Sony STR-DN2010 Service Manual ▷ View online
STR-DN2010
17
SECTION 4
ELECTRICAL ADJUSTMENT
VIDEO CALIBRATION ADJUSTMENT
Adjustment to decide the standard of the video input signal.
Note: After replacing DIGITAL VIDEO board, or after “RESET” of the
special menu mode is executed, perform this adjustment.
1. Adjustment jig
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substi-
tute it by the Blu-ray Disc player that can output the component
terminal and the video terminal at the same time (Substitution
model name example: BDP-S350).
However, please do the following signal output confi rmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substi-
tute it by the Blu-ray Disc player that can output the component
terminal and the video terminal at the same time (Substitution
model name example: BDP-S350).
However, please do the following signal output confi rmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
2. Video calibration adjustment
2-1. Connection
2-1. Connection
color pattern
generator
or
Blu-ray
Disc player
set
HDMI TV
OUT
ANALOG VIDEO board
COMPONENT
COMPONENT
VIDEO
ASSIGNABLE
(INPUT ONLY) COMPO 1 IN jack
BD VIDEO IN jack
2-2. Procedure for color pattern generator
1. It connects of step 2-1, and the turn on the main power.
2. “BD” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern genera-
1. It connects of step 2-1, and the turn on the main power.
2. “BD” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern genera-
tor.
4. Press the [POWER] button to turn off the main power.
5. While pressing the [MOVIE] and [DISPLAY] buttons, press
5. While pressing the [MOVIE] and [DISPLAY] buttons, press
the [POWER] button to turn on the main power. When cor-
rectly entering the test mode “FIN _:_:_” is displayed (keeps
pressing two buttons until the message appears).
rectly entering the test mode “FIN _:_:_” is displayed (keeps
pressing two buttons until the message appears).
6. The NTSC signal adjustment is begun when press the cross
(center of cursor) button of remote commander, and the dis-
play changes from “N:MWX_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, the display returns to the display of
“FIN N:_:_”.
play changes from “N:MWX_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, the display returns to the display of
“FIN N:_:_”.
7. Input PAL color bars signal from the color pattern generator.
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color
pattern generator.
10. Perform step 6 to 7 for the HD signal adjustment.
11. The turn off the main power.
11. The turn off the main power.
2-3. Procedure for Blu-ray Disc player
1. It connects of step 2-1, and the turn on the main power of set
1. It connects of step 2-1, and the turn on the main power of set
and Blu-ray Disc player.
2. “BD” is selected by using [INPUT SELECTOR] dial.
3. Press the OPEN/CLOSE button of the Blu-ray Disc player,
3. Press the OPEN/CLOSE button of the Blu-ray Disc player,
and DVD test disc “HLX-504 (Part No. J-6090-088-A)” or
“HLX- 513 (Part No. J-2501-305-A)” is insert. The disc play-
back automatically becomes start “Main Menu” is display.
“HLX- 513 (Part No. J-2501-305-A)” is insert. The disc play-
back automatically becomes start “Main Menu” is display.
4. “1.Color Bar 100%” of “1.Video Signal” is reproduced, and
100% in the color bar is displayed in the TV monitor, playing
the Blu-ray Disc player is pause playback.
the Blu-ray Disc player is pause playback.
5. Press the [POWER] button to turn off the main power of the
set.
6. While pressing the [MOVIE] and [DISPLAY] buttons,
press the [POWER] button to turn on the main power of the
set. When correctly entering the test mode “FIN _:_:_” is
displayed (keeps pressing two buttons until the message ap-
pears).
set. When correctly entering the test mode “FIN _:_:_” is
displayed (keeps pressing two buttons until the message ap-
pears).
7. The NTSC signal adjustment is begun when press the cross
(center of cursor) button of remote commander, and the dis-
play changes from “N:MWX_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, the display returns to the display of
“FIN N:_:_”.
play changes from “N:MWX_ _ _ _ _” to “N:MWoCDV_ _”
little by little. Finally, the display returns to the display of
“FIN N:_:_”.
8. Press the OPEN/CLOSE button of the Blu-ray Disc player,
and change to DVD test disc “HLX-506 (Part No. J-6090-
077-A)” or “HLX-507 (Part No. J-6090-078-A)”. The disc
playback automatically becomes start “Main Menu” is dis-
play.
077-A)” or “HLX-507 (Part No. J-6090-078-A)”. The disc
playback automatically becomes start “Main Menu” is dis-
play.
9. “1.Color Bar 100%” of “1.Video Signal” is reproduced, and
100% in the color bar is displayed in the TV monitor, playing
the Blu-ray Disc player is pause playback.
the Blu-ray Disc player is pause playback.
10. The PAL signal adjustment is begun when press the cross
(center of cursor) button of remote commander. Finally, the
display returns to the display of “FIN N:P:_”.
display returns to the display of “FIN N:P:_”.
11. Press the OPEN/CLOSE button of the Blu-ray Disc player,
and change to DVD test disc “HLX-104 (Part No. J-6090-
199-A)”. The disc playback automatically becomes start
“Main Menu” is display.
199-A)”. The disc playback automatically becomes start
“Main Menu” is display.
12. “59.94Hz, 1080i” → “1.Video Signal” → “1.Color Bar
100%” is selected, and 100% in the color bar is displayed
in the TV monitor, playing the Blu-ray Disc player is pause
playback.
in the TV monitor, playing the Blu-ray Disc player is pause
playback.
13. The video output of the Blu-ray Disc player is switched 1080i
(The output from the component terminal of the Blu-ray Disc
player becomes 1080i output).
player becomes 1080i output).
14. The HD signal adjustment is begun when press the cross
(center of cursor) button of remote commander. Finally, the
display returns to the display of “FIN N:P:H”.
display returns to the display of “FIN N:P:H”.
15. The turn off the main power.
STR-DN2010
18
FM AUTO STOP CHECK
signal
generator
set
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM
1. Turn on the set.
2. Input the following signal from signal generator to FM
antenna input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation
Deviation
: 75 kHz
Modulation
: 1 kHz
ANT input
: 35 dBu (EMF)
Note: Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confi rm that input frequency of A, B and C are detected and
automatic scanning stops.
When the station signal is received in good condition, automatic
scanning stops.
scanning stops.
STR-DN2010
STR-DN2010
19
19
5-1. BLOCK DIAGRAM - DIGITAL AUDIO/TUNER Section -
SECTION 5
DIAGRAMS
SYSTEM CONTROLLER
IC2501 (1/5)
DIGITAL OPTICAL
RECEIVE
IC2004
OPTICAL
IN
TV
DIGITAL AUDIO
INTERFACE RECEIVER
IC2006
J2000
A/D CONVERT
IC2012
SELECTOR
IC3801
RDATA
SAT/CATV
IN
SCHMITT
TRIGGER
IC2015
BD
IN
DVD
IN
OPTICAL
COAXIAL
DIGITAL
(ASSIGNABLE)
21
XMCK
DIR_DO
R-CH
27
DOUT 9
RBCK
DIR_BCK
17
BCK
8
VinL
13
VinR
14
LRCK
7
SCKI
6
RX5/VI 9
OUT2
5
RLRCK
DIR_LRCK
20
RMCK
DIR_MCK
16
DIR_SIA
DIR_SIA, DIR_BCK,
DIR_LRCK, DIR_MCK
SIB
RX0
2
2
3
RX4
8
RX3
5
RX2
4
RX6/UI
10
XIN
DO
29
37
83
XI
43
EEPROM_SDA 170
EEPROM_SCL 172
THERMAL1(N) 49
THERMAL2(N) 48
XO
42
3
5
91
14
18
55
76
57
DMPORT_UART_MU/DM
150
DMPORT_UART_DM/MU
151
DMPORT_DETECT
DIR_ERROR
RERR
36
84
DIR_CKST
CKST
34
85
SDA
5
SCL
6
2
2
2
COM1_DATA
DI
38
100
COM1_CLK
CL
40
99
DIR_CE-LAT
CE
39
82
DIR_XMODE-RESET
XMODE
41
81
XOUT
28
SPDIF
AMPLIFIER
IC6702
AUDIO INPUT
SELECTOR
IC2600 (1/2)
VIDEO SIGNAL
PROCESSOR
IC6014 (1/3)
DIR FUNCTION
SELECT
IC400 (1/3)
AUDIO /VO 33
DIR_NON_AU
DIR_ERR
COM_CLK
COM_DATA
COM_CLK, COM_DATA
DM_L
V2_L/Main_Zone_L
ADC LOUT
DM_L/Zone_2_L
DM_VIDEO
X2001
24.576MHz
CN6701
17
VIDEO
5
RXD
6
TXD
7
DET
13
L+
14
R+
R-CH
DMPORT
X2501
4MHz
EEPROM
IC2502
THERMAL
SENSOR
IC252
THERMAL
SENSOR
IC251
THERMAL
SENSOR
IC250
TUNER (FM/AM)
TN 1
FM ANT
AM ANT
TUN_L
TUN_R
TUN_DO
R-CH
RDS_DATA
RDS_CLK
TUN_DAT
TUN_CLK
TUN_CLK
TUN_CE
111 TUN_DO(MISO)
TUN_TUNED
115 TUNED
RDS_DATA
RDS_CLK-INT
RDS_CLK-INT
TUN_DATA(MOSI)
TUN_CLK
TUN_LAT
TUN_CLK
TUN_LAT
(ECE, UK)
(ECE, UK)
(US)
Abbreviation
: Continental European, East European and Russian models
ECE
DIGITAL OPTICAL
RECEIVE
IC2003
DIGITAL OPTICAL
RECEIVE
IC2002
AM
FM75
:
COAXIAL
ANTENNA
113
112
114
112
114
110
116
116
152
A
HDMI SECTION
(Page 23)
C
D
B
E
DSP
SECTION
(Page 20)
(Page 20)
DSP
SECTION
(Page 20)
(Page 20)
DSP
SECTION
(Page 20)
(Page 20)
DSP
SECTION
(Page 20)
(Page 20)
DSP
SECTION
(Page 20)
(Page 20)
F
6LJQDOSDWK
5FKLVRPLWWHGGXHWRVDPHDV/FK
: AUDIO (DIGITAL)
: AUDIO (ANALOG)
: TUNER
: VIDEO
: VIDEO
STR-DN2010
STR-DN2010
20
20
5-2. BLOCK DIAGRAM - DSP Section -
CN2213
4
8
6
SIRIUS
CN1302
15
14
26
27
16
19
7
18
11
12
20
25
WIRELESS
TRANSMITTER
4
LEVEL SHIFT
IC2693
4
LEVEL SHIFT
IC2691
4
LEVEL SHIFT
IC2694
G
HDMI
SECTION
(Page 23)
(Page 23)
D
DIGITAL
AUDIO/TUNER
SECTION
(Page 19)
(Page 19)
C
DIGITAL
AUDIO/TUNER
SECTION
(Page 19)
(Page 19)
I
AMP
SECTION
(Page 21)
(Page 21)
F
DIGITAL
AUDIO/TUNER
SECTION
(Page 19)
(Page 19)
B
DIGITAL AUDIO/TUNER SECTION
(Page 19)
E
DIGITAL AUDIO/TUNER SECTION
(Page 19)
H
HDMI SECTION
(Page 23)
DIR_LRCK
DIR_SIA, DIR_BCK,
DIR_LRCK, DIR_MCK
DIR_LRCK, DIR_MCK
DIR_BCK
DIR_MCK
SD1
SD0
DIR_SIA
SD0 – SD3, HDMI_BCK,
HDMI_LRCK, HDMI_MCK
HDMI_LRCK, HDMI_MCK
SI_B
DIR_NON_AU
HDMI_ERROR
DSP
IC5001
AXR0[11]
/AXR1[2]
/AXR1[2]
131
AXR0[12]
/AXR1[1]
/AXR1[1]
134
ACLKR0
AFSR0
AFSR0
AXR0[13]
/AXR1[0]
/AXR1[0]
135
SD2
AXR0[14]
/AXR2[1]
/AXR2[1]
137
SD3
AXR0[15]
/AXR2[0]
/AXR2[0]
138
AXR0[0] 113
AXR0[2] 116
AXR0[7]/
SPI1_CLK
122
AXR0[10]
/AXR1[3]
/AXR1[3]
AXR0[5]
/SPI1_SCS#
/SPI1_SCS#
130
SPI0_SOMI/I2C0_SDA
120
D/A CONVERTER
IC2024
R-CH
2
SO
5
SI
6
SCK
1
CE#
21
HDMI_ERROR
108 FS_RATE1-CAP
80
DSP_SIA_ZERO#
111
DSP_SPIO_MISO
SPI0_SIMO
110
DSP_SPIO_MOSI
SPI0_CLK/I2C0_SCL
108
DSP_SPIO_CLK
SPI0_SCS#/I2C1_SCL
107
DSP SPIO_CE(A36)
7
HOLD#
DSP_SFLASH_HOLD(A36)
AXR0[6]/SPI1_ENA#
OUT
OUT
OUT
121
DSP_INT(A36)
RESET#
14
DSP_RESET(A36)
SERIAL FLASH
IC5003
(US)
EM_D[0] –
EM_D[15]
EM_CLK 70
VO2L 23
R-CH
VO2R 24
R-CH
VO4R 20
VO3L 25
VO3R 26
VO1L 21
VO4L 19
MD/DATA 13
MC/CLK 12
DAC_C
DAC_C, DAC_SL,
DAC_SBL, DAC_FL,
DAC_SW
DAC_SL
DAC_SBL
DAC_FL
COM_CLK
COM_CLK, COM_DATA
COM_DATA
SD-RAM
IC5002
CLK
DQ0 – DQ15
EM_A[0] –
EM_A[11]
A0 – A11
38
EM_CKE 71
CKE
37
EM_CS[0]# 97
CS#
19
EM_RAS# 98
RAS#
18
EM_CAS# 37
CAS#
17
EM_WE# 38
WE#
16
EM_BA[0] 96
BA0
20
EM_BA[1] 94
BA1
21
EM_WE_DQM[0] 39
LDQM
15
EM_WE_DQM[1] 67
UDQM
39
SYSTEM CONTROLLER
IC2501 (2/5)
OSCIN
23
OSCOUT
24
X5001
25MHz
SIGNAL SELECTOR
IC2212
Q
D
CK
5
2
1
MUTING
CONTROL
IC2009
6
SWITCHING
IC2023
LEVEL SHIFT
IC2014
B0
Y0
Y1
Y2
Y3
Y1
Y2
Y3
DIN4
DIN1
DIN3
DIN2
DIN1
DIN3
DIN2
B1
A3
2
5
6
3
11
13
8
8
7
10
9
MUTING
IC2011
2C0
1C0
1Y
Y2
Y2
10
6
7
9
9
SIGNAL SELECTOR
IC2236
2C0
1C0
1C0
1Y
10
6
7
SIGNAL SELECTOR
IC2214
1C0
2C1
1Y
6
DIR_ERR
2C0
10
11
BUFFER
IC2007
Q4B
7
139
141
141
2C1
HDMI_MCK
11
8
6LJQDOSDWK
6LJQDOSDWK
: AUDIO (ANALOG)
: AUDIO (DIGITAL)
: AUDIO (DIGITAL)
B1
1 S
1 IN
10 B2
13
4
B3
BCK1
LRCK1
SD2
SD3
SD1
I2C_SDA
INT
I2C_SCL
RESET
ADC_SEL
SRC_MUTE
6$LU'HWHFW
Y0
7
Y1
9
Y2
12
Y3
4
OUT
LINE AMP
IC2027
LINE AMP
IC2026
LINE AMP
IC2025
LINE AMP
IC2028
VO1R 22
DAC_SW
101
S_AIR_SELECT(N)
4
DIG_AU_DATA_MUTE
79
S-AIR_I2C_SDA(N)
5
S-AIR_INT(N)
6
S-AIR_I2C_SCL(N)
7
S-AIR_SRC_RESET(N)
166
S-AIR_ADC_SEL(N)
167
S-AIR_SRC_MUTE(N)
168
S-AIR_DETECT(N)
169
93 92 94 107
SIRIUS_POWER_ENABLE
124
SIRIUS_UART_SI/MU
123
SIRIUS_UART_MU/SI
122
103 106
1C1
2C1
HDMI_BCK
HDMI_LRCK
5
11
D2002
CEC DATA
SWITCH
Q2001 - 2002
Click on the first or last page to see other STR-DN2010 service manuals if exist.