DOWNLOAD Sony CDX-4483ESP Service Manual ↓ Size: 1.24 MB | Pages: 51 in PDF or view online for FREE

– 17 –

• When installing, take note of the positions
  arm (roller) and washers. (Fig. 1)

2

 PS 2x5

3

 PS 2x5

!¡

 PS 2x5

4

 heat sink

1

 PTT 2.6x5

0

 CN4

6

 P 2x3

7

 loading motor assy

!™

 SERVO board

5

 wires

8

 CN2

9

 CN5

4

 PS 2x4

5

 LOAD SW board

1

 tension spring (RA)

2

 arm (roller)

3

 roller assy

washer arm

arm

washer

washers

– 18 –

1

 tension spring (angle)

8

 compression spring (FL)

6

 chassis (OP) (O/S) assy

7

 compression spring (FL)

4

 Fit lever (D) in the

     direction of the arrow.

3

 damper (T)

2

 damper (T)

5

 Turn loading ring in the

     direction of the arrow.

1

 P 2x3

2

 sled motor assy

3

 optical pick-up block

– 19 –

Carrier frequency : 98.00 MHz
Output level

: 22 dB (12.6 

µ

V)

Mode

: mono

Modulation

: 1 kHz, 22.5 kHz deviation (30%)

Procedure :
1. Set to the test mode.
2. Push the  SOURCE  button and set to FM.

Display

D-BASS switch : OFF
SOURCE button : FM

3. Push the preset  3  button.

Display

CD section adjustments are done automatically in this set.

µ

When the tuner unit is defective, replace it by a new one
because its internal block is difficult to repair.

This set have the test mode function. In the test mode, FM Auto
Scan/Stop Level and MW Auto Scan/Stop Level adjustments can
be performed easier than it in ordinary procedure.

<Set the Test Mode>
1. Set the “OFF” mode.
2. Push the preset  4  button.
3. Push the preset  5  button.
4. Press the preset  1  button for more than two seconds.
5. Then the display indicates all lights, the test mode is set.

<Release the Test Mode>
1. Push the  OFF  button.

The adjustments of tuner section, should be performed according
to the following sequence.
1. FM Auto Scan/Stop Level Adjustment
2. FM Stereo Separation Adjustment
3. FM Polar VCO Adjustment
4. FM Polar Pilot Adjustment
5. MW Auto Scan/Stop Level Adjustment

4. Adjust with the volume RV2 on TU1 so that the “FM” indication

turns to “FM0” indication on the display window.
But, in case of already indicated “FM0”, turn the RV2 so that
put out light “0” indication and adjustment.

Display

FM RF signal

generator

0.01 

µ

F

antenna
terminal

set

Adjustment Location : See page 22.

– 20 –

+

–

FM RF signal

generator

0.01 

µ

F

antenna
terminal

set

LINE OUT REAR

10 k 

Ω

level meter

D-BASS switch : OFF
SOURCE button : FM

Carrier frequency : 98.00 MHz
Output level

: 70 dB (3.2 mV)

Mode

: stereo

Modulation

: main : 1 kHz, 20 kHz deviation (26.5%)

sub : 1 kHz, 20 kHz deviation (26.5%)
19 kHz pilot : 7.5 kHz deviation (10%)

L-CH

L-CH

A

B

R-CH

L-CH

Adjust RV4 on TU1 for
minimum reading.

R-CH

R-CH

C

D

L-CH

R-CH

Adjust RV4 on TU1 for
minimum reading.

L-CH stereo separation : A – B
R-CH stereo separation : C – D
The separations of both channels should be equal.

Specification : Separation more than 28 dB

Adjustment Location : See page 22.

Carrier frequency : 69.5 MHz (FM2 : 3CH)
Output level

: 60 dB (1 mV)

Procedure :
1. Connect the frequency counter to the TP2 on main board.
2. Adjust RV601 so that the reading on the frequency counter

becomes to 31.25 

±

 0.1 kHz.

Adjustment Location : See page 22.

D-BASS switch : OFF
SOURCE button : FM

FM RF signal

generator

antenna
terminal

set

+

–

frequency
counter

main board

TP2