DOWNLOAD Sony CDX-616 Service Manual ↓ Size: 2.25 MB | Pages: 44 in PDF or view online for FREE

– 45 –

Pin No.

Pin Name

I/O

Function

47

D/A.RESET

O

Reset signal output terminal    “L”: reset    Not used (open)

48

SCK

I

Serial data transfer clock signal input from the SONY bus interface (IC302)

49

SI

I

Serial data input from the SONY bus interface (IC302)

50

SO

O

Serial data output to the SONY bus interface (IC302)

51

SCLK

O

Subcode Q data reading clock signal output to the CXD2530Q (IC101)

52

SUBQ

I

Subcode Q data input from the CXD2530Q (IC101)

53

—

O

Not used (open)

54

C.OUT

I

Track number count signal input from the CXA1992BR (IC11)

55

BUS.ON

I

Bus on/off control signal input from the SONY bus interface (IC302)    “H”: bus on

56

NC

I

Not used (fixed at “L”)

57

MGLK

I

Magazine eject operation completion detect switch (SW201) input    “L”: eject completed

58

ELV.F

O

Motor drive signal (elevator up direction) output to the elevator motor drive (IC301)
“L” active    *2

59

—

O

Not used (open)

60

MAG.SW

I

Magazine in/out detect switch (SW202) input    “L”: magazine detected

61

BU.CHK

I

Battery detection signal input terminal    “H”: battery on

62

W.UP

I

Bus on or eject switch (SW301) input terminal    “H”: bus on or eject switch pushing

63

SCOR

I

Subcode sync (S0+S1) detection signal input from the CXD2530Q (IC101)

64

EJECT

I

Eject switch (SW301) input terminal    “H” active

65

CD.CLK

O

Serial data transfer clock signal output to the CXD2530Q (IC101)

66

CD.XLT

O

Serial data latch pulse signal output to the CXD2530Q (IC101)

67

CD.DATA

O

Serial data output to the CXD2530Q (IC101)

68

CD.ON

O

D/A converter and servo section power supply on/off control signal output    “H”: power on

69

ELV.ON

O

Mechanism deck section power supply on/off control signal output    “H”: power on

70

ELV.R

O

Motor drive signal (elevator down direction) output to the elevator motor drive (IC301)
“L” active    *2

71

—

O

Not used (open)

72

VDD

—

Power supply terminal (+5V)

73

NC (VDD)

—

Connected to the power supply (+5V)

74

BUSY

I

Busy monitor input from the CD text decoder (IC501)    “L”: busy status

75

RESET

O

Reset signal output to the CD text decoder (IC501)    “L”: reset

76

REQ

I

Data request signal input from the CD text decoder (IC501)    “L” active

77

CCCLK

O

Command clock signal output to the CD text decoder (IC501)

78

CSO

O

Command data output to the CD text decoder (IC501)

79

CSI

I

Command data input from the CD text decoder (IC501)

80

—

I

Not used (open)

*1  chucking motor (M103) control

STOP

LOAD

CHUCKING

SAVE

BRAKE

CH.F (pin 4)

“H”

“L”

“H”

“L”

CH.R (pin 5)

“H”

“H”

“L”

“L”

Mode

Terminal

*2  elevator motor (M104) control

STOP

ELEVATOR 

UP

ELEVATOR

DOWN

BRAKE

ELV.F (pin %•)

“H”

“L”

“H”

“L”

ELV.R (pin &º)

“H”

“H”

“L”

“L”

Mode

Terminal

– 46 –

•

Pin No.

Pin Name

I/O

Function

1, 2

NC

O

Not used (open)

3

NC

I

Not used (fixed at “L”)

4

REQ

O

Request signal output to the system controller (IC201)    “L” active

5

CCLK

I

Serial data transfer clock signal input from the system controller (IC201)

6

CSI

I

Serial data input from the system controller (IC201)

7

CSO

O

Serial data output to the system controller (IC201)

8

SCLK

O

Clock signal output for subcode data reading to the CXD2530Q (IC101)

9

SSI

I

Subcode data input from the CXD2530Q (IC101)

10

NC

O

Not used (open)

11 to 18

ADD0 to ADD7

O

Address signal output to the S-RAM (IC502)

19

NC

I

Not used (fixed at “L”)

20 to 27

DATA0 to DATA7

I/O

Two-way data bus with the S-RAM (IC502)

28

RST

I

System reset signal input from the system controller (IC201), SONY bus interface (IC302) and 
reset signal generator (IC304)    “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”

29

EXTAL

I

System clock input terminal (10 MHz)

30

XTAL

O

System clock output terminal (10 MHz)

31

VSS

—

Ground terminal

32 to 55

NC

O

Not used (open)

56

BUSY

O

Busy signal output to the system controller (IC201)    “L”: busy status

57 to 61

NC

O

Not used (open)

62

CE

O

Chip enable signal output to the S-RAM (IC502)    “L” active

63

WE

O

Data write enable signal output to the S-RAM (IC502)    “L” active

64 to 69

ADD8 to ADD13

O

Address signal output to the S-RAM (IC502)

70

VDD

—

Power supply terminal (+5V)

71

NC

O

Not used (open)

72

NC

I

Not used (fixed at “L”)

73

NC

I

Not used (fixed at “H”)

74

ADD14

O

Address signal output to the S-RAM (IC502)

75

NC

O

Not used (open)

76

SCOR

I

Subcode sync (S0+S1) detection signal input from the CXD2530Q (IC101)

77

WFCK

I

Write frame clock (7.35 kHz) signal input from the CXD2530Q (IC101)

78

BUCK

I

Backup power supply detection signal input terminal (used also to reset standby)

79, 80

NC

I

Not used (fixed at “L”)

– 47 –

The components identified by
mark 

! or dotted line with mark

! are critical for safety.

Replace only with part number
specified.

• Items marked “*” are not stocked since they

are seldom required for routine service. Some
delay should be anticipated when ordering
these items.

• The mechanical parts with no reference num-

ber in the exploded views are not supplied.

• Hardware (# mark) list and accessories and

packing materials are given in the last of the
electrical parts list.

NOTE:

• -XX and -X mean standardized parts, so they

may have some difference from the original
one.

• Color Indication of Appearance Parts

Example:
KNOB, BALANCE (WHITE) . . . (RED)

↑

↑

Parts Color Cabinet's Color

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

1

3-010-104-01 DAMPER (250)

* 2

3-010-097-01 COVER (LOWER T)

3

1-664-628-11 JACK FLEXIBLE BOARD

* 4

1-673-252-11 JACK BOARD

5

X-3376-772-1 DOOR (616T) ASSY

6

3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT

7

3-022-002-52 PANEL (T), FRONT

8

3-012-388-01 SCREW (M2X3)

9

3-022-006-01 ESCUTCHEON (T)

10

3-022-007-01 BUTTON (EJT) (

6)

* 11

3-022-012-01 HEAT SINK (T)

12

3-010-103-01 SPRING (FL), TENSION

13

3-010-101-01 LEVER (FLT)

* 14

3-010-096-01 COVER (UPPER T)

* 15

A-3317-431-A MAIN BOARD, COMPLETE

* 16

3-032-997-01 HOLDER (TR4)

17

3-935-636-11 SCREW (FP)

18

X-3375-357-1 ARM (FLT) ASSY

* 19

3-013-658-01 SHEET (FJT), PROTECTION

20

X-3375-360-1 ARM (FRT) ASSY

* 21

3-024-065-01 CUSHION (EJECT)

22

3-024-067-01 CUSHION (T), BATTERY

23

3-028-802-01 SPACER (MOUNT 30)

Q307

8-729-019-00 TRANSISTOR   2SD2394-G

Q309

8-729-019-00 TRANSISTOR   2SD2394-G

#2

#2

#2

#3

#2

#2

#1

not supplied

main flexible board

MG-250C-137

Q307

Q309

– 48 –

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

51

X-3375-497-1 CHASSIS (U) SUB ASSY

52

3-024-161-01 SPRING (SUT)

#3

#3

#3

53

4-965-759-01 WASHER, POLYETHYLENE

54

3-011-997-01 SPRING (STOPPER. LOWER)