Sony MEX-BT2900 / MEX-BT2950 Service Manual ▷ View online
MEX-BT2900/BT2950
17
3-9. CHASSIS (OP) ASSY
3-10. CHUCKING ARM SUB ASSY
6 two coil springs (damper) (natural)
7 coil spring (damper) (green)
8 chassis (OP) assy
5
1 tension spring (KF)
2 gear (LE1)
3 lever (D)
4 slider (R)
3 chucking arm sub assy
2
1 spring
Note 1: Have this portion receive the chassis.
Note 1: Have this portion receive the chassis.
Note 2: Be careful not to touch the turn table.
MEX-BT2900/BT2950
18
3-11. SLED MOTOR ASSY
3 sled motor assy
sled motor assy
1 spring
spring
stand
stand
turn table
2 three serration screws
(M 2
u 3)
three serration screws
(M 2
u 3)
bearing (F)
bearing (R)
Note 1: Place the stand with care not to touch the turn table.
Note 2: Never remove these parts since they were adjusted.
Note 3: Take care to prevent the chassis from being bent
when tightening the three machine screws.
1RWHIRU$VVHPEO\
–
ERWWRPVLGHYLHZ
–
–
ERWWRPVLGHYLHZ
–
–
ERWWRPVLGHYLHZ
–
MEX-BT2900/BT2950
19
3-12. OPTICAL PICK-UP SECTION
3-13. OPTICAL PICK-UP
1
2 optical pick-up section
Note: Be careful not to touch the lens and hologram
terminal when removing the optical pick-up section.
–
bottom side view
–
There is space at the end of the
leaf spring (sub guide) to avoid
contact with the slide.
leaf spring (sub guide) to avoid
contact with the slide.
1 pan tapping screw
(M 1.4
u 2.5)
2 leaf spring (sub guide)
3 leaf spring (OP)
5 optical pick-up
4 lead screw assy
Prevent the end of the
leaf spring (sub guide) from being
in contact with the OP slide base.
leaf spring (sub guide) from being
in contact with the OP slide base.
Prevent the end of the
leaf spring (sub guide) from being
in contact with the OP slide base.
leaf spring (sub guide) from being
in contact with the OP slide base.
–
bottom side view
–
Notes for Assembly
MEX-BT2900/BT2950
20
SECTION 4
TEST MODE
SETTING THE TEST MODE
Setting method:
1. Press the [SOURCE/OFF] button for 1 second to turn the pow-
1. Press the [SOURCE/OFF] button for 1 second to turn the pow-
er off.
2. Press the [4]
→ [5] → [1] buttons sequentially (the [1] button
is pressed for two seconds).
3. It is set to the test mode, and all segments of the liquid crystal
display light.
Releasing method:
Press the [SOURCE/OFF] button for 1 second.
Press the [SOURCE/OFF] button for 1 second.
MICROPHONE AUDIO LOOPBACK
To confi rm the state of the external microphone/internal micro-
phone used when a handsfree function is used, the microphone
audio is output from the speaker.
The breakdown judgment of the microphone can be done without
connecting H/F with the cellular phone.
To confi rm the state of the external microphone/internal micro-
phone used when a handsfree function is used, the microphone
audio is output from the speaker.
The breakdown judgment of the microphone can be done without
connecting H/F with the cellular phone.
Procedure:
1. Enter the test mode.
2. Press the [SOURCE/OFF] button to select the Bluetooth Phone
1. Enter the test mode.
2. Press the [SOURCE/OFF] button to select the Bluetooth Phone
function.
3. On/off of the microphone audio loopback function changes
whenever the [2] button is pressed (“ALBM” is displayed in
the liquid crystal display).
the liquid crystal display).
LOOP BACK
ALBM
ON
Lit
OFF
None
Click on the first or last page to see other MEX-BT2900 / MEX-BT2950 service manuals if exist.