Sony CCD-CR1 / CCD-CR1E (serv.man2) Service Manual ▷ View online
2-2
2-2. VC-205 BOARD
3
2
4
4
1
Control switch block
CN601 15P (VC-205 board)
2
CD-191 board
CN501 30P (VC-205 board)
To assemble it, insert
the claw of the shield
case into the cut-out
of the plate spring.
the claw of the shield
case into the cut-out
of the plate spring.
6
FP-685 flexible board
CN801 20P (VC-205 board)
CD-191
BO
BO
ARD
VC-205
BO
BO
ARD
3
Remove the
two claws
5
VC-205 board
Cut out of plate spring
Claw of shield
2-3
2-3. CABINET (UPPER), LENS UNIT, CD-191 BOARD
3
Tapping screw (M1.7
×
4)
2
4
Cabinet (upper)
To assemble, align
the head of the control
shaft with the groove
of the ZOOM knob.
the head of the control
shaft with the groove
of the ZOOM knob.
1
Disengage
the claw.
1
—
2
Cabinet (upper)
3
,
4
Lens unit
5
,
6
CD-191 board
7
,
8
Iris assy
Lens unit
To assemble, align the pin of the
control pulley with the groove of
the ZOOM disk of the lens unit.
control pulley with the groove of
the ZOOM disk of the lens unit.
ZOOM disk
Control pulley
3
Tapping screw (M1.7
×
4)
9
Screws, lock ace
(M1.7
×
1.6)
8
Iris assy
7
Screw (P1.7
×
3.5)
5
Tapping screws
(B1.7
×
6)
6
CD-191 board
!º
Tapping screws
(M1.7
×
3)
!¡
Base plate
C
D
-19
1
Bo
ard
2-4
2-4. BATTERY CASE (BATTERY CASE, BATTERY LID ASSEMBLY)
1
Remove the BT flexible
cover to the direction of arrow.
2
BT case shaft
3
Battery case terminal
Move while it is
warped and swayed.
warped and swayed.
2-5. PD-99 BOARD, LCD PANEL ASSEMBLY
!™
Screw, lock ace
(M1.7
×
1.4)
!£
Open the hinge to one side.
8
Remove
the spring.
6
While peeling off the sheet,
remove the speaker.
2
FP-686 flexible
board CN701
1
Peel off the
insulation sheet.
3
Speaker connector
4
Screw (M1.4
×
2.5)
!º
Tapping screws
(M1.7
×
3)
4
Screw
(M1.4
×
2.5)
1
—
5
PD-99 board
6
,
7
Speaker
8
—
!∞
Hinge
1
—
8
Hinge disassembling
and re-assembling
7
Be careful not to
tighten up excessively.
1
Route the flexible board
coming from the LCD through.
Assembling the hinge
!¡
!¢
!∞
9
7
5
!™
Screws,
lock ace
(M1.7
(M1.7
×
1.4)
2
3
4
5
6
8
PD-99
BO
BO
ARD
2-5
2-6. LCD PANEL
2-7. MJ-88 BOARD, MIC
3
6
Screws (M1.4
×
2)
1
—
5
MJ-88 board
6
,
7
MIC
1
MIC cable
CN753 2P
2
Screw (M1.4
×
2)
4
Screws
(M1.4
×
2)
MIC1
MJ-88 board
7
5
Microphone retainer
3
LCD panel
1
Screws (M1.4
×
2)
1
Screws (M1.4
×
2)
2
2
Be carefull not to
rotate over 180˚
rotate over 180˚
4
Spacer panel
Click on the first or last page to see other CCD-CR1 / CCD-CR1E (serv.man2) service manuals if exist.