Sony MEX-N4100BE / MEX-N4100BT / MEX-N4150BT Service Manual ▷ View online
MEX-N4100BE/N4100BT/N4150BT
21
7
Rear speaker
(left)
(left)
È Green
8
¾ Green/black
striped
(E, Saudi Arabia, Argentina, Indian and Australian models)
Cautions
ˎ Run all ground (earth) leads to a common
ground (earth) point.
ˎ Do not get the leads trapped under a screw, or
caught in moving parts (e.g., seat railing).
ˎ Before making connections, turn the car ignition
off to avoid short circuits.
ˎ Connect the yellow and red power supply leads
only after all other leads have been connected.
For Argentine models: Connect the power supply
lead
For Argentine models: Connect the power supply
lead
ʙ to the unit and speakers before
connecting it to the auxiliary power connector.
ˎ Be sure to insulate any loose unconnected leads
with electrical tape for safety.
ˎ Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
operations.
ˎ Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature,
such as in direct sunlight or near heater ducts.
such as in direct sunlight or near heater ducts.
ˎ Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
circuit to which the unit is connected must be higher
than the sum of each component’s fuse amperage
rating.
rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connection/Installation
Precautions
Connection
(For MEX-N4150BT)
*1 Not supplied
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
wired remote control (not supplied).
*5 Whether in use or not, route the microphone input
cord such that it does not interfere with driving
operations. Secure the cord with a clamp, etc., if it is
installed around your feet.
installed around your feet.
*6 AUDIO OUT can be switched to SUB or REAR.
*7 Note for the antenna (aerial) connecting (Argentine
*7 Note for the antenna (aerial) connecting (Argentine
models only):
If your car antenna (aerial) is an ISO (International
Organization for Standardization) type, use the
Organization for Standardization) type, use the
supplied adaptor
ͭ to connect it.
ͬ
from a wired remote control
(not supplied)*
(not supplied)*
4
White
White/black striped
Gray
Gray
Black
Yellow
Red
Blue/white striped (MAX 0.4A)
Yellow
Red
Blue/white striped (MAX 0.4A)
Front speaker*
1
*
2
Rear speaker*
1
*
2
Gray/black striped
Green
Green/black striped
Purple
Purple
Purple/black striped
*
3
*
3
Subwoofer*
1
Power amplifier*
1
For details, see “Making
connections” (page 32).
connections” (page 32).
*
6
from a car antenna (aerial)*
7
ͭ
For Argentine models
*
2
ʙ
Microphone
XA-MC10*
XA-MC10*
1
*
5
See “Power connection diagram (Argentine models
only)” (page 33) for details.
only)” (page 33) for details.
ɞ To a common ground (earth) point
First connect the black ground (earth) lead, then
connect the yellow and red power supply leads.
connect the yellow and red power supply leads.
ɟ To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
ɠ To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
Making connections
For Argentine models:
If you have a power antenna (aerial) without a relay
box, connecting this unit with the supplied power
supply lead
box, connecting this unit with the supplied power
supply lead
ͬ may damage the antenna (aerial).
ɣ To the car’s speaker connector
1
Rear speaker
(right)
(right)
È Purple
2
¾
Purple/black
striped
striped
3
Front speaker
(right)
(right)
È Gray
4
¾ Gray/black striped
5
Front speaker
(left)
(left)
È White
6
¾
White/black
striped
striped
g
( g
for details.
ɡ To the power antenna (aerial) control lead or
the power supply lead of the antenna (aerial)
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
MEX-N4100BE/N4100BT/N4150BT
22
2
Insert both release keys
ͧ until they
click, and pull down the bracket
ʓ, then
pull up the unit to separate.
Before installing, make sure the catches on both
sides of the bracket
sides of the bracket
ʓ are bent inwards 2 mm (
3
/
32
in). When mounting in a Japanese car, see
“Mounting the unit in a Japanese car” (page 34).
“Mounting the unit in a Japanese car” (page 34).
1
Position the bracket
ʓ inside the
dashboard, then bend the claws outward
for a tight fit.
for a tight fit.
Mounting the unit in the dashboard
ʓ
ͧ
Face the hook inwards.
ʓ
182 mm (7
1
/
4
in)
53 mm (2
1
/
8
in)
Catch
ɤ To the car’s power connector
Subwoofer Easy Connection
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
when it is connected to a rear speaker cord.
Notes
ˎ Preparation of the rear speaker cords is required
(Argentine models only).
ˎ Use a subwoofer with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
Speaker connection
ˎ Before connecting the speakers, turn the unit off.
ˎ Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
avoid damage.
12
continuous power
supply
supply
Yellow
13
power antenna (aerial) /
power amplifier control
(REM OUT)
power amplifier control
(REM OUT)
Blue/white striped
15 switched power supply
Red
16 ground (earth)
Black
Front speaker
Subwoofer
1
To enable the wired remote control, set
[STR CONTROL] in [SET STEERING] to
[EXTERNAL] (page 17).
[STR CONTROL] in [SET STEERING] to
[EXTERNAL] (page 17).
Using the wired remote control
Make sure your car’s auxiliary power connector, and
match the connections of cords correctly
depending on the car.
match the connections of cords correctly
depending on the car.
Common connection
When the positions of the red and yellow
leads are inverted
Power connection diagram (Argentine
models only)
models only)
12
continuous power
supply
supply
Yellow
15 switched power supply Red
12 switched power supply Yellow
15
continuous power
supply
supply
Red
Auxiliary power connector
Red
Red
Yellow
Yellow
Red
Red
Yellow
Yellow
.
Installation
Before installing the unit, remove the protection
collar
collar
ͨ and the bracket ʓ from the unit.
1
Pinch both edges of the protection collar
ͨ, then pull it out.
Removing the protection collar and the
bracket
bracket
ͨ
2
Mount the unit onto the bracket
ʓ, then
attach the protection collar
ͨ.
Notes
ˎ If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
ˎ Make sure the 4 catches on the protection collar ͨ
are properly engaged in the slots of the unit.
Mounting the unit in a Japanese car
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult your
Sony dealer.
makes of Japanese cars. In such a case, consult your
Sony dealer.
TOYOTA
ʓ
ͨ
ͩ
ͪ
ͫ
to dashboard/center console
Existing parts supplied with
your car
your car
ͫ
Bracket
Bracket
.
Note
To prevent malfunction, install only with the supplied
To prevent malfunction, install only with the supplied
screws
ͫ.
When the car without ACC position
After matching the connections and switching
power supply leads correctly, connect the unit to
the car’s power supply. If you have any questions
and problems connecting your unit that are not
covered in this manual, consult the car dealer.
power supply leads correctly, connect the unit to
the car’s power supply. If you have any questions
and problems connecting your unit that are not
covered in this manual, consult the car dealer.
Red
Red
Yellow
Yellow
NISSAN
ͫ
to dashboard/center console
Existing parts supplied with
your car
your car
ͫ
Bracket
Bracket
When replacing the fuse, be sure
to use one matching the
amperage rating stated on the
original fuse. If the fuse blows,
check the power connection and
replace the fuse. If the fuse blows
again after replacement, there
may be an internal malfunction. In such a case,
consult your nearest Sony dealer.
to use one matching the
amperage rating stated on the
original fuse. If the fuse blows,
check the power connection and
replace the fuse. If the fuse blows
again after replacement, there
may be an internal malfunction. In such a case,
consult your nearest Sony dealer.
Fuse replacement
Fuse (10 A)
MEX-N4100BE/N4100BT/N4150BT
23
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
3-2. MINI FUSE (BLADE TYPE) (10A/32V) (FU1),
COVER
(Page
COVER
(Page
23)
3-4. SUB PANEL COMPLETE ASSY
(Page
(Page
25)
3-3. CD MECHANISM DECK (MG-101CF-188)
(Page
(Page
24)
3-5. ANTENNA BT (BT1)
(Page
(Page
25)
3-6. MAIN
BOARD
(Page
26)
SET
FRONT PANEL SECTION
Note: Illustration of disassembly is omitted.
Note: Illustration of disassembly is omitted.
3-7. SERVICE
POSITION
(Page
27)
Note: Follow the disassembly procedure in the numerical order given.
3-2. MINI FUSE (BLADE TYPE) (10A/32V) (FU1), COVER
3 three claws
2 two bosses
4 cover
2 two bosses
1 mini fuse (blade type) (10A/32V)
(FU1)
(FU1)
Boss is unlocked.
Boss is locked.
OK
NG
Note: When installing the cover, check
that four bosses are all locked.
MEX-N4100BE/N4100BT/N4150BT
24
3-3. CD MECHANISM DECK (MG-101CF-188)
1 two screws
(PTT2.6
(PTT2.6
u 6)
cable flexible flat
(27 core) (FFC1)
(27 core) (FFC1)
Insert is straight to the interior.
OK
connector
cable flexible flat
(27 core) (FFC1)
(27 core) (FFC1)
Connector is unlock.
NG
connector
cable flexible flat
(27 core) (FFC1)
(27 core) (FFC1)
Insert is incline
NG
connector
cable flexible flat
(27 core) (FFC1)
(27 core) (FFC1)
Insert is shallow
NG
connector
Note 3: When installing the cable flexible flat (27 core) (FFC1), insert straight to the connector and lock a connector completely.
No slanting after insertion.
3 connector
(CN701)
1 screw
(PTT2.6
(PTT2.6
u 6)
5 two screws
(PTT2.6
(PTT2.6
u 4)
slot
slot
Note 2: When installing the CD mechanism block,
align the rib and the slot.
1 screw
(PTT2.6
(PTT2.6
u 6)
2 Lift up the CD mechanism
block in the direction of
the
arrow.
Note 2: When installing the
CD mechanism block,
align the rib and
the
slot.
6 bracket (CD)
4 cable flexible flat (27 core)
(FFC1)
(FFC1)
(CN401)
1 cable flexible flat
(27
(27
core) (FFC1)
(CN401)
7 CD mechanism deck
(MG-101CF-188)
(MG-101CF-188)
2 cable flexible flat
(27
(27
core) (FFC1)
(CN701)
3
+RZWRLQVWDOO
WKH&'PHFKDQLVPGHFN
WKH&'PHFKDQLVPGHFN
Note 1: The service manual of the mechanism deck, used in this model has been issued in a sepa-
rate volume. Please refer to the service manual of the MG-101 series for the mechanism
deck information.
deck information.
Click on the first or last page to see other MEX-N4100BE / MEX-N4100BT / MEX-N4150BT service manuals if exist.