Sony DSX-M50BT Service Manual ▷ View online
DSX-M50BT
9
3-3. SUB PANEL BLOCK
3 two claws
3 two claws
2 microphone connector (CN1004)
1 filament tape
USB cover
:LUHVHWWLQJ
$WWDFKPHQWWKHVXESDQHOEORFN
front side
connector
(CN1004)
(CN1004)
4 two claws
5 sub panel block
Note
1: Where USB cover is closed,
remove the sub panel block.
antenna BT
USB cover
OK
NG
close
open
Note 2: Where USB cover is closed, attach the sub panel block.
Antenna BT may be damaged, if it pushes in strongly
where USB cover is opened.
±,QQHUYLHZ±
contact
front side
microphone wire
filament
tape
tape
BT board
MAIN board
DSX-M50BT
10
3-4. MAIN BOARD (WITH BT BOARD)
2 screw
(PTT2.6
u 8)
2 screw
(PTT2.6
u 8)
3 two ground point screws
(PTT2.6
u 6)
4 MAIN board
(with BT board)
BT board
1 lead wire with connector
(CN1006)
:LUHVHWWLQJ
BT board
lead wire with
connector
connector
connector
(CN1006)
(CN1006)
antenna BT
connector
connector
lead wire with connector
lead wire with connector
front side
MAIN board
filament
tape
tape
OK
NG
3-5. ANTENNA BT
1 lead wire with connector
(CN1006)
2 screw (T)
3 antenna BT
:LUHVHWWLQJ
connector
connector
lead wire with connector
lead wire with connector
BT board
lead wire with
connector
connector
connector
(CN1006)
(CN1006)
antenna BT
front side
MAIN board
filament
tape
tape
OK
NG
Note 1: When the complete MAIN board is replaced, it is necessary
to confi rm operation. Refer to “BLUETOOTH FUNCTION
CHECKING METHOD USING A CELLULAR PHONE” on
page 5.
CHECKING METHOD USING A CELLULAR PHONE” on
page 5.
Note 2: When the complete MAIN board is replaced, the destination
setting is necessary. Refer to “NOTE OF REPLACING THE
COMPLETE MAIN BOARD OR SYSTEM CONTROLLER
(IC101)” on page 4.
COMPLETE MAIN BOARD OR SYSTEM CONTROLLER
(IC101)” on page 4.
DSX-M50BT
11
SECTION 4
TEST MODE
SETTING THE TEST MODE
Setting method:
1. In the state of source off (the clock is displayed on the liquid
1. In the state of source off (the clock is displayed on the liquid
crystal display), enter the test mode by pressing the buttons on
the remote commander in order of the [4]
the remote commander in order of the [4]
t [5] t [1] (press
only the [1] button for two seconds).
2. It is set to the test mode, and all segments of the liquid crystal
display light.
Releasing method:
Press the [SOURCE
Press the [SOURCE
OFF] button for 1 second.
MICROPHONE AUDIO LOOPBACK
To confi rm the state of the internal microphone used when a
handsfree function is used, the microphone audio is output from
the speaker.
The breakdown judgment of the microphone can be done without
connecting H/F with the cellular phone.
To confi rm the state of the internal microphone used when a
handsfree function is used, the microphone audio is output from
the speaker.
The breakdown judgment of the microphone can be done without
connecting H/F with the cellular phone.
Procedure:
1. Enter the test mode.
2. Press the [SOURCE
1. Enter the test mode.
2. Press the [SOURCE
OFF] button to select the Bluetooth
Phone function.
3. On/off of the microphone audio loopback function changes
whenever the [ALBUM v 2] button is pressed (“ALBM” is
displayed in the liquid crystal display).
displayed in the liquid crystal display).
LOOP BACK
ALBM
ON
Lit
OFF
None
DSX-M50BT
12
MEMO
Click on the first or last page to see other DSX-M50BT service manuals if exist.