Sony CDX-828 Service Manual ▷ View online
– 49 –
7-14.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC201 CXP84332-208Q (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Function
1 to 3
—
O
Not used (open)
4
CH.F
O
Motor drive signal (load chucking direction) output to the chucking motor drive (IC52)
“L” active *1
“L” active *1
5
CH.R
O
Motor drive signal (save direction) output to the chucking motor drive (IC52)
“L” active *1
“L” active *1
6
LOAD2
I
Chucking end detect switch (SW11) input terminal
“L”: When completion of the disc chucking operation
“L”: When completion of the disc chucking operation
7
LOAD1
I
Save end detect switch (SW12) input terminal
“L”: When completion of the disc chucking operation
“L”: When completion of the disc chucking operation
8
SENS2
I
Internal status signal (sense signal) input from the CXA1992BR (IC11)
9
LIM.SW
I
Sled limit in detect switch (SW1) input terminal
“L”: When the optical pick-up is inner position
“L”: When the optical pick-up is inner position
10
EE.INIT
I
Initialize signal input for the EEPROM (IC202) “H”: format Fixed at “L” in this set
11
EE.CLK
O
Serial data transfer clock signal output to the EEPROM (IC202)
12
EE.DATA
I/O
Two-way data bus with the EEPROM (IC202)
13 to 19
—
O
Not used (open)
20
SINGLE
I
Setting terminal for the single disc/multiple discs mode
“L”: single mode, “H”: multiple discs mode (fixed at “H”)
“L”: single mode, “H”: multiple discs mode (fixed at “H”)
21
XRST
O
System reset signal output to the CXA1992BR (IC11), CXD2530Q (IC101) and CXD2522Q
(IC401) “L”: reset
(IC401) “L”: reset
22
FOK
I
Focus OK signal input from the CXA1992BR (IC11) “L”: NG, “H”: OK
23
SENS
I
Internal status signal (sense signal) input from the CXD2530Q (IC101)
24
GFS
I
Guard frame sync signal input from the CXD2530Q (IC101) “L”: NG, “H”: OK
25
GRSRT
O
Reset signal output to the CXD2522Q (IC401) “L”: reset
26
XQOK
O
Subcode Q OK pulse signal output to the CXD2522Q (IC401) “L” active
27
SDTI
I
ESP status signal input from the CXD2522Q (IC401)
28
XSOE
O
ESP status read enable signal output to the CXD2522Q (IC401) “L” active
29
ESPXLT
O
ESP latch pulse signal output to the CXD2522Q (IC401) “L” active
30
RST
I
System reset signal input from the SONY bus interface (IC302) and reset signal generator (IC304)
“L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
“L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
31
EXTAL
I
Main system clock input terminal (8 MHz)
32
XTAL
O
Main system clock output terminal (8 MHz)
33
VSS
—
Ground terminal
34
TX
O
Sub system clock output terminal Not used (open)
35
TEX
I
Sub system clock input terminal Not used (fixed at “L”)
36
AVSS
—
Ground terminal (for A/D converter)
37
AVREF
I
Reference voltage (+5V) input terminal (for A/D converter)
38
MCK
I
Input of signal for the fine adjustment (linear position sensor adjustment; RV201) of elevator
position (A/D input)
position (A/D input)
39
EHS
I
Elevator height position detect input from the RV202 (elevator height sensor) (A/D input)
40
H.TEMP
I
High temperature sensor input terminal Not used (fixed at “L”)
41
XRDE
O
D-RAM read enable signal output to the CXD2522Q (IC401) “L” active
42
XWRE
O
D-RAM write enable signal output to the CXD2522Q (IC401) “L” active
43
A.MUTE
O
Audio line muting on/off control signal output terminal “H”: muting on
44
EMP
O
Emphasis mode output to the D/A converter (IC601) “H”: emphasis on
45
ML
O
Fast speed dubbing control signal output to the D/A converter (IC601) “L”: fast speed
46
GRSCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2522Q (IC401)
– 50 –
Pin No.
Pin Name
I/O
Function
47
D/A.RESET
O
Reset signal output to the D/A converter (IC601) “L”: reset
48
SCK
I
Serial data transfer clock signal input from the SONY bus interface (IC302)
49
SI
I
Serial data input from the SONY bus interface (IC302)
50
SO
O
Serial data output to the SONY bus interface (IC302)
51
SCLK
O
Subcode Q data reading clock signal output to the CXD2530Q (IC101)
52
SUBQ
I
Subcode Q data input from the CXD2530Q (IC101)
53
—
O
Not used (open)
54
C.OUT
I
Track number count signal input from the CXA1992BR (IC11)
55
BUS.ON
I
Bus on/off control signal input from the SONY bus interface (IC302) “H”: bus on
56
A/D.SW
I
Analog/digital select switch (SW801) input terminal “L”: digital, “H”: analog
57
MGLK
I
Magazine eject operation completion detect switch (SW201) input “L”: eject completed
58
ELV.F
O
Motor drive signal (elevator up direction) output to the elevator motor drive (IC301)
“L” active *2
“L” active *2
59
—
O
Not used (open)
60
MAG.SW
I
Magazine in/out detect switch (SW202) input “L”: magazine detected
61
BU.CHK
I
Battery detection signal input terminal “H”: battery on
62
W.UP
I
Bus on or eject switch (SW301) input terminal “H”: bus on or eject switch pushing
63
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2530Q (IC101)
64
EJECT
I
Eject switch (SW301) input terminal “H” active
65
CD.CLK
O
Serial data transfer clock signal output to the CXD2530Q (IC101) and CXD2522Q (IC401)
66
CD.XLT
O
Serial data latch pulse signal output to the CXD2530Q (IC101)
67
CD.DATA
O
Serial data output to the CXD2530Q (IC101) and CXD2522Q (IC401)
68
CD.ON
O
D/A converter and servo section power supply on/off control signal output “H”: power on
69
ELV.ON
O
Mechanism deck section power supply on/off control signal output “H”: power on
70
ELV.R
O
Motor drive signal (elevator down direction) output to the elevator motor drive (IC301)
“L” active *2
“L” active *2
71
—
O
Not used (open)
72
VDD
—
Power supply terminal (+5V)
73
NC (VDD)
—
Connected to the power supply (+5V)
74
BUSY
I
Busy monitor input from the CD text decoder (IC501) “L”: busy status
75
RESET
O
Reset signal output to the CD text decoder (IC501) “L”: reset
76
REQ
I
Data request signal input from the CD text decoder (IC501) “L” active
77
CCCLK
O
Command clock signal output to the CD text decoder (IC501)
78
CSO
O
Command data output to the CD text decoder (IC501)
79
CSI
I
Command data input from the CD text decoder (IC501)
80
ADJ
I
Automatic/manual adjustment selection terminal
“L”: manual adjustment mode, “H”: automatic adjustment mode (fixed at “H” in this set)
“L”: manual adjustment mode, “H”: automatic adjustment mode (fixed at “H” in this set)
*1 chucking motor (M103) control
STOP
LOAD
CHUCKING
SAVE
BRAKE
CH.F (pin 4)
“H”
“L”
“H”
“L”
CH.R (pin 5)
“H”
“H”
“L”
“L”
Mode
Terminal
*2 elevator motor (M104) control
STOP
ELEVATOR
UP
ELEVATOR
DOWN
BRAKE
ELV.F (pin %•)
“H”
“L”
“H”
“L”
ELV.R (pin &º)
“H”
“H”
“L”
“L”
Mode
Terminal
– 51 –
•
MAIN BOARD IC501 CXP83413-049Q (CD TEXT DECODER)
Pin No.
Pin Name
I/O
Function
1, 2
NC
O
Not used (open)
3
NC
I
Not used (fixed at “L”)
4
REQ
O
Request signal output to the system controller (IC201) “L” active
5
CCLK
I
Serial data transfer clock signal input from the system controller (IC201)
6
CSI
I
Serial data input from the system controller (IC201)
7
CSO
O
Serial data output to the system controller (IC201)
8
SCLK
O
Clock signal output for subcode data reading to the CXD2530Q (IC101)
9
SSI
I
Subcode data input from the CXD2530Q (IC101)
10
NC
O
Not used (open)
11 to 18
ADD0 to ADD7
O
Address signal output to the S-RAM (IC502)
19
NC
I
Not used (fixed at “L”)
20 to 27
DATA0 to DATA7
I/O
Two-way data bus with the S-RAM (IC502)
28
RST
I
System reset signal input from the system controller (IC201), SONY bus interface (IC302) and
reset signal generator (IC304) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
reset signal generator (IC304) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
29
EXTAL
I
System clock input terminal (10 MHz)
30
XTAL
O
System clock output terminal (10 MHz)
31
VSS
—
Ground terminal
32 to 55
NC
O
Not used (open)
56
BUSY
O
Busy signal output to the system controller (IC201) “L”: busy status
57 to 61
NC
O
Not used (open)
62
CE
O
Chip enable signal output to the S-RAM (IC502) “L” active
63
WE
O
Data write enable signal output to the S-RAM (IC502) “L” active
64 to 69
ADD8 to ADD13
O
Address signal output to the S-RAM (IC502)
70
VDD
—
Power supply terminal (+5V)
71, 72
NC
O
Not used (open)
73
NC
I
Not used (fixed at “H”)
74
ADD14
O
Address signal output to the S-RAM (IC502)
75
NC
O
Not used (open)
76
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2530Q (IC101)
77
WFCK
I
Write frame clock (7.35 kHz) signal input from the CXD2530Q (IC101)
78
BUCK
I
Backup power supply detection signal input terminal (used also to reset standby)
79, 80
NC
I
Not used (fixed at “L”)
– 52 –
(1)
COVER SECTION
SECTION 8
EXPLODED VIEWS
Les composants identifiés par une
marque
marque
! sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Ne les remplacer que par une pièce
portant le numéro spécifié.
The components identified by
mark
mark
! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
specified.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
3-010-104-01 DAMPER (250)
* 2
3-010-097-11 COVER (LOWER)
3
1-664-796-11 JACK FLEXIBLE BOARD
* 4
1-672-617-11 JACK BOARD
5
X-3376-459-1 DOOR (T) ASSY (EXCEPT US, Canadian)
5
X-3376-831-1 DOOR ASSY (US, Canadian)
6
3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT
7
3-030-489-11 PANEL, FRONT
8
3-012-388-01 SCREW (M2X3)
* 9
3-010-105-01 ESCUTCHEON (US, Canadian)
* 9
3-022-006-01 ESCUTCHEON (T) (EXCEPT US, Canadian)
* 10
3-010-106-01 BUTTON (EJ) (
6) (US, Canadian)
* 10
3-022-007-01 BUTTON (EJT) (
6) (EXCEPT US, Canadian)
* 11
3-022-012-01 HEAT SINK (T)
12
3-010-103-01 SPRING (FL), TENSION
13
3-010-101-01 LEVER (FL)
* 14
3-010-096-11 COVER (UPPER)
* 15
A-3317-605-A MAIN BOARD, COMPLETE
* 16
3-022-694-01 HOLDER (TR3)
17
3-935-636-11 SCREW (FP)
18
X-3373-215-1 ARM (FL) ASSY (US, Canadian)
18
X-3375-357-1 ARM (FLT) ASSY (EXCEPT US, Canadian)
* 19
3-013-658-01 SHEET (FJ), PROTECTION
20
X-3373-986-1 ARM (FR) ASSY (US, Canadian)
20
X-3375-360-1 ARM (FRT) ASSY (EXCEPT US, Canadian)
* 21
3-024-065-01 CUSHION (EJECT) (EXCEPT US, Canadian)
21
3-350-124-01 CUSHION (EJECT) (US, Canadian)
22
3-028-802-01 SPACER (MOUNT 30)
* 23
1-672-618-11 DIGITAL OUT BOARD
* 24
3-011-205-01 BRACKET (LIGHT)
25
3-011-204-01 COVER (LIGHT) (US, Canadian)
25
3-011-204-11 COVER (LIGHT) (EXCEPT US, Canadian)
26
3-924-924-01 COVER (LIGHT) (US, Canadian)
26
3-924-924-11 COVER (LIGHT) (EXCEPT US, Canadian)
27
3-912-956-11 SCREW (2.6X6) (CU), +BVTT
28
3-024-067-01 CUSHION (T), BATTERY
(EXCEPT US, Canadian)
28
3-911-215-02 SHEET (LEAD RETAINER) (US, Canadian)
IC303
8-759-054-12 IC PQ09RA1
IC305
8-759-231-53 IC TA7805S
5
7
13
14
27
13
12
15
16
22
8
10
9
11
12
6
4
3
19
1
26
25
24
21
19
2
1
20
28
18
17
#2
#2
#11
#2
#2
#1
not supplied
#13
MG-250C-137
main flexible board
IC303
IC305
23
Click on the first or last page to see other CDX-828 service manuals if exist.