Sony XDR-S60DBP Service Manual ▷ View online
XDR-S60DBP
13
10. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
counterclockwise direction, select the “<FM CHECK>”, and
press the [TUNER/SELECT/ENTER] button.
press the [TUNER/SELECT/ENTER] button.
(Displayed characters/values in the following fi gure are example)
<FM CHECK>
01: 87.5MHz
PI:----
Count:-----
FM frequency
11. [VOLUME] jog is turned in the clockwise direction to a maxi-
mum, and checks that the sound is outputted from speaker.
12. Headphone is inserted in headphone jack (J401) and checks
that the sound is outputted from headphone.
13. Volume is lowered and pull out the headphone.
14. Press the [BACK] button, return to the test mode menu.
15. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
14. Press the [BACK] button, return to the test mode menu.
15. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
counterclockwise direction, select the “<KEY CHECK>”, and
press the [TUNER/SELECT/ENTER] button.
press the [TUNER/SELECT/ENTER] button.
16. Whenever any buttons of this unit are pressed and jog of this
unit is turned, the button count decreases.
(Displayed characters/values in the following fi gure are example)
<KEY CHECK>
KEY:MENU
REMAIN:13
COUNT:1
Confirmed key name
Button count
The number which
pressed the same
button continuously
Button count
The number which
pressed the same
button continuously
17. When all buttons are pressed and jog is turned “REMAIN:OK”
appears.
(Displayed characters/values in the following fi gure are example)
<KEY CHECK>
KEY:MENU
REMAIN:OK
COUNT:1
18. Pull out the AC adaptor.
19. Dry battery (SIZE “C”, IEC designation LR14) is set to the
19. Dry battery (SIZE “C”, IEC designation LR14) is set to the
unit.
20. Press the [
?/1
] button to turn the power on.
21. Press the [BACK] button, and checks that there is “
”mark
in the upper right of the liquid crystal display.
22. Press the [
?/1
] button to turn the power off. And it checks that
a liquid crystal display disappears.
4. CURRENT MEASUREMENT AND RTC CHECK
Connection:
ammeter
regulated
DC power
supply
XDR-
S60DBP
voltmeter
battery compartment
Procedure:
1. This unit is dropped 3 times from 3 cm in height, this unit is
1. This unit is dropped 3 times from 3 cm in height, this unit is
shaken, and checks that there are no defects, such as shakiness
and an allophone.
and an allophone.
2. [VOLUME] jog is turned in the counterclockwise direction to
a minimum.
3. Dummy battery is set to the unit, and regulated DC power sup-
ply outputs the voltage of 4.5 V.
4. Enter the test mode.
5. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
5. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
counterclockwise direction, select the “<RTC CHECK>”, and
press the [TUNER/SELECT/ENTER] button.
press the [TUNER/SELECT/ENTER] button.
6. The message “RTC OK” appears on the liquid crystal display.
<RTC CHECK>
RTC...
<RTC CHECK>
RTC OK
7. Press the [BACK] button, return to the test mode menu.
8. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
8. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
counterclockwise direction, select the “<INITIALIZE>”, and
press the [TUNER/SELECT/ENTER] button twice to turn the
power off. And it checks that a liquid crystal display disap-
pears.
press the [TUNER/SELECT/ENTER] button twice to turn the
power off. And it checks that a liquid crystal display disap-
pears.
9. Press the [
?/1
] button to turn the power on.
10. Press the [BACK] button to cancel the DAB auto scan.
11. On the screen of the following fi gure, a back light measures in
11. On the screen of the following fi gure, a back light measures in
the state of on. Press the [BACK] button, when a back light is
off.
off.
--:--
No signal
DAB
It checks that current consumption of DAB function is less
than 195 mA using an ammeter.
than 195 mA using an ammeter.
12. Press the [DAB/FM/AUDIO IN] button to select the FM func-
tion.
13. Press the [BACK] button to cancel the FM auto scan.
14. On the screen of the following fi gure, a back light measures in
14. On the screen of the following fi gure, a back light measures in
the state of on. Press the [BACK] button, when a back light is
off.
off.
--:--
No station list
FM
It checks that current consumption of FM function is less than
210 mA using an ammeter.
210 mA using an ammeter.
15. Press the [
?/1
] button to turn the power off. After the 10 sec-
onds, it checks that current consumption is less than 50 μA
using an ammeter.
using an ammeter.
16. Remove dummy battery.
XDR-S60DBP
14
5. DAB RECEPTION AND AUX CHECK
Procedure:
1. Input the following signal from signal generator to DAB an-
1. Input the following signal from signal generator to DAB an-
tenna input.
Output frequency: 174.928 MHz –49 dBm
2. Dry battery is set to the unit.
3. Telescopic antenna is perpendicularly set to the unit.
4. Enter the test mode.
5. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
3. Telescopic antenna is perpendicularly set to the unit.
4. Enter the test mode.
5. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
counterclockwise direction, select the “<DAB CHECK>”, and
press the [TUNER/SELECT/ENTER] button.
press the [TUNER/SELECT/ENTER] button.
<DAB CHECK>
01:174.928MHz
CER:
6. Headphone is inserted in headphone jack (J401) and checks
that the sound is outputted from headphone.
7. Press the [BACK] button, return to the test mode menu.
8. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
8. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
counterclockwise direction, select the “<AUX CHECK>”, and
press the [TUNER/SELECT/ENTER] button.
press the [TUNER/SELECT/ENTER] button.
<AUX CHECK>
Signal:OFF
9. [VOLUME] jog is turned in the clockwise direction to a maxi-
mum.
10. The sound source (CD etc.) is inputted into the AUDIO IN jack
(J402) of this unit.
11. It checks that the display has changed to “Signal:ON” from
“Signal:OFF”. And the sound is outputted from a speaker, and
checks that there is no defective sound quality.
checks that there is no defective sound quality.
12. Volume is lowered, pull out the headphone and AUDIO IN
connecting cord.
13. Remove dry battery.
6. FM RECEPTION CHECK
Procedure:
1. Input the following signal from signal generator to FM antenna
1. Input the following signal from signal generator to FM antenna
input.
Output frequency: 87.5 MHz
Deviation:
75 kHz/M+S 37 %
Output level:
54 dBuV/m
2. L and R channels are outputted from the signal generator.
3. AC adaptor is inserted in DC IN jack (J101).
4. Enter the test mode.
5. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
3. AC adaptor is inserted in DC IN jack (J101).
4. Enter the test mode.
5. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
counterclockwise direction, select the “<FM CHECK>”, and
press the [TUNER/SELECT/ENTER] button.
press the [TUNER/SELECT/ENTER] button.
(Displayed characters/values in the following fi gure are example)
<FM CHECK>
01: 87.5MHz
PI:----
Count:-----
FM frequency
6. [VOLUME] jog is turned to center, headphone is inserted in
headphone jack (J401) and checks that the sound is outputted
from headphone.
from headphone.
It checks that there is no defect. Monaural, reception cannot be
carried out and sensitivity is weak, etc.
carried out and sensitivity is weak, etc.
7. [VOLUME] jog is turned in the counterclockwise direction to
a minimum. The sound from a headphone becomes small suit-
ably, and checks that there is no defective sound quality.
ably, and checks that there is no defective sound quality.
(Sound is not outputted at the time of a minimum)
8. [VOLUME] jog is turned in the clockwise direction to a maxi-
mum. The sound from a headphone becomes large suitably,
and checks that there is no defective sound quality.
and checks that there is no defective sound quality.
9. Headphone is pull out from the unit. Checks that the unit is
struck 3 times lightly and the sound from a speaker does not
have interruption and defective sound quality.
have interruption and defective sound quality.
10. [VOLUME] jog is turned in the counterclockwise direction to
a minimum. The sound from a speaker becomes small suitably,
and checks that there is no defective sound quality.
and checks that there is no defective sound quality.
(Sound is not outputted at the time of a minimum)
11. [VOLUME] jog is turned in the clockwise direction to a maxi-
mum. The sound from a speaker becomes large suitably, and
checks that there is no defective sound quality.
checks that there is no defective sound quality.
12. The audio connecting cord from an oscilloscope is inserted in
the headphone jack (J401).
13. The stereo waveforms are checked with an oscilloscope.
Example:
L-ch
R-ch
14. R channel is outputted from the signal generator, and R chan-
nel waveform is checked with an oscilloscope.
Example:
L-ch
R-ch
15. L channel is outputted from the signal generator, and L channel
waveform is checked with an oscilloscope.
Example:
L-ch
R-ch
16. The audio connecting cord from an oscilloscope is pull out the
headphone jack (J401).
17. Pull out the AC adaptor.
XDR-S60DBP
15
7. INITIALIZE
After the completion of repair, execute initialization.
All the settings, presets and the list of receivable DAB stations will
be deleted.
After the completion of repair, execute initialization.
All the settings, presets and the list of receivable DAB stations will
be deleted.
Procedure:
1. Dry battery is set to the unit.
2. Press the [
1. Dry battery is set to the unit.
2. Press the [
?/1
] button to turn the power on.
3. Press the [MENU] button, and enter the menu mode.
4. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
4. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
counterclockwise direction, select the “Initialize”.
Menu
Beep
Light
Initialize
5. [TUNER/SELECT/ENTER] jog is turned in the clockwise or
counterclockwise direction, select the “OK”.
Initialize
Cancel
OK
6. The message “Complete” appears on the liquid crystal display,
initializations is completed, and then turn the power off.
7. Remove dry battery.
16
XDR-S60DBP
SECTION 4
EXPLODED VIEWS
1
4-456-836-01 LID, BATTERY CASE (for BLACK)
1
4-456-836-11 LID, BATTERY CASE (for WHITE)
1
4-456-836-21 LID, BATTERY CASE (for RED)
2
4-459-426-01 CUSHION (BATTERY CASE LID B)
(BLACK) . . . (BLACK, RED)
2
4-459-426-11 CUSHION (BATTERY CASE LID B)
(WHITE) . . . (WHITE)
3
3-254-151-01 SCREW (B2.6), (+) P TAPPING
4
4-456-862-01 LID
(CONNECTOR)
5
3-918-696-11 SCREW (M3X6 LOCK ACE)
(SILVER) . . . (WHITE, RED)
5
3-918-696-31 SCREW (M3X6 LOCK ACE) (BLACK) . . . (BLACK)
6
3-252-827-01 SCREW (B2.6), (+) BV TAPPING
(SILVER) . . . (WHITE, RED)
6
3-252-827-11 SCREW (B2.6), (+) BV TAPPING
(BLACK) . . . (BLACK)
7
4-456-858-01 FOOT
8
4-456-844-01 KNOB (VOLUME) (for BLACK)
8
4-456-844-11 KNOB (VOLUME) (for WHITE)
8
4-456-844-21 KNOB (VOLUME) (for RED)
9
4-457-930-01 SPRING
(KNOB)
10
A-1949-142-A KNOB (TUNE) ASSY (B) (for BLACK)
10
A-1949-143-A KNOB (TUNE) ASSY (W) (for WHITE)
10
A-1949-144-A KNOB (TUNE) ASSY (R) (for RED)
ANT1 1-754-856-21 ANTENNA,
TELESCOPIC
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “
*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
Parts Color Cabinet’s Color
4-1. OVERALL SECTION
• Rear view
The components identifi ed by mark
0
or dotted line with mark
0 are critical for
safety.
Replace only with part number specifi ed.
Replace only with part number specifi ed.
cabinet (rear) section
8
9
6
6
5
6
6
6
6
2
2
7
10
7
7
7
6
cabinet (front) section
ANT1
3
4
1
• Color variations
AEP model
AEP model
: Black, White, Red
UK model
: Black, White, Red
Australian model : Black, White
Click on the first or last page to see other XDR-S60DBP service manuals if exist.