Sony CDX-GS500R Service Manual ▷ View online
CDX-GS500R
9
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
3-2. MINI FUSE (BLADE TYPE) (10A/32V) (FU1),
COVER
(Page
COVER
(Page
10)
3-3. SUB PANEL BLOCK
(Page
(Page
10)
3-4. CD MECHANISM DECK (MG-101CA-188)
(Page
(Page
11)
3-6. MAIN
BOARD
(Page
12)
SET
FRONT PANEL SECTION
Note: Illustration of disassembly is omitted.
Note: Illustration of disassembly is omitted.
3-7. SERVO
BOARD
(Page
12)
3-8. CHASSIS (T) SUB ASSY
(Page
(Page
13)
3-9. ROLLER ARM ASSY
(Page
(Page
13)
3-10. CHASSIS (OP) ASSY
(Page
(Page
14)
3-12. SLED MOTOR ASSY
(Page
(Page
15)
3-13. OPTICAL PICK-UP SECTION
(Page
(Page
16)
3-14. OPTICAL PICK-UP
(Page
(Page
16)
3-11. CHUCKING ARM SUB ASSY
(Page
(Page
14)
3-5. CONNECTION CABLE (AUTOMOBILE) ( )
(CNC1)
(Page
(CNC1)
(Page
11)
CDX-GS500R
10
3-3. SUB PANEL BLOCK
Note: Follow the disassembly procedure in the numerical order given.
3-2. MINI FUSE (BLADE TYPE) (10A/32V) (FU1), COVER
2 two bosses
3 three claws
2 two bosses
4 cover
1 mini fuse (blade type) (10A/32V)
(FU1)
2 two claws
2 two claws
3 sub panel block
1 two screws
(PTT2.6
u 6)
CDX-GS500R
11
3-4. CD MECHANISM DECK (MG-101CA-188)
3 connector
(CN700)
1 screw
(PTT2.6
u 6)
1 screw
(PTT2.6
u 6)
2 Lift up the CD mechanism block.
6 CD mechanism deck
(MG-101CA-188)
4 two screws
(PTT2.6
u 4)
5 bracket (CD)
3-5. CONNECTION CABLE (AUTOMOBILE) (
) (CNC1)
3 screw
(PTT2.6
u 8)
2 connector (CN1300)
lead pin
CN1300
:LUHVHWWLQJ
1 Remove the wire from lead pin.
4 connection cable (automobile) ( )
(CNC1)
CDX-GS500R
12
3-6. MAIN BOARD
3-7. SERVO BOARD
6 SERVO board
3 claw
4 claw
SERVO board
2 toothed lock screw
(M1.7
u 2.5)
2 toothed lock screw
(M1.7
u 2.5)
1 Remove the eleven solders.
GRY
YEL
BLU
ORG
RED
BLK
RED
WHT
BLK
RED
WHT
5 optical pick-up (16 core)
(CN101)
CD mechanism deck
–
CD mechanism deck bottom side view
–
Note: When the complete MAIN board is replaced, the destination
setting is necessary. Refer to “NOTE THE MAIN BOARD OR
SYSTEM CONTROLLER (IC501) REPLACING” on page 4.
SYSTEM CONTROLLER (IC501) REPLACING” on page 4.
1 three ground point screws
(PTT2.6
u 6)
2 screw
(PTT2.6
u 8)
2 screw
(PTT2.6
u 8)
3 MAIN board
Click on the first or last page to see other CDX-GS500R service manuals if exist.