Sony MEX-DV1000 / MEX-DV2000 Service Manual ▷ View online
49
MEX-DV1000/DV2000
Pin No.
Pin Name
I/O
Description
161
VDDHDPLL
-
Power supply terminal (+1.8V)
162
GNDHDPLL
-
Ground terminal
163 to 178
NOT USED
O
Not used
179, 180
GNDDAC_D
-
Ground terminal
181
DAC6 (CVBS)
O
Composite video signal output to the video amplifier
182
VDD_DAC
-
Power supply terminal (+3.3V)
183, 184
DAC5,
DAC4 (DD_A)
O
Video signal output terminal Not used
185
VDD_DAC
-
Power supply terminal (+3.3V)
186, 187
DAC3 (DD_D),
DAC2_LU (DD_B)
O
Video signal output terminal Not used
188
VDD_DAC
-
Power supply terminal (+3.3V)
189
DAC1_CH (DD_C)
O
Video signal output terminal Not used
190
RSET
I
Video D/A converter gain adjustment signal input terminal Not used
191, 192
GNDDACP,
GNDDACBS2
-
Ground terminal
193, 194
RFP, RFN
I
RF signal input from the optical pick-up block
195
G
I
G signal input terminal Not used
196
A
I
A signal input from the optical pick-up block
197
AVDD1_DVDAFE
-
Power supply terminal (+3.3V)
198
B
I
B signal input from the optical pick-up block
199, 200
SVDD_DVDAFE,
AVDD_DVDAFE
-
Power supply terminal (+3.3V)
201
C
I
C signal input from the optical pick-up block
202
H
I
H signal input terminal Not used
203
D
I
D signal input from the optical pick-up block
204
J
I
J signal input terminal Not used
205
AGND_DVDAFE
-
Ground terminal
206
E
I
E signal input from the optical pick-up block
207
K
I
K signal input terminal Not used
208
F
I
F signal input from the optical pick-up block
209
VC
O
Reference voltage (+1.65V) output to the optical pick-up block
210
VBGAP
I
Bandgap reference input terminal
211
RESOUT
O
Internal reference output terminal
212
CD_MD
I
Light amount monitor input from the laser diode of optical pick-up (for CD)
213
DVD_MD
I
Light amount monitor input from the laser diode of optical pick-up (for DVD)
214
CD_LD
O
Laser diode on/of control signal output terminal (for CD) "L": laser diode on
215
DVD_LD
O
Laser diode on/of control signal output terminal (for DVD) "L": laser diode on
216, 217
AGNDREF
_DVDAFE,
_DVDAFE,
AGND1_DVDAFE
-
Ground terminal
218
VDDC
-
Power supply terminal (+1.8V)
219
NOT USED
O
Not used
220
GNDC
-
Ground terminal
221
OP_GAIN
I
Gain control signal input from the optical pick-up block
222
CD_DVD
O
CD/DVD selection signal output terminal "L": CD, "H", DVD
223
VDDP
-
Power supply terminal (+3.3V)
224
NOT USED
O
Not used
50
MEX-DV1000/DV2000
Pin No.
Pin Name
I/O
Description
225
GNDP
-
Ground terminal
226, 227
NOT USED
O
Not used
228
VDDIP
-
Power supply terminal (+3.3V)
229, 230
NOT USED
O
Not used
231
TR_DRV
O
Tracking coil drive signal output terminal
232
NOT USED
O
Not used
233
GNDPWM
-
Ground terminal
234
SP_DRV
O
Spindle motor drive signal output terminal
235
VDDPWM
-
Power supply terminal (+3.3V)
236, 237
STB, STA
O
Sled motor drive signal output terminal
238
FO_DRV
O
Focus coil drive signal output terminal
239
DUPRD0
I
Serial data input terminal Not used
240
DUPTD0
O
Serial data output terminal Not used
241
DUPRD1
I
Serial data input from the system controller
242
DUPTD1
O
Serial data output to the system controller
243
NOT USED
O
Not used
244
DRV_XSTBY
O
Standby signal output to the coil/motor driver and automatic power control circuit
"L": standby
"L": standby
245
VDDP
-
Power supply terminal (+3.3V)
246
FG
I
FG signal input from the coil/motor driver
247
REQ
O
Data communication permission signal output to the system controller
248
EN
I
Data communication request signal input from the system controller
249, 250
NOT USED
O
Not used
251
SSCREQ
O
Request signal output terminal Not used
252
SSCEN
I
Enable signal input terminal Not used
253 to 255
NOT USED
O
Not used
256
GNDP
-
Ground terminal
51
MEX-DV1000/DV2000
MAIN BOARD IC501 M3062LFGPGP (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
FSW_IN
I
Oscillation frequency count signal input from the DC/DC converter
2
FAN
O
Fan motor drive signal output terminal "H": fan motor on
3
DISP_SO
O
Serial data output to the fluorescent indicator tube
4
DISP_SI
I
Serial data input from the fluorescent indicator tube
5
DISP_CKO
O
Serial data transfer clock signal output to the fluorescent indicator tube
6
BYTE
I
Connected with the ground (fixed at "L")
7
FLASH_W
I
Input terminal for the flash writing "L": normally operation mode, "H": writing mode
8
XCIN
I
Low-speed system clock input terminal (32.768 kHz)
9
XCOUT
O
Low-speed system clock output terminal (32.768 kHz)
10
RESET
I
System reset signal input from the reset signal generator and RESET switch "L": reset
For several hundreds msec. after the power supply rises, "L" is input, then it change to "H"
For several hundreds msec. after the power supply rises, "L" is input, then it change to "H"
11
XOUT
O
High-speed system clock output terminal (6 MHz)
12
VSS
-
Ground terminal
13
XIN
I
High-speed system clock input terminal (6 MHz)
14
VCC
-
Power supply terminal (+3.3V)
15
NMI
I
Non-maskable interrupt signal input terminal Not used (fixed at "H")
16
TESTIN
I
Test mode detection signal input terminal
17
DAVN
I
RDS data block synchronizing detection signal input from the RDS decoder
(DV1000: AEP, UK and Russian/DV2000: Russian models only)
(DV1000: AEP, UK and Russian/DV2000: Russian models only)
18
TUNATTIN
I
Attenuation request signal input from the tuner unit
19
NSMASK
O
Tuner noise mask control signal output terminal
(DV1000: AEP, UK and Russian/DV2000: Russian models only)
(DV1000: AEP, UK and Russian/DV2000: Russian models only)
20
BEEP
O
Beep sound output to the power amplifier
21
TUNATT
O
Tuner muting on/off control signal output to the tuner unit "L": muting on
22
EESIO
I/O
EEPROM data bus with the EEPROM and tuner unit
23
EECKO
O
EEPROM clock signal output to the EEPROM and tuner unit
24 to 26
NC
O
Not used
27
I2CCKO
O
I2C clock signal output to the RDS decoder, audio processor, power amplifier and tuner unit
28
I2CSIO
I/O
I2C data bus with the RDS decoder, audio processor, power amplifier and tuner unit
29
E_VOL_SO/TX
O
Serial data output to the electrical volume
Transmission data output to the connector for flash writing
Transmission data output to the connector for flash writing
30
E_VOL_CS/RX
I/O
Chip select signal output to the electrical volume "L" active
Receive data input from the connector for flash writing
Receive data input from the connector for flash writing
31
E_VOL_CKO
O
Serial data transfer clock signal output to the electrical volume
32
SA_CLK
O
Spectrum analyzer data transfer clock signal output to the audio processor
33
MSTR_TX
O
Serial data output to the DVD processor
34
MSTR_RX
I
Serial data input from the DVD processor
35
NC
O
Not used
36
M_RTS
I
Data communication permission signal input from the DVD processor
37
M_CTS
O
Data communication request signal output to the DVD processor
38
NC
O
Not used
39
HOLD
I
External data bus terminal (fixed at "L")
40
OPEN_MUTE
O
Line muting on/off control signal output terminal "H": muting on
41
NC
O
Not used
42
ATT
O
System muting control signal output terminal "H": muting on
43
NC
O
Not used
44
WRI/WR
I
External data bus terminal (fixed at "H")
52
MEX-DV1000/DV2000
Pin No.
Pin Name
I/O
Description
45
DIAG
I
Diagnostic signal input from the power amplifier
46
STB
O
Power supply on/off control signal output terminal for RDS section "H": power on
(DV1000: AEP, UK and Russian/DV2000: Russian models only)
Standby signal output to the power amplifier "L": standby, "H": power amplifier on
(DV1000: AEP, UK and Russian/DV2000: Russian models only)
Standby signal output to the power amplifier "L": standby, "H": power amplifier on
47
NC
O
Not used
48
VOL_ATT
O
Volume muting on/off control signal output to the audio processor "L": muting on
49
NC
O
Not used
50
M_RESET
I
Reset signal output to the DVD processor and flash memory "L": reset
51
SELFSW
I
Self loading position detection switch input terminal
52
INSW
I
Disc insert detection switch input terminal
53
DSW
I
Chucking end detection switch input terminal
54
A_MUTE
I
Analog muting on/off control signal input from the DVD processor "H": muting on
55
VMUTE_R
O
Rear video muting on/off control signal output to the video amplifier "L": muting on
(DV2000 model only)
(DV2000 model only)
56
VMUTE_F
O
Front video muting on/off control signal output to the video amplifier "L": muting on
57 to 59
DSTSEL0 to
DSTSEL2
I
Input terminal for the destination setting
60
VCC
-
Power supply terminal (+3.3V)
61
MODEL_SEL
I
Input terminal for the model setting "L": DV2000 model, "H": DV1000 model
62
VSS
-
Ground terminal
63
NC
O
Not used
64
ILLIN
I
Illumination line detection signal input terminal for the automatic dimmer control
"L": dimmer on (DV2000 model only)
"L": dimmer on (DV2000 model only)
65
RC_IN1
I
Rotary commander shift key input terminal
66
TELATT
I
Telephone muting detection signal input terminal
At input of "H", the audio signal is attenuated by 20 dB (DV2000 model only)
At input of "H", the audio signal is attenuated by 20 dB (DV2000 model only)
67
PARKING
I
Side brake (parking brake) position detection signal input terminal "L": brake on
68
ACCIN
I
Accessory power detection signal input terminal "L": accessory power on
69
FL_ON
O
Power supply on/off control signal output terminal for fluorescent indicator tube
"H": power on
"H": power on
70
FSW_OUT
O
Frequency selection signal output to the DC/DC converter
71
LOAD
O
Loading motor drive signal (loading direction) output terminal
72
EJECT
O
Loading motor drive signal (eject direction) output terminal
73
BU_IN
I
Back up power supply detection signal input from the SONY bus interface
"L" is input at low voltage
"L" is input at low voltage
74
3.3V_ON
O
Power supply on/off control signal output to the DC/DC converter for +3.3V power supply
"H": power on
"H": power on
75
Z_MUTE
I
Muting on/off control signal input from the D/A converter "H": muting on
76
BUS_ON
O
SONY bus on/off control signal output to the SONY bus interface "L": bus on
77
SYSRST
O
Reset signal output to the SONY bus interface "L": reset
78
NOSE_SW
I
Front panel detaching/attaching detection signal input terminal
"L": front panel is attached
"L": front panel is attached
79
SA_IN
I
Spectrum analyzer data input from the audio processor (A/D input)
80
TEMP
I
Temperature detection signal input terminal for fan motor control (A/D input)
81
NC
O
Not used
82
QUALITY
I
Tuner noise detection signal input from the tuner unit (A/D input)
83
VSM
I
FM and AM signal-meter voltage detection signal input from the tuner unit (A/D input)
84, 85
KEYIN0,
KEYIN1
I
Front panel key input terminal (A/D input)
Click on the first or last page to see other MEX-DV1000 / MEX-DV2000 service manuals if exist.