Sony CDX-757MX Service Manual ▷ View online
17
CDX-757MX
SECTION 4
MECHANICAL ADJUSTMENT
• Elevator Height (Address) Adjustment
Note:
This adjustments is necessary when the system controller (IC201),
variable resistor (RV201), slider (R), slider (L), or chassis (ELV)
was replaced for any repair.
variable resistor (RV201), slider (R), slider (L), or chassis (ELV)
was replaced for any repair.
Connection:
Adjustment Method:
1. Connect this set to the master unit (e.g. MDX-C7970), load a
1. Connect this set to the master unit (e.g. MDX-C7970), load a
disc magazine, and place the set vertically as shown below.
2. Connect the regulated power supply to the master unit, and
turn the power on.
3. Press the DISC button on the master unit and select DISC 5.
4. At this time, if the elevator shaft does not position between
4. At this time, if the elevator shaft does not position between
comb teeth A and B at addresses 5 and 6 as shown below,
adjust the following.
adjust the following.
5. Press repeatedly the DISC + and – buttons on the master unit
so that the elevator shafts moves from address 6 to address 5,
or from 5 to 6. At this time, adjust RV201 on the main board
so that the elevator shaft positions smoothly between comb
teeth A and B.
or from 5 to 6. At this time, adjust RV201 on the main board
so that the elevator shaft positions smoothly between comb
teeth A and B.
6. Further, place the set horizontally and make same adjustment
as mentioned above.
7. After adjustment at addresses 5 to 6 is finished, check all op-
erations from addresses 1 to 10 with the set placed vertically
and horizontally respectively to confirm that the elevator shaft
positions in a range between comb teeth A to B.
and horizontally respectively to confirm that the elevator shaft
positions in a range between comb teeth A to B.
GND
+
BUS cable
compact disc changer
master unit
CONTROL connector
(CN901)
(CN901)
power supply
(DC 14.4 V)
RV201
comb tooth at address 6
elevator shaft
comb tooth at address 6
comb tooth at address 5
OK
NG
elevator shaft
comb tooth at address 5
A
B
A
B
18
CDX-757MX
SECTION 5
ELECTRICAL CHECK
Note:
1. This check is performed with the set placed horizontally.
2. Power supply voltage: DC14.4 V (more than 3 A).
3. Be sure to use the disc “YEDS-18” parts code: 3-702-101-01, but only
2. Power supply voltage: DC14.4 V (more than 3 A).
3. Be sure to use the disc “YEDS-18” parts code: 3-702-101-01, but only
when indicated.
4. Use a master unit that supports SONY bus system.
Connection:
FOCUS BIAS CHECK
Connection:
– RF Board (Component Side) –
Procedure:
1. Connect the oscilloscope to TP (RFAC) and TP (VC) on the
1. Connect the oscilloscope to TP (RFAC) and TP (VC) on the
RF board.
2. Put the set into play mode by loading the disc (YEDS-18).
3. Confirm that oscilloscope waveform is clear and check RF sig-
3. Confirm that oscilloscope waveform is clear and check RF sig-
nal level is correct or not.
Note:
Clear RF signal waveform means that the shape “
◊” can be clearly distin-
guished at the center of the waveform.
When observing the eye pattern, set the oscilloscope to AC range
and raise the vertical sensitivity so that it may be easily seen.
and raise the vertical sensitivity so that it may be easily seen.
GND
+
BUS cable
compact disc changer
master unit
CONTROL connector
(CN901)
(CN901)
power supply
(DC 14.4 V)
RF signal waveform
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
(10 : 1 probe in use)
TIME/DIV: 500 ns
(10 : 1 probe in use)
level: 1.4
±
0.3 Vp-p
oscilloscope
(AC range)
+
–
–
TP (VC)
TP (RFAC)
IC101
CDX-757MX
19
19
TRACKING OFFSET CHECK
Connection:
– RF Board (Component Side) –
Procedure:
1. Connect the oscilloscope to TP (TE) and TP (VC) on the RF
1. Connect the oscilloscope to TP (TE) and TP (VC) on the RF
board.
2. Put the set into play mode by loading the disc (YEDS-18).
3. Press the
3. Press the
[ AMS ]
button on the master unit, and check
the traverse waveform*.
4. Confirm that the oscilloscope waveform is symmetrical on the
top and bottom in relation to 0 V dc, and check this level.
* Traverse waveform: This is the tracking error wave form appears
when crossing the track.
A
B
0 V
A=B
traverse waveform
(100 track jump waveform)
(100 track jump waveform)
VOLT/DIV: 500 mV
TIME/DIV: 2 ms
Center: 0 V
TIME/DIV: 2 ms
Center: 0 V
Traverse waveform
oscilloscope
(DC range)
+
–
–
TP (VC)
TP (TE)
IC101
. >
CDX-757MX
20
20
6-1.
BLOCK DIAGRAM – SERVO Section –
SECTION 6
DIAGRAMS
RFAC
SUMMING
AMP
RFDC
SUMMING
AMP
AC
SUM
4
3
EQ IN
7
8
9
A
B
C
D
RW/ROM
28
30
16
18
RFDCO
DC OFST
FE
TE
E
F
10
11
FOCUS
ERROR
AMP
TRACKING
ERROR
AMP
SW
PD
12
2
LD
1
APC AMP
RW/ROM
15
RFAC
RFAC
VCA
RF EQ
AMP
116, 115,
118, 117
RF
FE
TE
109 – 106, 7 – 5,
3 – 1, 111
9 – 12, 15 – 19,
21, 8
2, 3,
24, 25
5
23
4
22
RAS
CAS
WE
OE
113
119
114
120
XRAS
XCAS
XWE
XOE
VIBRATION
MEMORY
CONTROLLER
&
COMPRESSION
EXPANDER
A0 – A10
A0 – A10
DQ1 – DQ4
D0 – D3
RFAC
ASYI
ASYO
71
73
74
66 69 68 67
FILO
CLTV
PCO
FILI
ASYMMETRY
CORRECTOR
DIGITAL
PLL
EFM
DEMODULATOR
INTERNAL BUS
D/A
INTERFACE
ERROR
CORRECTOR
32k RAM
15
15
15
90
88
86
BCK
PCMD
LRCK
SELECTOR
DIGITAL
OUT
15
85
DOUT
15
93
15
94
XTAI
XTAO
CLOCK
GENERATOR
15
78
15
81
WDCK
GFS
15
23
15
25
15
24
15
26
15
14
15
15
15
17
DATA
CLOK
XLAT
SENS
SQSO
SQCK
SCOR
SUBCODE
PROCESSOR
CPU
INTERFACE
XRDE
XWRE
XQOK
15
9
15
8
15
12
XRDE
XWRE
XQOK
SERVO AUTO
SEQUENSOR
SCLK
FOK
XRST
27
35
21
SERVO
INTERFACE
45
SSTP
TE
FE
RF
SE
TE
FE
RFDC
61
60
62
58
OP AMP
ANALOG SW
A/D CONVERTER
SERVO DSP
PWM GENERATOR
50
51
48
49
46
47
43
FFDR
FRDR
TFDR
TRDR
SFDR
SRDR
MDP
MIRR
DECT
FOK
DIGITAL
CLV
6
7
8
9
10
11
12
13
5
4
VO4 +
VO4 –
VO3 +
VO3 –
VO2 +
VO2 –
VO1 +
VO1 –
VL0 +
VL0 –
VIN4 +
VIN4 –
VIN3 +
VIN3 –
VIN2 +
VIN2 –
FWD
REV
31
32
25
24
22
21
1
2
MOTOR
DRIVE
MOTOR
DRIVE
MOTOR
DRIVE
COIL
DRIVE
MOTOR
DRIVE
COIL
DRIVE
TRACKING/FOCUS COIL DRIVE,
SLED/SPINDLE/CHUCKING
MOTOR DRIVE
IC201
A
B
C
D
E
F
I-V AMP
PD
LD
DETECTOR
(TRACKING)
(FOCUS)
2-AXIS DEVICE
OPTICAL
PICK-UP BLOCK
(KSS-720A)
LASER DIODE
M
M
M101
(SLED)
M
M
M102
(SPINDLE)
M
M
M103
(CHUHCKING)
15
88
SW3
(LIMIT)
SW1
(CHUCKING END DETECT)
SW2
(SAVE END DETECT)
ON : When the optical pick-up
is inner position
is inner position
ON : When completion of the disc
save operation
save operation
ON : When completion of the disc
chucking operation
chucking operation
ON : When the optical pick-up
is inner position
is inner position
ON : When completion of the disc
save operation
save operation
ON : When completion of the disc
chucking operation
chucking operation
R/RW SEL
GRSCOR
GFS
CDDAT
CDCLK
CDLAT
SENS
SCOR
XRDE
XWRE
XQOK
SCLK
LIM SW
LOAD SW
SAVE SW
XRST
FOK
SQSO
SQCK
90
40
5
10
8
9
7
38
16
17
15
6
98
11
4
84
85
LOADF
LOADR
95
96
99
CD-ROM/RW
SELECT SWITCH
Q202
RF AMP OFFSET
CONTROL SWITCH
Q102
SIGNAL PATH
: CD PLAY
FILTER
DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO PROCESSOR,
D-RAM CONTROLLER
IC101
D-RAM
IC102
AUTOMATIC
POWER
CONTROL
Q101
RF AMP,
FOCUS/TRACKING ERROR AMP
IC101
6
SYSTEM CONTROLLER
IC201 (1/3)
VIN1-B
18
VC
27
DVC 14
VC
CE
VC
59
63
15
89
PCMDI
DAC
X101
16.9344MHz
A
B
C
BCK
SDI
LRCK
XTAL-IN
SDO
100
D201
D
TCXRDE
(Page 21)
(Page 21)
(Page 21)
(Page 21)
Click on the first or last page to see other CDX-757MX service manuals if exist.