Sony MDX-66XLP Service Manual ▷ View online
9
MDX-66XLP
3-7. SERVO BOARD
3-6. CHASSIS (OP) BLOCK
4
bearing (ELV)
7
bearing (ELV)
9
worm wheel (ELV2)
6
chassis (OP) block
3
chassis (bottom) assy
1
precision screw
(P 1.7x1.8)
2
precision
three screws
(P 1.7x1.8)
(P 1.7x1.8)
5
bearing (ELV)
8
bearing (ELV)
1
CN200
6
CN100
5
CN300
4
CN400
3
three screws
(M1.7x2.2)
7
SERVO board
2
Unsolder the
motor lead wires.
10
MDX-66XLP
3-8. OPTICAL PICK-UP
1
two screws
(K1.7x3.5)
2
optical pick-up
11
MDX-66XLP
3-9. NOTE ON ASSEMBLY FOR THE CHASSIS (OP) BLOCK
A
B
B
B
A
A
2
Turn the three feed
screw (ELV) assy fully in
the direction of arrows
the direction of arrows
A
.
qa
Turn the three gear (ELVB) fully
in the direction of arrows
B
.
6
bearing (ELV)
7
bearing (ELV)
0
precision
three screws
(P1.7x1.8)
(P1.7x1.8)
9
precision screw
(P1.7x1.8)
8
chassis (bottom) assy
5
chassis (OP) block
3
bearing (ELV)
4
bearing (ELV)
1
worm wheel (ELV2)
qf
gear (ELVC)
qs
gear (ELVA2)
qg
polyethylene washer
qd
polyethylene washer
12
MDX-66XLP
4-1. IC PIN DESCRIPTIONS
• IC100 CXA2523AR (RF AMP)
Pin No.
Pin Name
I/O
Pin Description
1
I
I
I-V converted RF signal input (I) from detector of optical pick-up
2
J
I
I-V converted RF signal input (J) from detector of optical pick-up
3
VC
O
Center voltage (+1.65 V) generation output
4 – 9
A – F
I
Signal input (A to F) from detector of optical pick-up
10
PD
I
Quantity monitor input of light from laser diode of optical pick-up
11
APC
O
Laser amplifier output to automatic power control circuit
12
APCREF
I
Reference voltage input for laser power setting
13
GND
—
Ground pin
14
TEMPI
I
Temperature sensor connecting pin (Not used in this set.)
15
TEMPR
O
Reference voltage output for temperature sensor (Not used in this set.)
16
SWDT
I
Write data signal input from System controller (IC600)
17
SCLK
I
Serial clock signal input from System controller (IC600)
18
XLAT
I
Serial latch signal input from System controller (IC600)
19
XSTBY
I
Standby signal input (“L” : Standby) (Fixed at “H” in this set.)
20
FOCNT
I
Center frequency control voltage input of internal circuit filter (BPF22, BPF3T and EQ)
21
VREF
O
Reference voltage output (Not used in this set.)
22
EQADJ
I
Center frequency setting input of internal circuit filter (EQ)
23
3TADJ
I
Center frequency setting input of internal circuit filter (BPF3T)
24
VCC
—
Power supply pin (+3.3 V)
25
WBLADJ
I
Center frequency setting input of internal circuit filter (BPF22)
26
TE
O
Tracking error signal output to CXD2662R (IC200)
27
CSLED
I
Connecting pin for low pass filter condenser of sled error signal
28
SE
O
Sled error signal output to CXD2662R (IC200)
29
ADFM
O
FM signal output of ADIP
30
ADIN
I
FM signal input of ADIP by AC combination
31
ADAGC
I
External condenser connecting pin for AGC of ADIP
32
ADFG
O
ADIP double FM signal output (22.05 kHz ± 1 kHz) to CXD2662R (IC200)
33
AUX
O
Support signal (I3 signal/temperature signal) output (Not used in this set.)
34
FE
O
Focus error signal output to CXD2662R (IC200)
35
ABCD
O
Quantity signal output of light to CXD2662R (IC200)
36
BOTM
O
Bottom hold signal output of quantity signal (RF/ABCD) of light to CXD2662R (IC200)
37
PEAK
O
Peak hold signal output of quantity signal (RF/ABCD) of light to CXD2662R (IC200)
38
RF
O
Playback EFM RF signal output to CXD2662R (IC200)
39
RFAGC
I
External condenser connecting pin of AGC circuit for RF
40
AGCI
I
RF signal input by AC combination
41
COMPO
O
User comparator output pin (Not used in this set.)
42
COMPP
I
User comparator input pin (Fixed at “L” in this set.)
43
ADDC
I
External condenser connecting pin for low frequency interception of ADIP amplifier
44
OPO
O
External condenser connect pin for lower cut of ADIP amplifier
45
OPN
I
User operational amplifier inversion input pin (Fixed at “L” in this set.)
46
RFO
O
RF signal output
47
MORFI
I
RF signal input of MO by AC combination
48
MORFO
O
RF signal output of MO
SECTION 4
DIAGRAMS
Click on the first or last page to see other MDX-66XLP service manuals if exist.