Sony XDR-S60DBP Service Manual ▷ View online
XDR-S60DBP
5
2-5. CABINET (REAR) BLOCK
4 tapping screw
(BV
B2.6)
4 two tapping screws
(BV
B2.6)
2 tapping screw
(P
B2.6)
4 four tapping screws
(BV
B2.6)
1 battery case lid block
A
7 cabinet (rear) block
3 lid (connector)
6 connector
(CN402)
5
Remove the cabinet rear block
in the direction of an arrow.
–
Rear view
–
Note 1: When installing the cabinet
(rear) block, arrange wire in
the direction of the arrow
A.
The wire cannot be seen.
The wire can be seen.
OK
NG
–
Rear view
–
–
Rear view
–
Note 2: When installing the cabinet (rear) block, arrange wire in
check that the wire is not visible from the hole for the connector.
–
Cabinet (rear) block front bottom view
–
Wire setting
2 tape
(sub
material)
tape (sub material)
3 Remove the solder.
[red]
7 Remove the solder.
[red]
5 JACK HOLD board
8 Remove the bond.
9 wire fuse
(F102)
wire fuse (F102)
JACK board
1 Remove the solder.
[black]
6 Remove the JACK board block
in the direction of an arrow.
Note: When installing the wire fuse (F102), the guidance
of fuse must not be hidden by a tape (sub material).
4 tapping screw
(PWH
B2.6)
The wire [black] is upper.
The wire [blue/white/red] is under.
2-6. WIRE FUSE (F102)
XDR-S60DBP
6
2-7. CHASSIS BLOCK
:LUHVHWWLQJ
:LUHVHWWLQJ
:LUHVHWWLQJ
–
5HDUERWWRPYLHZ
–
–
/HIWYLHZ
–
0 Remove the chassis block in
the direction of an arrow.
9 Move the flexible flat cable
(13 core) in the direction of
an
arrow.
6 connector
(CN406)
3 connector
(CN503)
AMP board
< Fig. A >
4 flexible flat cable (13 core)
(CN407)
flexible flat cable (13 core)
MAIN board
5 claw
8 screw
(P2.6
u 6)
8 screw
(P2.6
u 6)
7 Remove the solder.
[gray] (See Fig. A)
RV401
J401
J402
2 Remove the solder.
[white] (See Fig. A)
2 Remove the solder.
[red] (See Fig. A)
[white]
[gray]
[red]
MAIN board
screw hole boss
MAIN board hole
AMP board
1 Remove the speaker wire
from the claw.
Note 2: When installing the chassis block,
confirm that J401, J402 and RV401
are installed securely.
Note 3: When installing the chassis
block,
block,
confirm that screw
hole boss is installed securely
to MAIN board hole.
qa chassis block
Note
1: When installing the chassis block,
be careful not to pinch wires.
XDR-S60DBP
7
2-8. AMP BOARD
8 AMP board
:LUHVHWWLQJ
–
&KDVVLVEORFNUHDUWRSYLHZ
–
2 Remove the solder.
[red]
1 Remove the solder.
[black]
6 claw
7 rib
2 Remove the solder.
[white]
from
W206
W206
[red]
[white]
[blue]
[black]
2 Remove the solder.
[blue]
3 Remove the solder.
[blue]
3 Remove the solder.
[white]
3 Remove the solder.
[red]
4 screw
(P2.6
u 6)
5 Remove the AMP board
in the direction of an arrow.
from
W207
W207
[red]
[white]
[blue]
XDR-S60DBP
8
2-10. MODULE ASSY (DAB MODULE) (DAB1)
2-9. MAIN BOARD BLOCK
4 MAIN board block
chassis
plate (antenna)
Cut this part.
Note: When the chassis replacing,
cut off the part as shown in the
figure
below.
2 two screws
(P2.6
u 6)
3 two claws
3 claw
2 screw
(P2.6
u 6)
2 screw
(P2.6
u 6)
1 Remove the solder.
[white]
–
Chassis block rear top view
–
3 Remove eighteen solders.
1 Remove the solder.
1 Remove the solder.
1 Remove the solder.
1 Remove the solder.
1 Remove the solder.
1 Remove the solder.
1 Remove the solder.
1 Remove the solder.
2 terminal
(module)
2 terminal
(module)
2 terminal (module)
2 terminal (module)
4 module assy (DAB module)
(DAB1)
3 Remove thirty solders.
terminal
(module)
(module)
MAIN board
solder
solder
1.5 mm
module assy (DAB module)
(DAB1)
(DAB1)
7HUPLQDOPRGXOHVHWWLQJ
–
0$,1ERDUGEORFNUHDUWRSYLHZ
–
3 Remove three solders.
long side
notch
short side
Note: When installing the connector
pin 3P (CN405), check the
direction to install.
to module assy
(DAB module) (DAB1)
(DAB module) (DAB1)
to MAIN board
Click on the first or last page to see other XDR-S60DBP service manuals if exist.