, DUST PROTECTION (See Note 1)
PW1
1-839-376-31 CONNECTION CORD FOR AUTOMOBILE
(POWER CORD)
(US, CND, E (NTSC), E (PAL), EA, MX (XAV-63))
PW1
1-839-626-11 CONNECTION CORD (ISO) (POWER CORD)
(AEP, RU, UK)
PW1
1-846-441-11 CONNECTION CABLE FOR AUTOMOBILE
(POWER CORD) (XAV-63M/64BTM)
PW1
1-848-694-11 CABLE, CONNECTION (MMC) (Connection cord
Only for MITSUBISHI MOTORS car dealer option)
(XAV-64BT: MX)
#1
7-685-792-01 SCREW +PTT 2.6X6 (S)
#6
7-627-552-87 SCREW, PRECISION +P 1.7X2.2 (See Note 1)
#7
7-685-791-01 SCREW +PTT 2.6X5 (S)
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
Parts Color Cabinet’s Color
• Abbreviations
CND : Canadian model
EA
CND : Canadian model
EA
: Saudi Arabia model
IND
: Indian model
MX
: Mexican model
RU
: Russian model
6-1. OVERALL SECTION
The components identifi ed by mark
0
or dotted line with mark
0 are critical for
safety.
Replace only with part number specifi ed.
Replace only with part number specifi ed.
Les composants identifi és par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce por-
tant le numéro spécifi é.
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce por-
tant le numéro spécifi é.
front panel section
chassis section
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
#1
#1
#1
#1
#1
#1
#1
#1 (for MG-614E-189)
#7 (for MG-613XE-187)
#7 (for MG-613XE-187)
#6
PW1
DVD mechanism deck section
(MG-613XE-187)
(MG-613XE-187)
#1
not supplied
(XAV-64BT/64BTM)
(See Note 1)
(XAV-64BT/64BTM)
(XAV-64BT/64BTM)
F
G
H
H
G
2
1
1
F
Ver. 1.6
Note 2: Adhesive (ST-854GH) 10
33 m tape cannot re-used.
Please replace to brand-new part ones adhesive (ST-
854GH) 10
854GH) 10
33 m tape is removed.
Note 1: These parts are deleted from
the midway of production.
Note 3: Refer to SUPPLEMENT-2 for discrim-
ination of the DVD mechanism deck
(MG-613XE-187 or MG-614E-189).
(MG-613XE-187 or MG-614E-189).
• The installation parts of only for MITSUBISHI
MOTORS car dealer option of XAV-64BT (Mexi-
can model), refer to service manual SUPPLE-
MENT-3.
can model), refer to service manual SUPPLE-
MENT-3.
Click on the first or last page to see other XAV-63 / XAV-63M / XAV-64BT / XAV-64BTM service manuals if exist.