Sony CDX-T68X Service Manual ▷ View online
CDX-T68X
5
• This set can be disassembled in the order shown below.
2-1.
DISASSEMBLY FLOW
SECTION 2
DISASSEMBLY
Note 1: The process described in can be performed in any order.
Note 2: Without completing the process described in , the next process can not be performed.
2-2. FRONT PANEL (S) ASSY, CASE (UPPER S)
(Page 6)
2-3. MECHANISM DECK (MG-276A-159)
(Page 6)
2-5. BELT (TS)
(Page 7)
2-4. JACK BOARD
(Page 7)
2-6. MAIN BOARD
(Page 8)
2-10. RF BOARD
(Page 10)
2-13. CHASSIS (EV) ASSY
(Page 11)
2-12. OPTICAL PICK-UP
(KSS-720A)
(Page 11)
(Page 11)
2-14. LEVER (CHK.L) ASSY,
LEVER (CHK.R) ASSY
(Page 12)
(Page 12)
2-15. CHASSIS (OP) BLOCK SERVICE ASSY
(Page 12)
2-9. LE MOTOR ASSY
(CHUCKING)
(M103)
(Page 9)
(M103)
(Page 9)
2-11. SLED MOTOR
COMPLETE ASSY
(M101)
(Page 10)
(M101)
(Page 10)
2-7. ESCUTCHEON (S),
SLIDE VARIABLE RESISTOR
(ELEVATOR HEIGHT SENSOR)
(RV301)
(Page 8)
(ELEVATOR HEIGHT SENSOR)
(RV301)
(Page 8)
2-8. MD MOTOR ASSY
(ELEVATOR)
(M104)
(Page 9)
(M104)
(Page 9)
SET
CDX-T68X
6
2-3.
MECHANISM DECK (MG-276A-159)
Note:
Follow the disassembly procedure in the numerical order given.
2-2.
FRONT PANEL (S) ASSY, CASE (UPPER S)
4
case (upper S)
3
screw
(PTT2.6
(PTT2.6
×
6)
3
screw
(PTT2.6
(PTT2.6
×
6)
1
screw
(PTT2.6
(PTT2.6
×
6)
1
screw
(PTT2.6
(PTT2.6
×
6)
2
front panel (S) assy
5
lever (FLT. 838)
5
lever (FLT. 838)
4
mechanism deck
(MG-276A-159)
(MG-276A-159)
3
jack flexible board
(CN901)
(CN901)
2
spring (FLT S)
2
spring (FLT S)
1
two dampers (S)
1
two dampers (S)
CDX-T68X
7
2-4.
JACK BOARD
2-5.
BELT (TS)
2
screw (FP)
5
cord (with connector)
(BUS/RCA)
(BUS/RCA)
4
ground point screw
(PTT2.6
(PTT2.6
×
6)
3
jack board
1
Remove ten solders
of the cord (with connector).
of the cord (with connector).
3
two screw (FP)
4
rack (UD)
belt (TS)
1
screw
(M1.7
(M1.7
×
2.2)
2
3.5 washer
5
belt (TS)
CDX-T68X
8
1
main flexible board
(CN101)
(CN101)
2
Remove three solders
of the slide variable resistor (RV301).
of the slide variable resistor (RV301).
2
Remove two solders
of the elevator motor
lead wires (M104).
of the elevator motor
lead wires (M104).
3
three screws (FP)
4
main board
2-6.
MAIN BOARD
2-7.
ESCUTCHEON (S), SLIDE VARIABLE RESISTOR (ELEVATOR HEIGHT SENSOR) (RV301)
4
slide variable resistor
(elevator height sensor)
(RV301)
(elevator height sensor)
(RV301)
slide variable resistor
(elevator height sensor)
(RV301)
(elevator height sensor)
(RV301)
2
claw
1
screw (FP)
3
escutcheon (S)
2
three claws
2
three claws
Click on the first or last page to see other CDX-T68X service manuals if exist.