DOWNLOAD Sony TA-F501ES Service Manual ↓ Size: 7.31 MB | Pages: 68 in PDF or view online for FREE

9

Note: Follow the disassembly procedure in the numerical order given.

• This set can be disassembled in the order shown below.

3-1.

TOP PLATE,
SIDE PLATE
(Page 9)

SET

3-2.

POWER BOARD
(Page 10)

3-3.

FRONT PANEL ASSY
(Page 10)

3-4.

MAIN BOARD
(Page 11)

1

 two flat head screws (TP)

2

 two flat head screws (TP)

8

 two flat head screws (TP)

7

 two flat head screws (TP)

4

 two flat head screws (TP)

5

 two flat head screws (TP)

3

 top plate

6

 side plate (L)

9

 side plate (R)

10

qa

 three screws

     (+BVTP 3

 

×

 8)

qd

 three screws

     (+BVTP 3

 

×

 8)

qs

 screw  (+BVTT 3 

×

 6)

8

 two screws

     (+BVTP 3

 

×

 8)

9

 two screws

     (+BVTP 3

 

×

 8)

0

 bracket (power MT)

1

 CN11 (4P)

2

 CN1 (2P)

4

 CNP95 (3P)

6

 CNP98 (3P)

7

 CNP97 (6P)

3

 CNP96 (2P)

5

 CNP99 (5P)

qf

 POWER board

4

 two screws

     (+BVTP 3

 

×

 8)

5

 three screws

     (+BVTP 3

 

×

 8)

6

 front panel assy

1

 CNP2001 (6P)

2

 CNP2011 (13P)

3

 CNP1401 (15P)

11

2

 two screws

     (+BVTT 3

 

×

 6)

8

 two screws

     (+BVTP 2.6 (3CR))

9

 two screws

     (+BVTP 2.6 (3CR))

0

 DSP board

qa

 MAIN board

4

 five screws

     (+BVTT 3

 

×

 5)

7

5

 two screws

     (+BVTP 3

 

×

 8)

6

 five screws

     (+BVTP 3

 

×

 8)

3

 heat sink assy

1

 CN1005 (5P)

12

Items

Protector on/off

Model version display

Model/destination change

FM/AM tuner version display

HDMI controller version
display

HDMI controller update mode

Speaker output setting

FL display fonts test

FL display test

Audio swap mode

DSP halt

DSP Version display

Volume value display (FL/FR)

Volume value display (SL/SR)

Volume value display (CT/SW)

Display

PROTECTOR ON/OFF [XXX]

##### *** vX. XX @@@@

MODEL [##### * * * *] X X

FM/AM Tuner Ver X. XX

HDMI Micom Ver X. XX

HDMIUcom Update [XXX]

SPEAKER OUT XXXXX

FL FONT 0x** = [X]

ALL ON

SWAP [XXXXXXXXXXX]

DSP HALT [XXX]

DSP Ver S: ***, P: XXX

FL**** FR XXXX

SL**** SR XXXX

CT**** SW XXXX

Remark

“ON”: Power supply will cut in 5 seconds when the protector
works.

“OFF”: Power supply doesn't cut when the protector works.

Note:It is not possible to set it to ON until turning off power when

the protector setting is set to OFF. Turn on the power supply
again when setting it to ON.

XXX: ON or OFF (It switches by pressing the  

U  u  key of the

remote commander after the item is fixed pressing the [ENTER] key
of the remote commander)

#####: model
***: destination
X.XX: main system controller software version
@@@@: Sum value of flash memory in the main system controller

Not used

Not used

Not used

Not used

XXXXX: Selection of speaker output audio
[SOURCE]: nomally mode, [MIC]: mode that output audio from
mic from speaker (It switches by pressing the  

U  u  key of the

remote commander after the item is fixed pressing the [ENTER] key of
the remote commander)

All the fonts to be displayed on the FL display can be checked.
**: hexadecimal character code. (It switches by pressing the  

U  u

key of the remote commander after the item is fixed pressing the
[ENTER] key of the remote commander.)
X: character corresponding to the specified code.

All segment is display

Not used

XXX: ON or OFF (It switches by pressing the  

U  u  key of the

remote commander after the item is fixed pressing the [ENTER] key
of the remote commander)
Mode not to send DSP host code, and to make only decipherment
done

***: DSP decoder patch version
XXX: DSP post process version

****: Front L-ch volume value
XXXX: Front R-ch volume value

Not used

Not used

All preset contents are cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair.
Procedure:

1. While pressing the [MUTING] button, press the [POWER] button to turn on the main power.
2. The message “MEMORY CLEARING...” appears and the memories are reset to the default values.
3. When done, the message “MEMORY CLEARED !” appears.

1. Press the [POWER] button to turn on the main power and press the [MUTING] button for more than 5 seconds.
2. The message “MENU SPECIALIZED!” appears.
3. When  

U  u  key of the remote commander is pressed, the message “SPECIAL” appers.

4. The item of special menu mode is selected pressing  

U  u  key of the remote commander after [ENTER] key of the remote commander

is pressed.

5. To release from this mode, press the [MUTING] button for more than 5 seconds. The message “MENU SPECIALIZED OFF” appears

upon exiting from this mode.

Note 1: Turn on the power supply again when usually operating after it changes in special menu mode.
Note 2: The setting remains even if coming off the menu. The setting is cleared when turning off power.