Sony XDR-S10HDIP Service Manual ▷ View online
XDR-S10HDiP
29
IC311 TDA7266P13TR (POWER Board)
IC901 XC6213B332MR (POWER Board)
VIN 1
CE 3
VSS 2
NC
4
VOUT
5
+
–
–
ON/OFF
CONTROL
CURRENT
LIMIT
VOLTAGE
REFERENCE
P-GND
24
NC
23
NC
22
NC
21
+LOUT
–LOUT
20
P-GND 1
NC 2
NC 3
NC 4
NC 3
NC 4
NC 12
ST-BY 11
MUTE 10
NC 9
+ROUT 5
–ROUT 6
–ROUT 6
VCC
VCC
7
R-IN
Vref
8
19
L-IN
17
NC
16
NC
15
S-GND
14
NC
13
VCC
VCC
18
XDR-S10HDiP
30
• IC Pin Function Description
MICON BOARD IC401 R5F3640MDFAR (SYSTEM CONTROL, LCD DRIVE)
Pin No.
Pin Name
I/O
Description
1
SOUT NC
—
Not used (Open)
2
CLK4 NC
—
Not used (Open)
3
P9_4 RMT
I
Remote control signal input
4
P9_3 NC
—
Not used (Open)
5
P9_2 NC
—
Not used (Open)
6
P9_1 NC
—
Not used (Open)
7
P9_0 NC
—
Not used (Open)
8
BYTE
I
External data bus input. (Connected to ground)
9
CNVSS
I
Change processor mode input
10
XCIN
I
System sub clock signal input (32.0 kHz)
11
XCOUT
O
System sub clock signal output (32.0 kHz)
12
RESET
I
System reset signal input
13
XOUT
O
System main clock signal output (5.53 MHz)
14
VSS
—
Ground
15
XIN
I
System main clock signal input (5.53 MHz)
16
VCC1
—
Power supply (+3.3 V)
17
NMI
I
NMI interruption signal input (Not used) (Pull up)
18
INT2 VDET
I
LED+B detection signal input
19
INT1 DTUNER_RDS
I
RDS data interruption signal input
20
INT0 NC
—
Not used (Open)
21
P8_1 CLOCK SHIFT
I
Control pin for system main clock frequency shift. (Not used)
22
P8_0 NC
—
Not used (Open)
23
P7_7 NC
—
Not used (Open)
24
P7_6 NC
—
Not used (Open)
25
P7_5 NC
—
Not used (Open)
26
P7_4 LIGHT1
O
LCD back light control signal output
27
P7_3 LIGHT2
O
LCD back light control signal output
28
TA10OUT/V BEEP
O
Beep signal output
29
RXD2/DTUNER_SCL
O
Serial clock output to D-Tuner.
30
TXD2/DTUNER_SDA
O
Serial data output to D-Tuner.
31
P6_7/TXD1
O
Serial data output to iPod
32
P6_6/RXD1
I
Serial data input from iPod
33
P6_5/CLK1
I
Serial clock input for serves jig
34
P6_4/RTS1
I
RTS signal input for serves jig
35
DMP_TXD_SDA0
I/O
EEPROM serial data input/output
36
DMP_RXD_SCL0
O
EEPROM serial clock signal output
37
P6_1 DTUNER_RESET
O
D-Tuner reset signal output
38
P6_0/NC
—
Not used (Open)
39
P5_7/NC
—
Not used (Open)
40
P5_6 32k_OUT
—
Not used (Open)
41
P5_5/EPM
—
Not used (Open)
42
P5_4 3.3V DETECT
I
+B (+3.3V) detection signal input
43
P5_3 DMP_POWER
O
IPod power control signal output
44
P5_2 DMP_DETECT0
I
IPod connected signal input
45
P5_1 DTUNER_
POWER
O
D-Tuner power control signal output
46
P5_0/CE
—
Not used (Open)
47
P4_7/CSB
O
LCD chip select signal output
48
P4_6/RST
O
LCD reset signal output
49
P4_5/A0
O
LCD address A0 signal output
50
P4_4/WRB
O
LCD data Write signal output
51
P4_3/RDB
O
LCD data read signal output
52
P4_2/NC
O
Not used (Open)
XDR-S10HDiP
31
Pin No.
Pin Name
I/O
Description
53
P4_1/NC
O
Not used (Open)
54
P4_0/NC
O
Not used (Open)
55
P3_7/D0
O
LCD data D0 output
56
P3_6/D1
O
LCD data D1 output
57
P3_5/D2
O
LCD data D2 output
58
P3_4/D3
O
LCD data D3 output
59
P3_3/D4
O
LCD data D4 output
60
P3_2/D5
O
LCD data D5 output
61
P3_1/D6
O
LCD data D6 output
62
VCC2
—
Power supply (BUP+3.3V)
63
P3_0/D7
O
LCD data D7 output
64
VSS
—
Ground
65
P2_7 SHIMUKE2
I
Destination select input (Pull down)
66
P2_6 NC
—
Not used (Open)
67
P2_5 NC
—
Not used (Open)
68
P2_4 NC
—
Not used (Open)
69
P2_3 NC
—
Not used (Open)
70
P2_2 NC
—
Not used (Open)
71
P2_1 NC
—
Not used (Open)
72
P2_0 NC
—
Not used (Open)
73
P1_7 NC
—
Not used (Open)
74
P1_6 NC
—
Not used (Open)
75
P1_5 AUTH_RESET
O
Reset signal output
76
P1_4 NC
—
Not used (Open)
77
P1_3 SDA
I/O
FLASH ROM serial data input/output
78
P1_2 SCL
O
FLASH ROM serial clock signal output
79
P1_1 NC
—
Not used (Open)
80
P1_0 NC
—
Not used (Open)
81
P0_7 FAN CONT
O
FAN control signal output
82
P0_6 AUDIO_
STANDBY
O
P-AMP standby signal output
83
P0_5 AUDIO_MUTE
O
P-AMP mute signal output
84
P0_4 VOL_CLK
O
Serial clock output to electric volume
85
P0_3 NC
—
Not used (Open)
86
P0_2 VOL_DATA
O
Serial data output to electric volume
87
P0_1 DMP_MUTE
O
IPod audio mute signal output
88
P0_0 NC
—
Not used (Open)
89
P10_7 TEST1
—
Not used (Open)
90
P10_6 TEST2
—
Not used (Open)
91
P10_5 TEST3
—
Not used (Open)
92
P10_4 TEST4
—
Not used (Open)
93
P10_3 TAG LED_CTL
O
Tag LED drive signal output
94
AN2 KEY2
I
Key input
95
AN1 KEY1
I
Key input
96
AVSS
—
Ground
97
P10_0/KEY OFF
O
+B control signal output
98
VREF
I
Reference voltage (+3.3V)
99
AVCC
—
Power supply (BUP+3.3V)
100
SIN4 NC
—
Not used (Open)
32
XDR-S10HDiP
SECTION 4
EXPLODED VIEWS
1
3-254-143-11 SCREW (B3), (+) BV TAPPING
2
3-285-550-01 CABINET
(REAR)
3
2-667-344-01 FOOT,
RUBBER
4
A-1547-623-A FAN CONNECTIONG BOARD, COMPLETE
5
3-254-151-01 SCREW (B2.6), (+) P TAPPING
6
3-285-563-01 CUSHION
(SP)
7
3-873-770-01 LID
(CONNECTOR)
0 M980
1-787-396-11 D.C. FAN (50 SQUARE)
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
4-1. CABINET (REAR) SECTION
Note:
• -XX and -X mean standardized parts, so
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
original one.
• Items marked “*” are not stocked since
they are seldom required for routine ser-
vice. Some delay should be anticipated
when ordering these items.
vice. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not sup-
plied.
plied.
• Color Indication of Appearance Parts Ex-
ample:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet’s Color
• Accessories are given in the last of the
electrical parts list.
The components identifi ed by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specifi ed.
or dotted line with mark 0 are critical for
safety.
Replace only with part number specifi ed.
1
1
1
1
1
1
2
4
5
6
6
6
M980
cabinet (upper) section
cabinet (front) section
5
7
3
Click on the first or last page to see other XDR-S10HDIP service manuals if exist.