Sony ZS-R100CP Service Manual ▷ View online
ZS-R100CP
13
2-13. USB BOARD
5
USB board
2
ferrite core
(FC1)
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When you install the flexible flat cable, please install themcorrectly.
There is a possibility that this machine damageswhen not correctly
installing
it.
USB board
loudspeaker (8 cm) (L-CH) (SP101)
USB board
tape
ferrite core
30 ± 5 mm
:LUHVHWWLQJ
:LUHVHWWLQJ
USB board
Bend twice.
tape
:LUHVHWWLQJ
–5HDUVLGHYLHZ–
–3DQHOIURQWEORFNUHDUVLGHYLHZ–
3
flexible flat cable
(9 core) (CN610)
1
screw
(PWH tapping B2.6)
4
three screws
(BV tapping B2.6)
4
three screws
(BV tapping B2.6)
Twist the wire around the
ferrite core two times, and
fix it by a tape.
ferrite core two times, and
fix it by a tape.
ZS-R100CP
14
2-14. LOUDSPEAKER (8 cm) (SP101, SP201)
3
loudspeaker wire
4
loudspeaker (8 cm)
(L-CH)
(SP101)
loudspeaker (8 cm) (L-CH) (SP101)
loudspeaker (8 cm) (L-CH) (SP101)
loudspeaker (8 cm)
(L-CH) (SP101)
(L-CH) (SP101)
4
loudspeaker (8 cm)
(R-CH)
(SP201)
loudspeaker (8 cm) (R-CH) (SP201)
2
Remove two
solders.
2
Remove two
solders.
loudspeaker (8 cm)
(R-CH) (SP201)
(R-CH) (SP201)
USB board
red (+)
red (+)
black (-)
white (+)
white (+)
black (-)
black (-)
black (-)
:LUHVHWWLQJ
:LUHVHWWLQJ
:LUHVHWWLQJ
–5HDUVLGHYLHZ–
1
screw
(BV tapping B2.6)
1
screw
(BV tapping B2.6)
1
three screws
(BV tapping B2.6)
1
three screws
(BV tapping B2.6)
–3DQHOIURQWEORFNUHDUVLGHYLHZ–
ZS-R100CP
15
2-15. LCD BOARD BLOCK
2-16. WIRE SETTING
– chassis (net) block rear side view –
2
LCD board block
1
five screws
1
six screws
tape
tape
tape
tape
front side
tape
– Front side view –
Bend twice.
ZS-R100CP
16
SECTION 3
TEST MODE
COLD RESET
The contents of the EEPROM are initialized, and it can return to
the setup at the time of shipment.
The contents of the EEPROM are initialized, and it can return to
the setup at the time of shipment.
Note 1: Don’t enter the mode in other test modes.
Note 2: Only LCD contrast automatic adjustment doesn’t initialize, but
Note 2: Only LCD contrast automatic adjustment doesn’t initialize, but
LCD contrast automatic adjustment values are copied to LCD
contrast values, and write-in processing is performed.
contrast values, and write-in processing is performed.
Procedure:
1. Press three buttons of [OPERATE], [MODE] and [
1. Press three buttons of [OPERATE], [MODE] and [
.
] simul-
taneously.
2. The microprocessor is reset, and it is displayed as shown in the
following fi gure, then becomes the standby state.
R E S E T
PANEL TEST
It can perform all segments on the liquid crystal display light-up,
fi rmware version display and destination display.
It can perform all segments on the liquid crystal display light-up,
fi rmware version display and destination display.
Note 1: Don’t enter the mode in other test modes.
Note 2: Don’t enter the mode in other test modes while being entering the
Note 2: Don’t enter the mode in other test modes while being entering the
mode.
Procedure:
1. In the standby state, press the [OPERATE] button to turn the
1. In the standby state, press the [OPERATE] button to turn the
power on.
2. Press three buttons of [SLEEP], [MODE] and [
.
] simulta-
neously.
3. It enters the panel test mode, all segments on the liquid crystal
display light up as shown in the following fi gure.
4. When pressing the [RADIO FM/AM] button, it changes ver-
sion and destination display as shown in the following fi gure.
(When pressing the [RADIO FM/AM] button again, it return
to all segments on the liquid crystal display light-up)
to all segments on the liquid crystal display light-up)
0 8 0 9 U 0 0 7
1 0 3 1 C E
0 9 0 2 V 0 1 4
V E R
ROM presentation date and version of system
microprocessor are displayed on the second line
in the screen.
(Display example of above figure is September 2, Ver. 014)
ROM presentation date and version of USB microprocessor
are displayed on the third line in the screen.
(Display example of above figure is October 9, Ver. 007)
Model code (1031) and destination (CE) are displayed on
the forth line in the screen.
Releasing method:
Press three buttons of [SLEEP], [MODE] and [
Press three buttons of [SLEEP], [MODE] and [
.
] simultane-
ously.
CD SERVICE MODE
It can perform sled movement and laser power supply on/off.
It can perform sled movement and laser power supply on/off.
Note 1: Don’t enter the mode in other test modes.
Note 2: Don’t enter the mode in other test modes while being entering the
Note 2: Don’t enter the mode in other test modes while being entering the
mode.
Procedure:
1. In the standby state, press the [OPERATE] button to turn the
1. In the standby state, press the [OPERATE] button to turn the
power on.
2. Press the [CD] button to turn the CD function.
3. Set the CD disc to this unit.
4. Press three buttons of [CD], [MODE] and [
3. Set the CD disc to this unit.
4. Press three buttons of [CD], [MODE] and [
>
] simultane-
ously.
5. It enters the CD service mode, it is displayed as shown in the
following fi gure.
Track 12
C D
SERVICE
6. Sled moves to inner circumference while being pressing the
[
.
] button, and it is displayed as shown in the following
fi gure.
SL IN
C D
SERVICE
7. Sled moves to outer circumference while being pressing the
[
>
] button, and it is displayed as shown in the following
fi gure.
SL O
C D
SERVICE
8. Each time the [MODE] button is pressed, laser power supply
on/off of the optical pick-up changes, and it is displayed as
shown in the following fi gure.
shown in the following fi gure.
(The display sample is case that turned the laser power supply
on)
on)
LD ON
C D
SERVICE
Releasing method:
Press three buttons of [CD], [MODE] and [
Press three buttons of [CD], [MODE] and [
>
] simultaneously.
Click on the first or last page to see other ZS-R100CP service manuals if exist.