Sony CDX-R5515X / CDX-R5610 / CDX-R6550 Service Manual ▷ View online
5
CDX-R5515X/R5610/R6550
SECTION 1
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
• LOCATION OF CONTROLS
• CDX-R5515X
6
Location of controls and basic operations
Main unit
OPEN/CLOSE shutter opened
Card remote commander
RM-X151
RM-X151
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
A
Volume +/– button
To adjust volume.
B
ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
again.
C
DSPL (display) button 4, 8, 12
To change display items.
D
SEL (select) button 4, 9, 10, 12
To select items.
E
Display window
F
EQ3 (equalizer) button 2, 9
To select an equalizer type (XPLOD,
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
CDX-R5515X
DSPL
SEEK
ATT
OFF
SEL
DSO
OPEN/CLOSE
EQ3
SOURCE
MODE
LIST
SENS
BBE MP
SHUF
REP
CAT
GP/DISC +
-
BTM
6
5
4
3
2
1
1 2
3 4
6
7 8
9
qj
qh
qg
qf
qd
qs
qa
0
5
qk
DSPL
SEEK
ATT
OFF
SEL
DSO
OPEN/CLOSE
EQ3
PTY
SENS
LIST
BTM
BBE MP
SHUF
REP
GP/DISC
+
-
AF/TA
6
5
4
3
2
1
SOURCE
MODE
ql
w;
OFF
DSPL
SCRL
SEL
SOURCE
MODE
1
3
2
4
6
5
ATT
VOL
+
–
+
–
2
3
8
qa
qs
4
wf
wa
ws
wg
wd
7
G
DSO button 2
To select the DSO mode (1, 2, 3 or OFF).
The larger the number, the more enhanced
the effect.
The larger the number, the more enhanced
the effect.
H
OFF button
To power off/stop the source.
I
SEEK +/– button
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
J
(front panel release) button 4
K
SOURCE button
To power on/change the source (Radio/CD/
MD*
MD*
1
).
L
MODE button 8, 11
To select the radio band (FM/AM)/select the
unit*
unit*
2
.
M
RESET button
(located behind the front
panel)
4
N
Number buttons
Radio:
To receive stored stations (press); store
stations (press and hold).
CD/MD*
To receive stored stations (press); store
stations (press and hold).
CD/MD*
1
:
(1)/(2):
GP
*
3
/
DISC
*
2
–/+
To skip groups (press); skip groups
continuously (press and hold).
(3):
continuously (press and hold).
(3):
REP 8
(4):
SHUF 8
(5):
BBE MP 3
To activate the BBE MP function, to set
“BBEMP-ON” during playback on this unit.
To cancel, set “BBEMP-OFF.”
“BBEMP-ON” during playback on this unit.
To cancel, set “BBEMP-OFF.”
O
BTM button 8
To start the BTM function.
P
SENS button
To improve weak reception: LOCAL/
MONO.
MONO.
Q
LIST/CAT button 9, 11
To list up.
R
Receptor for the card remote
commander
commander
S
Disc slot 5
T Z
(eject) button 6
The following buttons on the card remote
commander have also different buttons/functions
from the unit.
commander have also different buttons/functions
from the unit.
wa <
(
.
)/
,
(
>
) buttons
To control radio/CD, the same as (SEEK)
+/– on the unit. (For details of other
operations, see “With the card remote
commander” on each pages.)
+/– on the unit. (For details of other
operations, see “With the card remote
commander” on each pages.)
ws
VOL +/– button
To adjust volume.
wd M
(+)/
m
(–) buttons
To control CD, the same as (1)/(2) –/+ on
the unit. (For details of other operations, see
“With the card remote commander” on each
pages.)
the unit. (For details of other operations, see
“With the card remote commander” on each
pages.)
wf
SCRL button 8
To scroll the display item.
wg
Number buttons
To receive stored stations (press); store
stations (press and hold).
stations (press and hold).
*1
When an MD changer is connected.
*2
When a CD/MD changer is connected.
*3
When an MP3/ATRAC CD is played and a changer
is not connected. If the changer is connected, the
operation is different, see page 11.
is not connected. If the changer is connected, the
operation is different, see page 11.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless
(SOURCE)
on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 14.
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 14.
6
Location of controls and basic operations
Main unit
OPEN/CLOSE shutter opened
Card remote commander
RM-X151
RM-X151
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
A
Volume +/– button
To adjust volume.
B
ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
again.
C
DSPL (display) button 4, 8, 10
To change display items.
D
SEL (select) button 4, 9, 10, 12
To select items.
E
Display window
F
EQ3 (equalizer) button 2, 9
To select an equalizer type (XPLOD,
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
CDX-R5610
DSPL
SEEK
ATT
OFF
SEL
DSO
OPEN/CLOSE
EQ3
SOURCE
MODE
LIST
SENS
BBE MP
SHUF
REP
GP/DISC +
-
BTM
6
5
4
3
2
1
1 2
3 4
6
7 8
9
qk
qj
qh
qg
qf
qd
qs
qa
0
5
ql
DSPL
SEEK
ATT
OFF
SEL
DSO
OPEN/CLOSE
EQ3
PTY
SENS
LIST
BTM
BBE MP
SHUF
REP
GP/DISC
+
-
AF/TA
6
5
4
3
2
1
SOURCE
MODE
w;
wa
OFF
DSPL
SCRL
SEL
SOURCE
MODE
1
3
2
4
6
5
ATT
VOL
+
–
+
–
2
3
8
qa
qs
4
wg
ws
wd
wh
wf
7
G
DSO button 2
To select the DSO mode (1, 2, 3 or OFF).
The larger the number, the more enhanced
the effect.
The larger the number, the more enhanced
the effect.
H
OFF button
To power off/stop the source.
I
SEEK +/– button
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
J
(front panel release) button 4
K
SOURCE button
To power on/change the source (Radio/CD/
MD*
MD*
1
).
L
MODE button 8, 11
To select the radio band (FM/AM)/select the
unit*
unit*
2
.
M
RESET button
(located behind the front
panel)
4
N
Number buttons
Radio:
To receive stored stations (press); store
stations (press and hold).
CD/MD*
To receive stored stations (press); store
stations (press and hold).
CD/MD*
1
:
(1)/(2):
GP
*
3
/
DISC
*
2
–/+
To skip groups (press); skip groups
continuously (press and hold).
(3):
continuously (press and hold).
(3):
REP 8
(4):
SHUF 8
(5):
BBE MP 2
To activate the BBE MP function, to set
“BBEMP-ON” during playback on this unit.
To cancel, set “BBEMP-OFF.”
“BBEMP-ON” during playback on this unit.
To cancel, set “BBEMP-OFF.”
O
Frequency select switch
(
located on
the bottom of the unit
)
See “Frequency Select switch” in the
supplied installation/connections manual.
supplied installation/connections manual.
P
BTM button 8
To start the BTM function.
Q
SENS button
To improve weak reception: LOCAL/
MONO.
MONO.
R
LIST button 10
To list up.
S
Receptor for the card remote
commander
commander
T
Disc slot
5
U Z
(eject) button 6
The following buttons on the card remote
commander have also different buttons/functions
from the unit.
commander have also different buttons/functions
from the unit.
ws <
(
.
)/
,
(
>
) buttons
To control radio/CD, the same as (SEEK)
+/– on the unit. (For details of other
operations, see “With the card remote
commander” on each pages.)
+/– on the unit. (For details of other
operations, see “With the card remote
commander” on each pages.)
wd
VOL +/– button
To adjust volume.
wf M
(+)/
m
(–) buttons
To control CD, the same as (1)/(2) –/+ on
the unit. (For details of other operations, see
“With the card remote commander” on each
pages.)
the unit. (For details of other operations, see
“With the card remote commander” on each
pages.)
wg
SCRL (scroll) button 8
To scroll the display item.
wh
Number buttons
To receive stored stations (press); store
stations (press and hold).
stations (press and hold).
*1
When an MD changer is connected.
*2
When a CD/MD changer is connected.
*3
When an MP3/ATRAC CD is played and a changer
i
i
s not connected. If the changer is connected, the
operation is different, see page 11.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless
(SOURCE)
on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 14.
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 14.
• CDX-R5610
6
CDX-R5515X/R5610/R6550
• CONNECTIONS
• CDX-R5515X
6
Location of controls and basic operations
Main unit
OPEN/CLOSE shutter opened
Card remote commander
RM-X151
RM-X151
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
A
Volume +/– button
To adjust volume.
B
ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
again.
C
DSPL (display) button 4, 8, 12
To change display items.
D
SEL (select) button 4, 11, 12
To select items.
E
Display window
F
EQ3 (equalizer) button 2, 11
To select an equalizer type (XPLOD,
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
CDX-R6550
DSPL
SEEK
ATT
OFF
SEL
DSO
OPEN/CLOSE
EQ3
SOURCE
MODE
PTY
SENS
LIST
BTM
BBE MP
SHUF
REP
GP/DISC +
-
AF/TA
6
5
4
3
2
1
1 2
3 4
6
7 8
9
qj
qh
qg
qf
qd
qs
qa
0
5
qk
DSPL
SEEK
ATT
OFF
SEL
DSO
OPEN/CLOSE
EQ3
PTY
SENS
LIST
BTM
BBE MP
SHUF
REP
GP/DISC
+
-
AF/TA
6
5
4
3
2
1
SOURCE
MODE
ql
w;
OFF
DSPL
SCRL
SEL
SOURCE
MODE
1
3
2
4
6
5
ATT
VOL
+
–
+
–
2
3
8
qa
qs
4
wf
wa
ws
wg
wd
7
G
DSO button 2
To select the DSO mode (1, 2, 3 or OFF).
The larger the number, the more enhanced
the effect.
The larger the number, the more enhanced
the effect.
H
OFF button
To power off/stop the source.
I
SEEK +/– button
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
J
(front panel release) button 4
K
SOURCE button
To power on/change the source (Radio/CD/
MD*
MD*
1
).
L
MODE button 8, 12
To select the radio band (FM/MW/LW)/
select the unit*
select the unit*
2
.
M
RESET button
(located behind the front
panel)
4
N
Number buttons
Radio:
To receive stored stations (press); store
stations (press and hold).
CD/MD*
To receive stored stations (press); store
stations (press and hold).
CD/MD*
1
:
(1)/(2):
GP
*
3
/
DISC
*
2
–/+
To skip groups (press); skip groups
continuously (press and hold).
(3):
continuously (press and hold).
(3):
REP 8
(4):
SHUF 8
(5):
BBE MP 2
To activate the BBE MP function, to set
“BBEMP-ON” during playback on this unit.
To cancel, set “BBEMP-OFF.”
“BBEMP-ON” during playback on this unit.
To cancel, set “BBEMP-OFF.”
O
AF (Alternative Frequencies)/TA
(Traffic Announcement) button 9
(Traffic Announcement) button 9
To set AF and TA/TP in RDS.
P
SENS/BTM button 8
To improve weak reception: LOCAL/MONO
(press); start the BTM function (press and
hold).
(press); start the BTM function (press and
hold).
Q
PTY (Programme Type)/LIST button
10
10
To select PTY in RDS; list up.
R
Receptor for the card remote
commander
commander
S
Disc slot
5
T Z
(eject) button
5
The following buttons on the card remote
commander have also different buttons/functions
from the unit.
commander have also different buttons/functions
from the unit.
wa <
(
.
)/
,
(
>
) buttons
To control radio/CD, the same as (SEEK)
+/– on the unit. (For details of other
operations, see “With the card remote
commander” on each pages.)
+/– on the unit. (For details of other
operations, see “With the card remote
commander” on each pages.)
ws
VOL +/– button
To adjust volume.
wd M
(+)/
m
(–) buttons
To control CD, the same as (1)/(2) –/+ on
the unit. (For details of other operations, see
“With the card remote commander” on each
pages.)
the unit. (For details of other operations, see
“With the card remote commander” on each
pages.)
wf
SCRL button 8
To scroll the display item.
wg
Number buttons
To receive stored stations (press); store
stations (press and hold).
stations (press and hold).
*1
When an MD changer is connected.
*2
When a CD/MD changer is connected.
*3
When an MP3/ATRAC CD is played and a changer
is not connected. If the changer is connected, the
operation is different, see page 12.
is not connected. If the changer is connected, the
operation is different, see page 12.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless
(SOURCE)
on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 15.
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 15.
• CDX-R6550
Connection example (2)
Notes (
2
-A)
• Be sure to connect the ground lead before connecting the
amplifi er.
• The alarm will only sound if the built-in amplifi er is used.
Tip (
2
-B- )
For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.
selector XA-C30 (optional) is necessary.
A
B
AUDIO OUT FRONT
AUDIO OUT REAR
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN
Source selector
*
Sélecteur de source
*
XA-C30
*
not supplied
non fourni
Exemple de raccordement (2)
Remarques (
2
-A)
• Raccordez d’abord le câble de mise à la masse avant de
raccorder l’amplifi cateur.
• L’alarme est émise uniquement lorsque l’amplifi cateur intégré
est utilisé.
Conseil (
2
-B- )
Dans le cas du raccordement de deux changeurs de CD/MD ou
plus, le sélecteur de source XA-C30 (en option) est requis.
plus, le sélecteur de source XA-C30 (en option) est requis.
7
CDX-R5515X/R5610/R6550
• CDX-R5610
• CDX-R6550
Connection example (2)
Notes
(
2
-A)
• Be sure to connect the earth lead before connecting the
amplifi er.
• The alarm will only sound if the built-in amplifi er is used.
Tip
(
2
-B- )
For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.
selector XA-C30 (optional) is necessary.
AUDIO OUT FRONT
AUDIO OUT REAR
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN
A
B
*
not supplied
nicht mitgeliefert
non fourni
non in dotazione
niet bijgeleverd
non in dotazione
niet bijgeleverd
Source selector
*
Signalquellenwähler
*
Sélecteur de source
*
Selettore di fonte
*
Geluidsbronkiezer
*
XA-C30
Anschlussbeispiel (2)
Hinweise
(
2
-A)
• Schließen Sie unbedingt zuerst das Massekabel an, bevor Sie
den Verstärker anschließen.
• Der Warnton wird nur ausgegeben, wenn der integrierte
Verstärker verwendet wird.
Tipp
(
2
-B- )
Zum Anschließen von zwei oder mehr CD/MD-Wechslern wird
der gesondert erhältliche Signalquellenwähler XA-C30 benötigt.
der gesondert erhältliche Signalquellenwähler XA-C30 benötigt.
Exemple de raccordement (2)
Remarques
(
2
-A)
• Raccordez d’abord le câble de mise à la masse avant de
connecter l’amplifi cateur.
• L’alarme est émise uniquement lorsque l’amplifi cateur intégré
est utilisé.
Conseil
(
2
-B- )
Dans le cas du raccordement de deux changeurs de CD/MD
ou plus, le sélecteur de source XA-C30 (en option) est
indispensable.
ou plus, le sélecteur de source XA-C30 (en option) est
indispensable.
Esempio di collegamento (2)
Note
(
2
-A)
• Assicurarsi di collegare il cavo di terra prima di collegare
l’apparecchio all’amplifi catore.
• Tale segnale viene emesso solo se è in uso l’amplifi catore
incorporato.
Suggerimento
(
2
-B- )
Per collegare due o più cambia CD/MD, si deve utilizzare il
selettore di fonte XA-C30 (opzionale).
selettore di fonte XA-C30 (opzionale).
Voorbeeldaansluitingen (2)
Opmerkingen
(
2
-A)
• Sluit eerst de aarddraad aan voordat u de versterker aansluit.
• U hoort de pieptoon alleen als de ingebouwde versterker wordt
• U hoort de pieptoon alleen als de ingebouwde versterker wordt
gebruikt.
Tip
(
2
-B- )
Om twee of meer CD/MD-wisselaars aan te sluiten, hebt u de
geluidsbronkiezer XA-C30 (optioneel) nodig.
geluidsbronkiezer XA-C30 (optioneel) nodig.
8
CDX-R5515X/R5610/R6550
• CDX-R5515X
L
R
BUS AUDIO IN
AUDIO OUT
FRONT
AUDIO OUT
REAR
*
2
BUS
CONTROL IN
REMOTE
IN
2
4
5
6
7
1
3
AMP REM
Max. supply current 0.3 A
Courant max. fourni 0,3 A
Courant max. fourni 0,3 A
Fuse (10 A)
Fusible (10 A)
Fusible (10 A)
Blue/white striped
Rayé bleu/blanc
Rayé bleu/blanc
ANT REM
2
*
1
Red
Rouge
Rouge
Yellow
Jaune
Jaune
Black
Noir
Noir
Blue
Bleu
Bleu
White
Blanc
Blanc
Green
Vert
Vert
Purple
Mauve
Mauve
White/black striped
Rayé blanc/noir
Rayé blanc/noir
Gray/black striped
Rayé gris/noir
Rayé gris/noir
Green/black striped
Rayé vert/noir
Rayé vert/noir
Gray
Gris
Gris
Left
Gauche
Gauche
Right
Droit
Droit
Left
Gauche
Gauche
Right
Droit
Droit
*
1
RCA pin cord (not supplied)
*
2
AUDIO OUT can be switched SUB or
REAR. For details, see the Operating
Instructions manual.
REAR. For details, see the Operating
Instructions manual.
*
3
Insert with the cord upwards.
*
1
Cordon à broche RCA (non fourni)
*
2
AUDIO OUT peut être commuté sur SUB
ou REAR. Pour obtenir plus de détails,
reportez-vous au mode d’emploi.
ou REAR. Pour obtenir plus de détails,
reportez-vous au mode d’emploi.
*
3
Insérez avec le câble vers le haut.
Purple/black striped
Rayé mauve/noir
Rayé mauve/noir
Remarques sur les câbles de commande et d’alimentation
• Le câble de commande d’antenne électrique (bleu) fournit une
• Le câble de commande d’antenne électrique (bleu) fournit une
alimentation de + 12 V CC lorsque vous mettez la radio sous
tension.
tension.
• Lorsque votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, raccordez le câble de
commande d’antenne (bleu) ou l’entrée d’alimentation des
accessoires (rouge) à la borne d’alimentation de l’amplifi cateur
d’antenne existant. Pour plus de détails, consultez votre
détaillant.
commande d’antenne (bleu) ou l’entrée d’alimentation des
accessoires (rouge) à la borne d’alimentation de l’amplifi cateur
d’antenne existant. Pour plus de détails, consultez votre
détaillant.
• Une antenne électrique sans boîtier de relais ne peut pas être
utilisée avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le câble d’entrée d’alimentation jaune est raccordé, le
circuit de la mémoire est alimenté en permanence même si la clé
de contact est sur la position d’arrêt.
Lorsque le câble d’entrée d’alimentation jaune est raccordé, le
circuit de la mémoire est alimenté en permanence même si la clé
de contact est sur la position d’arrêt.
Remarques sur le raccordement des haut-parleurs
• Avant de raccorder les haut-parleurs, mettez l’appareil hors
• Avant de raccorder les haut-parleurs, mettez l’appareil hors
tension.
• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms
avec une capacité électrique adéquate pour éviter de les
endommager.
endommager.
• Ne raccordez pas les bornes du système de haut-parleurs au
châssis de la voiture et ne raccordez pas les bornes des haut-
parleurs droit à celles du haut-parleur gauche.
parleurs droit à celles du haut-parleur gauche.
• Ne raccordez pas le câble de mise à la masse de cet appareil
à la borne négative (–) du haut-parleur.
• N’essayez pas de raccorder les haut-parleurs en parallèle.
• Raccordez uniquement des haut-parleurs passifs. Le
• Raccordez uniquement des haut-parleurs passifs. Le
raccordement de haut-parleurs actifs (avec amplifi cateurs
intégrés) aux bornes des haut-parleurs peut endommager
l’appareil.
intégrés) aux bornes des haut-parleurs peut endommager
l’appareil.
• Pour éviter tout problème de fonctionnement, n’utilisez pas les
câbles des haut-parleurs intégrés installés dans votre voiture si
l’appareil partage un câble négatif commun (–) pour les haut-
parleurs droit et gauche.
l’appareil partage un câble négatif commun (–) pour les haut-
parleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-parleurs de
l’appareil.
Remarque sur le raccordement
Si les haut-parleurs et l’amplifi cateur ne sont pas raccordés
correctement, le message « FAILURE » s’affi che. Dans ce cas,
assurez-vous que les haut-parleurs et l’amplifi cateur sont bien
raccordés.
Si les haut-parleurs et l’amplifi cateur ne sont pas raccordés
correctement, le message « FAILURE » s’affi che. Dans ce cas,
assurez-vous que les haut-parleurs et l’amplifi cateur sont bien
raccordés.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V DC
• The power antenna control lead (blue) supplies +12 V DC
when you turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/side
glass, connect the power antenna control lead (blue) or the
accessory power input lead (red) to the power terminal of the
existing antenna booster. For details, consult your dealer.
accessory power input lead (red) to the power terminal of the
existing antenna booster. For details, consult your dealer.
• A power antenna without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
left speaker.
• Do not connect the ground lead of this unit to the negative (–)
terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
• Connect only passive speakers. Connecting active speakers
(with built-in amplifi ers) to the speaker terminals may damage
the unit.
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifi er are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
If speaker and amplifi er are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
*
1
Source selector
(not supplied)
Sélecteur de source
(non fourni)
XA-C30
Supplied with the CD/MD changer
Fourni avec le changeur de CD/MD
Fourni avec le changeur de CD/MD
*
3
Max. supply current 0.1 A
Courant max. fourni 0,1 A
Courant max. fourni 0,1 A
ILLUMINATION
Light blue
Bleu ciel
Bleu ciel
Orange/white striped
Rayé orange/blanc
Rayé orange/blanc
ATT
from car antenna
à partir de l’antenne de la voiture
Supplied with XA-C30
Fourni avec le XA-C30
Fourni avec le XA-C30
Schéma de raccordement (3)
1
À un point métallique de la voiture
Branchez d’abord le fi l de masse noir et, ensuite, les fi ls
d’entrée d’alimentation rayé orange/blanc, jaune, et rouge.
d’entrée d’alimentation rayé orange/blanc, jaune, et rouge.
2
Vers le câble de commande d’antenne
électrique ou le câble d’alimentation de
l’amplifi cateur d’antenne
l’amplifi cateur d’antenne
Remarques
• Il n’est pas nécessaire de raccorder ce câble s’il n'y a pas
• Il n’est pas nécessaire de raccorder ce câble s’il n'y a pas
d’antenne électrique ni d’amplifi cateur d’antenne, ou avec
une antenne télescopique manuelle.
une antenne télescopique manuelle.
• Si votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, voir « Remarques
sur les câbles de commande et d’alimentation ».
sur les câbles de commande et d’alimentation ».
3
Au niveau de AMP REMOTE IN de
l’amplifi cateur de puissance en option
Ce raccordement s’applique uniquement aux amplifi cateurs.
Le branchement de tout autre système risque
d’endommager l’appareil.
Le branchement de tout autre système risque
d’endommager l’appareil.
4
Vers le cordon de liaison d’un téléphone de
voiture
5
Vers le connecteur du signal d’éclairage de
la voiture
Raccordez d’abord le fi l de masse noir à un point métallique
du véhicule.
du véhicule.
6
À la borne +12 V qui est alimentée quand la
clé de contact est sur la position accessoires
Remarques
• S’il n’y a pas de position accessoires, raccordez la borne
• S’il n’y a pas de position accessoires, raccordez la borne
d’alimentation (batterie) +12 V qui est alimentée en
permanence. Raccordez d’abord le câble de mise à la
masse noir à un point métallique du véhicule.
permanence. Raccordez d’abord le câble de mise à la
masse noir à un point métallique du véhicule.
• Si votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, voir « Remarques
sur les câbles de commande et d’alimentation ».
sur les câbles de commande et d’alimentation ».
7
À la borne +12 V qui est alimentée en
permanence
Raccordez d’abord le câble de mise à la masse noir à un
point métallique du véhicule.
point métallique du véhicule.
Connection diagram (3)
1
To a metal surface of the car
First connect the black ground lead, then connect the
orange/white striped, yellow, and red power input leads.
orange/white striped, yellow, and red power input leads.
2
To the power antenna control lead or power
supply lead of antenna booster amplifi er
Notes
• It is not necessary to connect this lead if there is no power
• It is not necessary to connect this lead if there is no power
antenna or antenna booster, or with a manually-operated
telescopic antenna.
telescopic antenna.
• When your car has a built-in FM/AM antenna in the rear/
side glass, see “Notes on the control and power supply
leads.”
leads.”
3
To AMP REMOTE IN of an optional power
amplifi er
This connection is only for amplifi ers. Connecting any other
system may damage the unit.
system may damage the unit.
4
To the interface cable of a car telephone
5
To a car’s illumination signal
Be sure to connect the black ground lead to a metal surface
of the car fi rst.
of the car fi rst.
6
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground lead to a metal
surface of the car fi rst.
• When your car has a built-in FM/AM antenna in the rear/
side glass, see “Notes on the control and power supply
leads.”
leads.”
7
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground lead to a metal surface
of the car fi rst.
of the car fi rst.
Click on the first or last page to see other CDX-R5515X / CDX-R5610 / CDX-R6550 service manuals if exist.