Sony ZS-PE40CP (serv.man2) Service Manual ▷ View online
ZS-PE40CP
9
2-6. FERRITE CORE (FC1)
– Rear top view –
OK
NG
CD board
CD board
:ire VettiQJ
POWER board
Wire from the inlet AC (2P) (J981) is upper.
Wire from the ferrite core (FC1) is under.
1 connector (CN501)
2 tape
(sub
material)
3 connector
(CN703)
8 ferrite core (FC1)
ferrite core (FC1)
ferrite core (FC1)
tape
(sub material)
(sub material)
Be based on
a black line.
a black line.
Roll the wire three times.
to USB board
to CD board
6 tape
(sub
material)
7 wire
4 tapping screw
(PWH
B2.6)
:ire VettiQJ
5 Remove the ferrite core block
in the direction of an arrow.
:ire VettiQJ
:ire VettiQJ
tape
(sub material)
(sub material)
POWER board
POWER board
ZS-PE40CP
10
2-7. CD BOARD
4 Solder the short-land.
Note 3: When assembling the CD
board block, remove the
solder of short-land after
connecting the flexible flat
cable (16 core).
3 Remove the CD board block
in the direction of an arrow.
5 flexible flat cable
(16 core) (CN701)
7 flexible flat cable (26 core) (FFC5)
(CN702)
flexible flat cable (26 core) (FFC5)
2 three tapping screws
(BV
B2.6)
8 CD board
tape
(sub material)
(sub material)
CD board
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note 4: When installing the flexible flat cable, ensure the colored line.
No slanting after insertion.
Note 1: Before disconnecting the fl exible fl at cable (16 core) of optical pick-up block, solder the short-land.
Note 2: Do not touch the
terminal
terminal
wire.
terminal wire
6 tape
(sub
material)
1 connector
(CN730)
– Rear top view –
:LUHVHWWLQJ
ZS-PE40CP
11
2-8. CD BLOCK ASSY
A
B
4 CD block assy
– Rear top view –
3 two tapping screws
(PWH
B2.6)
3 two tapping screws
(PWH
B2.6)
1 tape
(sub
material)
2 spring
(CD
mecha)
CD block assy
CD block assy
CD block assy
OK
NG
:ire VettiQJ
:ire VettiQJ
6priQJ &' PeFKa VettiQJ
tape
(sub material)
(sub material)
Wire passes through
the top of the screw.
the top of the screw.
Note: When installing the spring (CD mecha),
install
install
on the order of
A, B.
ZS-PE40CP
12
2-9. OPTICAL PICK-UP (DA11B3VFGP) (OP1)
2-10. DISPLAY BOARD
3 claw
3 claw
6 optical pick-up (DA11B3VFGP)
(OP1)
optical pick-up
(DA11B3VFGP)
(OP1)
(DA11B3VFGP)
(OP1)
4 CD cover
Note: Four claws might be fixed by bond.
When installing the CD cover, please
fix four claws using the following bond.
Part No.
Description
7-432-912-48 SONY BOND SC608LV (180 ml)
5 vibration proof rubber
5 vibration proof rubber
5 vibration proof rubber
5 vibration proof rubber
vibration proof rubber
Front side
Rear side
9LEUDWLRQSURRIUXEEHUVHWWLQJ
3 claw
3 claw
2 connector
1 flexible flat cable
(16 core) (FFC6)
5 tapping screw
(BV
B2.6)
5 tapping screw
(BV
B2.6)
4 flexible flat cable (6 core) (FFC1)
(CN605)
flexible flat
cable (18 core)
cable (18 core)
Press two flexible flat cables
flexible flat
cable (22P)
cable (22P)
DISPLAY board
3 flexible flat cable (4P) (FFC2)
(CN604)
1 flexible flat cable (22P)
(CN601)
6 DISPLAY board
2 flexible flat cable
(18
core)
(CN602)
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
:LUHVHWWLQJ
Note: When installing the flexible
flat cable, ensure the colored
line.
No slanting after insertion.
Click on the first or last page to see other ZS-PE40CP (serv.man2) service manuals if exist.