DOWNLOAD Sony CDX-565MXRF Service Manual ↓ Size: 2.76 MB | Pages: 54 in PDF or view online for FREE

17

8

two precision screws
(P1.7 

×

 2.2)

7

3

spring (chucking)

6

retainer (disc)

4

precision screw
(P2 

×

 2.2)

5

bracket (CP)

9

Remove the spindle motor (S) sub assy (M102) 
in the direction of the arrow.

2

LSW board

1

precision screw
(P2 

×

 2.5)

2

two screws 
(PTT2 

×

 4)

3

retainer (CHM)

4

ELJ motor 
assy
(chucking) 
(M103)

1

Remove two solders of 
the chucking motor leads (M103).

18

• This set can be assembled in the order shown below.

3-2. OPTICAL PICK-UP COMPLETE ASSY

(Page 18)

3-3. GEAR (LOMINI) / (LOAD 1) ASSY

(Page 19)

3-4. OPERATION CHECK

(Page 19)

chuck plate

1

Move the lever (LOCK 3A) in the direction of arrow 

A

, 

and return it a little in the direction of arrow 

B

 

from the position where the chuck plate is moved
down to the lower limit.

A

B

3

stop ring 2.0 (E type)

4

tension spring (DH)

2

optical pick-up complete assy
Note: Insert the shaft (A) first.

shaft (A)

19

1

Confirm that the slider moves in the direction of arrow 

C

 to move down

the chuck plate if the gear (LOAD 1) is rotated in the direction of arrow 

A

or the chuck plate moves up and the slider moves in the direction of arrow

D

 if the gear is rotated in the direction of arrow 

B

.

gear (LOAD 2)

gear (LOMINI)

marking
Fig. A

chuck plate

2

Attach the gear (LOMINI) at the position 
shown in Fig. A.

shaft (rotary prevention C)

1

Move the lever (LOCK 3A)
fully in the direction of arrow 

B

 

to move the chuck plate up.

B

4

stop ring 1.5 (E type)

3

Attach the gear (LOAD 1) assy
with its facing inside.

slit

chuck plate

slider

gear (LOAD 1) assy

A

B

C

D

20

This adjustments is necessary when the system controller (IC201),
variable resistor (RV201), slider (R), slider (L), or chassis (ELV)
was replaced for any repair.

Perform following the adjustment by the wired remote commander
(RM-X83RF).

1. Load a disc magazine, and place the set vertically as shown

below.

2. Connect the regulated power supply, and turn the power on.
3. Select DISC 5.
4. At this time, if the elevator shaft does not position between

comb teeth A and B at addresses 5 and 6 as shown below,
adjust the following.

5. Select DISC 5 and DISC 6 alternately, so that the elevator shafts

moves from address 6 to address 5, or from 5 to 6. At this
time, adjust RV201 on the main board so that the elevator shaft
positions smoothly between comb teeth A and B.

6. Further, place the set horizontally and make same adjustment

as mentioned above.

7. After adjustment at addresses 5 to 6 is finished, check all op-

erations from addresses 1 to 10 with the set placed vertically
and horizontally respectively to confirm that the elevator shaft
positions in a range between comb teeth A to B.

power supply

(DC 14.4 V)

compact disc changer

wired remote commander

(RM-X83RF)

GND

+

DISPLAY connector (CN302)

POWER connector (CN303)