Sony MEX-DV1600U / MEX-DV1606U / MEX-DV160UE Service Manual ▷ View online
MEX-DV160UE/DV1600U/DV1606U
9
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
SET
3-2. SUB PANEL COMPLETE ASSY
(Page
(Page
9)
3-3. DVD MECHANISM DECK BLOCK
(Page
(Page
10)
3-4. DC FAN (25X25) (M601),
MAIN
MAIN
BOARD
(Page
10)
3-5. SERVO
BOARD
(Page
11)
3-6. CHASSIS (T612Z) SUB ASSY,
SENSOR
SENSOR
BOARD
(Page
11)
3-7. CHASSIS (OP, ZA) COMPLETE ASSY
(Page
(Page
12)
FRONT PANEL SECTION
Note:
Note:
Illustration of disassembly is omitted.
Note: Follow the disassembly procedure in the numerical order given.
3-2. SUB PANEL COMPLETE ASSY
1 screw
(PTT2.6
u 6)
5 two screws
(PTT2.6
u 6)
2 two bosses
2 two bosses
4 cover
6 two claws
3 three claws
6 two claws
7 sub panel complete assy
MEX-DV160UE/DV1600U/DV1606U
10
3-3. DVD MECHANISM DECK BLOCK
3 connector
(CN101)
4 cover (FFC)
5 flexible flat cable (60 core)
(CN10)
6 adhesive (ST-854GH)
10
u 30 m tape
6 adhesive (ST-854GH)
10
u 30 m tape
4 connector
(CN401)
1 screw
(PTT2.6
u 6)
8 two screws
(PTT2.6
u 5)
7 two screws
(P1.7
u 2.2)
9 shield (613)
0 bracket (CD)
qa dust protection sheet
qd DVD mechanism deck block
qs laser caution label
1 screw
(PTT2.6
u 6)
2 Lift up the DVD mechanism deck
(MG-613I-187).
(EXCEPT AEP, UK)
qd MAIN board
5 fuse (blade type) (auto fuse)
(10A/32V)
(FU801)
4 chassis
3 insulating sheet
0 two screws
(PS2.6
u 14)
8 screw
(PTT2.6
u 8)
1 two screws
(PTT2.6
u 8)
9 connection cord (front audio out,
rear/sub audio out, AUX audio in)
qs DC fan (25 u 25)
(M601)
qa connector
(CN802)
7 connector
(CN803)
2 three ground point screws
(PTT2.6
u 6)
6 Lift up the lead pin.
Note2: When the DC fan and MAIN board are mounted,
lock connection cord for auto mobile and wire DC fan
by push lead pin.
3-4. DC FAN (25X25) (M601), MAIN BOARD
Note1: If the complete MAIN board was replaced, be sure to refer to Technical News published separately.
MEX-DV160UE/DV1600U/DV1606U
11
– DVD mechanism deck block (Bottom view) –
3 Remove the three solders
of SENSOR board wire.
3 Remove the two solders
of loading motor wire.
8 SERVO board
SERVO board
SERVO board
RED
WHITE
RED
WHITE
BLACK
6 three screws
(M1.7
u 2.5)
4 OP flexible board
(CN2)
2 wire with connector
(CN7)
5 sled motor flexible board
(CN1)
7
1 adhesive (ST-854GH)
10
u 30 m tape
1 adhesive (ST-854GH)
10
u 30 m tape
1 adhesive (ST-854GH)
10
u 30 m tape
Note: When disconnecting the OP flexible board from
of the connector. Be sure to refer to “NOTE FOR
FLEXIBLE BOARD OF THE OPTICALPICK-UP”
of the servicing notes (See page 4).
3-6. CHASSIS (T612Z) SUB ASSY, SENSOR BOARD
1 two screws
(P1.7
u 2.2)
4 chassis (T612Z) sub assy
1 two screws
(P1.7
u 2.2)
2 claw
3 claw
5 Remove the three solders.
6 SENSOR borad
3-5. SERVO BOARD
MEX-DV160UE/DV1600U/DV1606U
12
3-7. CHASSIS (OP, ZA) COMPLETE ASSY
A
5
1 OP flexible board
(CN2)
6 two coil springs
(damper)
8 chassis (OP, ZA) complete assy
7 compression spring
(damper,
Z)
2 flexible board
(CN1)
3 tension spring (KF)
tension spring (KF)
Method of installing tension spring (KF)
4 Turn the gear (RA1) fully
in the direction of arrow A.
Hang in order of
A, B by pay
attention spring of direction.
A
B
– Bottom view –
Click on the first or last page to see other MEX-DV1600U / MEX-DV1606U / MEX-DV160UE service manuals if exist.