Sony DSX-A200UI / DSX-A202UI Service Manual ▷ View online
DSX-A200UI/A202UI
5
MODEL IDENTIFICATION
Distinguish by Part No. on the bottom side of the main unit.
Distinguish by Part No. on the bottom side of the main unit.
– Bottom view –
(Australian model)
(Australian model)
– Bottom view –
(AEP, Russian and UK models)
(AEP, Russian and UK models)
Part No.
Model Number Label
Part No.
Model Number Label
Part No.
Model
4-576-083-0[]
DSX-A200UI: AEP and UK models (EUR)
4-576-084-0[]
DSX-A202UI: AEP and UK models (EUR)
4-576-086-0[]
DSX-A202UI: Russian model (RU2)
4-576-087-0[]
DSX-A200UI: Australian model (ET4)
NOTE OF REPLACING THE KEY BOARD
When the KEY board is defective, replace the FRONT PANEL
OVERALL ASSY (Ref. No. FP1).
When the KEY board is defective, replace the FRONT PANEL
OVERALL ASSY (Ref. No. FP1).
NOTE OF REPLACING THE IC001, IC602 AND IC1301
ON THE MAIN BOARD
IC001, IC602 and IC1301 on the MAIN board cannot replace
with single. When these parts are damaged, replace the complete
mounted board.
ON THE MAIN BOARD
IC001, IC602 and IC1301 on the MAIN board cannot replace
with single. When these parts are damaged, replace the complete
mounted board.
CHECKING THE OPERATION
When checking the operation of this unit, connect a USB device
to this unit.
Refer to the support site written in the operating instructions for
the details about the compatibility of a USB device.
When checking the operation of this unit, connect a USB device
to this unit.
Refer to the support site written in the operating instructions for
the details about the compatibility of a USB device.
CLEANING THE CONNECTORS
The unit may not function properly if the
connectors between the unit and the front panel
are not clean. In order to prevent this, detach the
front panel (page 6) and clean the connectors with
a cotton swab. Do not apply too much force.
Otherwise, the connectors may be damaged.
connectors between the unit and the front panel
are not clean. In order to prevent this, detach the
front panel (page 6) and clean the connectors with
a cotton swab. Do not apply too much force.
Otherwise, the connectors may be damaged.
Notes
ˎ For safety, turn off the ignition before cleaning the
connectors, and remove the key from the ignition
switch.
switch.
ˎ Never touch the connectors directly with your fingers
or with any metal device.
CANCELING THE DEMO MODE
You can cancel the demonstration display which
appears when the source is off and the clock is
displayed.
appears when the source is off and the clock is
displayed.
1
Press MENU, rotate the control dial to
select [SET GENERAL], then press it.
select [SET GENERAL], then press it.
2
Rotate the control dial to select [SET
DEMO], then press it.
DEMO], then press it.
3
Rotate the control dial to select [SET
DEMO-OFF], then press it.
DEMO-OFF], then press it.
The setting is complete.
4
Press
(back)
twice.
The display returns to normal reception/play
mode.
mode.
and clean the connectors with
DSX-A200UI/A202UI
6
SECTION 2
GENERAL
This section is extracted
from operating instruction.
from operating instruction.
(AEP and UK models)
Cautions
ˎ Run all ground (earth) leads to a common
ground (earth) point.
ˎ Do not get the leads trapped under a screw, or
caught in moving parts (e.g., seat railing).
ˎ Before making connections, turn the car ignition
off to avoid short circuits.
ˎ Connect the power supply lead ʖ to the unit and
speakers before connecting it to the auxiliary
power connector.
power connector.
ˎ Be sure to insulate any loose unconnected leads
with electrical tape for safety.
ˎ Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
operations.
ˎ Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature,
such as in direct sunlight or near heater ducts.
such as in direct sunlight or near heater ducts.
ˎ Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component’s fuse amperage
rating.
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component’s fuse amperage
rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connection/Installation
Precautions
Connection
*1 Not supplied
*2 Speaker impedance : 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*2 Speaker impedance : 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on th e type of ca r, use an adap tor for a
wired remote control (not supplied).
*5 Depending on th e type of ca r, use an adap tor (not
sup plied) if the antenna connector does not fit.
from a wired remote control
(not supplied)*
(not supplied)*
4
See “Power connection diagram”
for details.
from a car antenna (aerial)*
5
*
3
Power amplifier*
1
For details, see “Making
conn ections”.
conn ections”.
*
2
If you have a power antenna (aerial) without a relay
box, connecting this unit with the supplied power
supply lead ʖ may damage the antenna (aerial).
ɞ To the car’s speaker connector
box, connecting this unit with the supplied power
supply lead ʖ may damage the antenna (aerial).
ɞ To the car’s speaker connector
Making connections
1
Rear speaker
(right)
(right)
È Purple
2
¾ Purple/black
striped
3
Front speaker
(right)
(right)
È Gray
4
¾ Gray/black striped
5
Front speaker
(left)
(left)
È White
6
¾ White/black
striped
7
Rear speaker
(left)
(left)
È Green
8
¾ Green/black
striped
ɟ To the car’s power connector
12
continuous power
supply
supply
Yellow
13
power antenna (aerial) /
power amplifier control
(REM OUT)
power amplifier control
(REM OUT)
Blue/white striped
15
switched power supply
Red
16
ground (earth)
Black
Subwoofer Easy Connection
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
when it is connected to a rear speaker cord.
Notes
ˎ Preparation of the rear speaker cords is required.
ˎ Use a subwoofer with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
avoid damage.
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
Speaker connection
ˎ Before connecting the speakers, turn the unit off.
ˎ Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
avoid damage.
Front speaker
Subwoofer
DSX-A200UI/A202UI
7
Make sure your car’s auxiliary power connector, and
match the connections of cords correctly
depending on the car.
match the connections of cords correctly
depending on the car.
Common connection
When the positions of the red and yellow
leads are inverted
leads are inverted
Power connection diagram
12
continuous power
supply
supply
Yellow
15
switched power supply
Red
12
switched power supply Yellow
15
continuous power
supply
supply
Red
Auxiliary power connector
Red
Red
Yellow
Yellow
Red
Red
Yellow
Yellow
Before installing, make sure the catches on both
sides of the bracket ʓ are bent inwards 2 mm (
sides of the bracket ʓ are bent inwards 2 mm (
3
/
32
in).
1
Position the bracket ʓ inside the
dashboard, then bend the claws outward
for a tight fit.
dashboard, then bend the claws outward
for a tight fit.
2
Mount the unit onto the bracket ʓ, then
attach the protection collar ͨ.
attach the protection collar ͨ.
Notes
ˎ If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
ˎ Make sure the 4 catches on the protection collar ͨ
are properly engaged in the slots of the unit.
Mounting the unit in the dashboard
ʓ
182 mm (7
1
/
4
in)
53 mm (2
1
/
8
in)
Catch
ʓ
ͨ
When the car without ACC position
Red
Red
Yellow
Yellow
After matching the connections and switching
power supply leads correctly, connect the unit to
the car’s power supply. If you have any questions
and problems connecting your unit that are not
covered in this manual, consult the car dealer.
power supply leads correctly, connect the unit to
the car’s power supply. If you have any questions
and problems connecting your unit that are not
covered in this manual, consult the car dealer.
Installation
Before installing the unit, remove the protection
collar ͨ and the bracket ʓ from the unit.
collar ͨ and the bracket ʓ from the unit.
1
Pinch both edges of the protection collar
ͨ, then pull it out.
2
Insert both release keys ͧ until they
click, and pull down the bracket ʓ, then
pull up the unit to separate.
click, and pull down the bracket ʓ, then
pull up the unit to separate.
Removing the protection collar and the
bracket
bracket
ͨ
ʓ
ͧ
Face the hook inwards.
When replacing the fuse, be sure
to use one matching the
amperage rating stated on the
original fuse. If the fuse blows,
check the power connection and
replace the fuse. If the fuse blows
again after replacement, there
may be an internal malfunction. In such a case,
consult your nearest Sony dealer.
to use one matching the
amperage rating stated on the
original fuse. If the fuse blows,
check the power connection and
replace the fuse. If the fuse blows
again after replacement, there
may be an internal malfunction. In such a case,
consult your nearest Sony dealer.
Fuse replacement
Fuse (10 A)
DSX-A200UI/A202UI
8
(Australian model)
Cautions
ˎ Run all ground (earth) leads to a common
ground (earth) point.
ˎ Do not get the leads trapped under a screw, or
caught in moving parts (e.g., seat railing).
ˎ Before making connections, turn the car ignition
off to avoid short circuits.
ˎ Connect the yellow and red power supply leads
only after all other leads have been connected.
ˎ Be sure to insulate any loose unconnected leads
with electrical tape for safety.
ˎ Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
operations.
ˎ Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature,
such as in direct sunlight or near heater ducts.
such as in direct sunlight or near heater ducts.
ˎ Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component’s fuse amperage
rating.
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component’s fuse amperage
rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connection/Installation
Precautions
Connection
*1 Not supplied
*2 Speaker impedance : 4 – 8 Ω × 4
*2 Speaker impedance : 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
*4 Depending on the type of car, use an adaptor for a
wired remote control (not supplied).
White
White/black striped
Gray
Black
Ye llow
Red
Blue /white striped
Front speaker*
1
*
2
Rear speaker*
1
*
2
Gray /black striped
Green
Green /black striped
Purple
Purple/ black striped
*
3
Power amplifier*
1
For details, see “Making
connections”.
connections”.
froma car antenna (aerial)
from a wired remote control
(not supplied)*
(not supplied)*
4
ɞ To a common ground (earth) point
First connect the black ground (earth) lead, then
connect the yellow and red power supply leads.
connect the yellow and red power supply leads.
ɟ To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
ɠ To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
ɡ To the power antenna (aerial) control lead or
the power supply lead of the antenna (aerial)
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
Making connections
Subwoofer Easy Connection
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
when it is connected to a rear speaker cord.
Note
Use a subwoofer with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to avoid
damage.
Use a subwoofer with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to avoid
damage.
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
Speaker connection
ˎ Before connecting the speakers, turn the unit off.
ˎ Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
avoid damage.
Front speaker
Subwoofer
Installation
Before installing the unit, remove the protection
collar ͨ and the bracket ʓ from the unit.
collar ͨ and the bracket ʓ from the unit.
1
Pinch both edges of the protection collar
ͨ, then pull it out.
2
Insert both release keys ͧ until they
click, and pull down the bracket ʓ, then
pull up the unit to separate.
click, and pull down the bracket ʓ, then
pull up the unit to separate.
Removing the protection collar and the
bracket
bracket
ͨ
ʓ
ͧ
Face the hook inwards.
Click on the first or last page to see other DSX-A200UI / DSX-A202UI service manuals if exist.