DOWNLOAD Sony STR-DN2010 Service Manual ↓ Size: 10.39 MB | Pages: 126 in PDF or view online for FREE

UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with 

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.
•  Unleaded solder melts at a temperature about 40 °C higher 

than ordinary solder.

 

Ordinary soldering irons can be used but the iron tip has to be 
applied to the solder joint for a slightly longer time.

 

Soldering irons using a temperature regulator should be set to 
about 350 °C.

 

Caution: The printed pattern (copper foil) may peel away if  
 

the heated tip is applied for too long, so be careful!

• Strong 

viscosity

 

Unleaded solder is more viscous (sticky, less prone to fl ow) 
than ordinary solder so use caution not to let solder bridges 
occur such as on IC pins, etc.

•  Usable with ordinary solder
 

It is best to use only unleaded solder but unleaded solder may 
also be added to ordinary solder.

NOTE  OF  REPLACING  THE  IC3500  AND  IC3501  ON  
THE  D-VIDEO  BOARD
IC3500 and IC3501 on the D-VIDEO board cannot exchange with 
single. When these parts on the D-VIDEO board are damaged, ex-
change the entire mounted board.

NOTE  OF  REPLACING  THE  IC8001  AND  IC8013  ON  
THE  NETWORK  HUB  BOARD
IC8001 and IC8013 on the NETWORK HUB board cannot ex-
change with single. When these parts on the NETWORK HUB 
board are damaged, exchange the entire mounted board.

If there is a malfunction, the display shows a 
message. You can check the condition of the 
system by the message. See the following table 
to solve the problem. If any problem persists, 
consult your nearest Sony dealer. 

Irregular current is output to the speakers, or 
upper panel of the receiver is covered with 
something. The receiver will automatically 
turn off after a few seconds. Check the 
speaker connection and turn on the power 
again.

For other messages, see “Message list after 
Auto Calibration measurement”, “DIGITAL 
MEDIA PORT message list” and “Satellite 
radio message list”. 

Before using the receiver for the first time, 
initialize the receiver by performing the 
following procedure. This procedure can also 
be used to return settings you have made to 
their initial settings. 
Be sure to use the buttons on the receiver for 
this operation.

?/1 to turn off the 

?/1 to turn on the 

After “CLEARING” appears on the 
display for a while, “CLEARED!” 
appears.
All the settings you have changed or 
adjusted are reset to the initial settings.

It takes about 30 seconds for the memory to be 
cleared completely. Do not turn the receiver off until
“CLEARED!” appears on the display.

?/1

MUSIC

MUTING

Be sure to use the buttons on the receiver for 
this operation.

?/1 to turn off the 

?/1.

“S.F. CLEAR” appears on the display and 
all sound fields are reset to their initial 
setting.

?/1

MUSIC

•  This set can be disassembled in the order shown below.

Note: Follow the disassembly procedure in the numerical order given.

4

3

5

5

2

u 8)

6

1

u 8)

A

E

E

F

F

D

D

B

C

A

C

B

1

2

3

4

5

9

ql

6

qd

wa

w;

qj

7

u 8)

8

u 8)

0

u 8)

qa

u 6 (S))

qs

u 8)

qh

u 8)

qf

qg

qk

u 8)

3

7

6

8

u 8)

q;

qa

1

2

5

4

9

1

4

5

2

3

G

G

H

H

6

u 8)

8

u 8)

7

u 8)

9

u 8)

qs

u 8)

qa

qf

qd

0