DOWNLOAD Sony SS-CT1100D / SS-GN1100D / SS-RSX1100D / SS-WGV1100D Service Manual ↓ Size: 303.41 KB | Pages: 10 in PDF or view online for FREE

E Model

2007D02-1
© 2007.04

Photo : SS-CT1100D

Photo : SS-GN1100D

Photo : SS-RSX1100D

Photo : SS-WGV1100D

•

JIG
When disassembling the set, use the following jig (for
front panel removal).
Part No.: J-2501-238-A  JIG FOR SPEAKER REMOVAL

DVD PLAYER DECK
RECEIVER

CENTER SPEAKER
SUB WOOFER

FRONT SPEAKERS

SS-GN1100D

SURROUND SPEAKERS

SS-RSX1100D

System name

MHC-GN1100D

SS-GN1100DP

HCR-GN1100D

SS-CT1100D

SS-WGV1100D

HCD-GN1100D

2

Speaker system

2-way, 2-unit, bass-reflex type,
magnetically shielded

Speaker units
Woofer:

20 cm, cone type

Tweeter:

2.5 cm, horn type

Nominal impedance

6 ohms

Dimensions (w/h/d)

Approx. 281 

×

 415.2 

×

 313 mm

Mass

Approx. 7.2 kg net per speaker

Speaker system

2-way, 2-units, bass-reflex type

Speaker units
Woofer:

10 cm, cone type

Tweeter:

5 cm, horn type

Nominal impedance

6 ohms

Dimensions (w/h/d)

Approx. 176 

×

 361.7 

×

 222.5 mm

Mass

Approx. 2.9 kg net per speaker

Speaker system

Full range, 2-unit, bass-reflex
type, magnetically shielded

Speaker units
Full range:

8 cm, cone type 

×

 2

Nominal impedance

6 ohms

Dimensions (w/h/d)

Approx. 268 

×

 107 

×

 117 mm

Mass

Approx. 1.6 kg

Subwoofer system

1-way, 1-unit, bass-reflex type,
magnetically shielded

Speaker units
Subwoofer:

25 cm, cone type

Nominal impedance

8 ohms

Dimensions (w/h/d)

Approx. 351 

×

 415.2 

×

 350.2 mm

Mass

Approx. 8.9 kg

Design and specifications are subject to change without notice.

3

SUBWOOFER

LEVEL

SW1400

SUBWOOFER

ON/OFF

HCD-GN1100D

11

(11)

1-872-864-

S1400

Q1400

R1405

R1406

JR1400

D1400

C1400

CN1400

1

4

E

JR1402

C1401

R1401

0dB
-3dB
-6dB
-12dB

R1402

R1403
R1404

Note on Printed Wiring Boards:
•

X

: parts extracted from the component side.

•

: Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

• Indication of transistor.

B

These are omitted.

C

E

Q

Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40

°

C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°

C.

Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

4

Note on Schematic Diagram:
• All capacitors are in 

µ

F unless otherwise noted.  (p: pF) 50 WV or

less are not indicated except for electrolytics and tantalums.

• All resistors are in 

Ω

 and 

1

/

4 

W or less unless otherwise specified.

•

C

: panel designation.

•

A

: B+ Line.

• Voltages are dc with respect to ground in service mode.

no mark : POWER ON

• Voltages are taken with a VOM (Input impedance 10 M

Ω

).

Voltage variations may be noted due to normal production toler-
ances.

JR1400

C1400

R1406

R1405

R1401

R1402

R1403

R1404

JR1402

C1401

1

50V

D1400

Q1400

S1400

SW1400

CN1400

0

10

50V

1k

1k

2.2k

6.8k

22k

68k

0

SELU5420E

GREEN

2SC2712

LED DRIVE

4P

SUBWOOFER

SUBWOOFER

ON/OFF

SUBWOOFER

ON/OFF

LEVEL

HCD-GN1100D