DOWNLOAD Sony STR-DN1010 Service Manual ↓ Size: 7.06 MB | Pages: 102 in PDF or view online for FREE

Model
STR-DN1010
Pages
102
Size
7.06 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
str-dn1010.pdf
Date

Sony STR-DN1010 Service Manual ▷ View online

STR-DN1010
61
DIGITAL  VIDEO  BOARD  (5/5)  IC3000  R5F3640DDFBR-128 (HDMI  CONTROLLER)
Pin No.
Pin Name
I/O
Description
1 to 5
NC
O
Not used
6
BYTE
I
External data bus width selection signal input terminal    “L”: 16 bit    Fixed at “L” in this set
7
CNVSS
I
Processor mode selection signal input terminal    “L”: single chip mode    
Fixed at “L” in this set
8, 9
NC
O
Not used
10
RESET
I
Reset signal input from the system controller    “L”: reset
11
XOUT
O
System clock output terminal (10 MHz)
12
VSS
-
Ground terminal
13
XIN
I
System clock input terminal (10 MHz)
14
VCC_3.3V
-
Power supply terminal (+3.3V)
15
NMI
I
Non-maskable interrupt signal input terminal    Not used
16 to 18
NC
O
Not used
19
RX_RST
O
Reset signal output to the HDMI receiver    “L”: reset
20
RX_INT
I
Interrupt signal input from the HDMI receiver
21
1444_HPD
O
Hot plug detection control signal output to the HDMI input selector
22
HPD_IN1
O
Hot plug detection control signal output to the HDMI IN 1 connector
23 to 26
NC
O
Not used
27
CSCL
O
I2C clock signal output to the EEPROM, HDMI receiver and HDMI transmitter
28
CSDA
I/O
I2C data bus with the EEPROM, HDMI receiver and HDMI transmitter
29
232COUT (VU TX)
O
Serial data output to the connector (for RS-232C) and DSP
30
232CIN (VU RX)
I
Serial data input from the connector (for RS-232C) and DSP
31
CLK 1
O
Not used
32
RTS 1
O
Not used
33
VUCOM_SDA
I/O
I2C data bus with the system controller
34
VUCOM_SCL
I
I2C clock signal input from the system controller
35
EDID_SELA
O
Write protect signal output to the EEPROM
36
EDID_SELB
O
Input data selection signal output to the data selector
37 to 39
NC
O
Not used
40
VDAC_RESET
O
Not used
41
TX_5VPWR
O
Power supply on/off control signal output terminal for HDMI OUT connector    “H”: power on
42
TX_RST
O
Reset signal output to the HDMI transmitter    “L”: reset
43
TX_INT
I
Interrupt signal input from the HDMI transmitter
44 to 50
NC
O
Not used
51 to 53
1444_SELA to 
1444_SELC
O
HDMI input selection signal output to the HDMI input selector
54
1444_OEB
O
Output enable signal output to the HDMI input selector
55, 56
P5V_SELA, P5V_SELB
O
HDMI +5V power input selection signal output terminal
57 to 59
NC
O
Not used
60
VCC_3.3V
-
Power supply terminal (+3.3V)
61
NC
O
Not used
62
VSS
-
Ground terminal
63
NC
O
Not used
64
NON LPCM
O
Non-LPCM setting signal output to the DSP    “L”: LPCM
65
MUTE
O
Error signal output to the system controller and DSP
66 to 90
NC
O
Not used
91 to 93
MODEL_SW3 to 
MODEL_SW1
I
Model setting terminal
94
AVSS
-
Ground terminal
95
NC
O
Not used
96
VREF
I
Reference voltage (+3.3V) input terminal
97
AVCC
-
Power supply terminal (+3.3V)
98 to 100
NC
O
Not used
STR-DN1010
62
DIGITAL  VIDEO  BOARD  (3/5)  IC3201  FLI30502AC (VIDEO  CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
VDDA33_LBADC
-
Power supply terminal (+3.3V)
2
LBADC_IN1
I
Standby signal input from the system controller
3 to 6
LBADC_IN2 to 
LBADC_IN5
-
Not used
7
VDDA33_LBADC
-
Power supply terminal (+3.3V)
8
RESETn
I
Reset signal input from the system controller
9
VBUFC_RPLL
-
Not used
10
VDD_RPLL_18
-
Power supply terminal (+1.8V)
11
GND_RPLL
-
Ground terminal
12
XTAL
O
System clock output terminal (19.6 MHz)
13
TCLK
I
System clock input terminal (19.6 MHz)
14
AVDD_RPLL_33
-
Power supply terminal (+3.3V)
15
VSYNC1_VGA
-
Not used
16
HSYNC1_VGA
-
Not used
17
STI_TM2
-
Not used
18
GPIO15/STI_TM1/
EXT_CSn
-
Not used
19
SCART16
-
Not used
20
CVDD_18
-
Power supply terminal (+3.3V)
21
CRVSS
-
Ground terminal
22
HOST_SCLK/
UART_DI/JTAG_CLK
O
Serial data input from the connector (for RS-232C) and DSP
23
HOST_SDATA/
UART_DO/
JTAG_MODE
I
Serial data output to the connector (for RS-232C) and DSP
24
DDC_SCLK
-
Not used
25
DDC_SDATA
-
Not used
26
CVDD_18
-
Power supply terminal (+1.8V)
27
CRVSS
-
Ground terminal
28
MSTR_SCLK
O
Clock signal output to the EEPROM
29
MSTR_SDATA
I/O
Two-way serial data with the EEPROM
30
RVDD_33
-
Power supply terminal (+3.3V)
31
CRVSS
-
Ground terminal
32 to 35
GPIO0 to GPIO3
-
Not used
36
GPIO6/IRin
Not used
37
CVDD_18
-
Power supply terminal (+1.8V)
38
CRVSS
-
Ground terminal
39
GPIO7/IRQin
-
Not used
40
GPIO8/IRQout
-
Not used
41
GPIO9/SIPC_SCLK/
A19
I
I2C data input from the system controller
42
GPIO10/
SIPC_SDATA/A20
I
I2C clock signal input from the system controller
43
CVDD_18
-
Power supply terminal (+1.8V)
44
CRVSS
-
Ground terminal
45, 46
GPIO11/PWM0, 
GPIO12/PWM1
-
Not used
47
RVDD_33
-
Power supply terminal (+3.3V)
48
CRVSS
-
Ground terminal
49
GPIO13/PWM2/
JTAG_RESET
-
Not used
50
GPIO14/PWM3/
SCART16_1
-
Not used
51
CVDD_18
-
Power supply terminal (+1.8V)
52
CRVSS
-
Ground terminal
53
GPIO4/VIDIN_HS
-
Not used
54
GPIO5/VIDIN_VS
-
Not used
55
VID2_CLK/ROM_OEn
-
Not used
56
VID_DE_FLD/A0/
GPIO16
-
Not used
STR-DN1010
63
Pin No.
Pin Name
I/O
Description
57
I2S_SPDIF_IN_DATA
-
Not used
58
I2S_IN_WCLK/
GPIO50
-
Not used
59
I2S_IN_BCLK/
GPIO51
-
Not used
60
I2S0_SPDIF_OUT_
DATA
-
Not used
61
I2S_OUT_WCLK/
GPIO52
-
Not used
62
I2S_OUT_BCLK/
GPIO53
-
Not used
63
I2S1_OUT_DATA
-
Not used
64
AUD_CLKOUT
-
Not used
65
CVDD_18
-
Power supply terminal (+1.8V)
66
CRVSS
-
Ground terminal
67
DEN/VOP_FLD
O
Data enable signal output to the HDMI transmitter and D/A converter
68
DHS/VOP_HS
O
Horizontal sync signal output to the HDMI transmitter and D/A converter
69
DHS/VOP_VS
O
Vertical sync signal output to the HDMI transmitter and D/A converter
70
DCLK/VOP_CLK
O
Output data clock signal output to the HSYNC select, HDMI transmitter and D/A converter
71
PBIAS
-
Not used
72
PPWR
-
Not used
73
AVSS_LV
-
Ground terminal
74
AVDD_LV_33
-
Power supply terminal (+3.3V)
75 to 84
CH3P_LV_E/R0, 
CH3N_LV_E/R1, 
CHKP_LV_E/R2, 
CHKN_LV_E/R3, 
CH2P_LV_E/R4, 
CH2N_LV_E/R5, 
CH1P_LV_E/R6, 
CH1N_LV_E/R7, 
CH0P_LV_E/G0, 
CH0N_LV_E/G1 
O
Serial data output to the HDMI transmitter and D/A converter
85
AVSS_OUT_LV
-
Ground terminal
86
AVDD_OUT_LV_33
-
Power supply terminal (+3.3V)
87 to 96
CH3P_LV_O/G2, 
CH3NLV_O/G3, 
CHKP_LV_O/G4, 
CHKN_LV_O/G5, 
CH2P_LV_O/G6, 
CH2N_LV_O/G7, 
CH1P_LV_O/B0, 
CH1N_LV_O/B1, 
CH0P_LV_O/B2, 
CH0N_LV_O/B3
O
Serial data output to the HDMI transmitter and D/A converter
97
AVSS_OUT_LV
-
Ground terminal
98
AVDD_OUT_LV_33
-
Power supply terminal (+3.3V)
99 to 102
PD20/B4/GPIO45 to 
PD23/B7/GPIO48
O
Serial data output to the HDMI transmitter and D/A converter
103
CVDD_18
-
Power supply terminal (+1.8V)
104
CRVSS
-
Ground terminal
105
GPIO49/A18
-
Not used
106
ROM_SCSn/
ROM_CSn
O
Serial data input from the serial fl ash
107
ROM_SCLK/A17
O
Serial clock signal output to the serial fl ash
108
ROM_SDO/A16/
OPM2
O
Serial data output to the serial fl ash
109
ROM_SDI/ROM_WEn
I
Serial data output to the serial fl ash
110
RVDD_33
-
Power supply terminal (+3.3V)
111
CRVSS
-
Ground terminal
112
EXT_ADC_CLAMP/
A15/OPM1
-
Not used
113
XOSD_CLK/A14/
OPM0
-
Not used
114
XOSD_HS/A13/FS1
-
Not used
STR-DN1010
64
Pin No.
Pin Name
I/O
Description
115
XOSD_VS/A12/FS0
-
Not used
116
XOSD_FLD/A11/FT1
-
Not used
117
VBI_DATA_7/A10/FT0
-
Not used
118, 119
VBI_DATA_6/A9/BT2, 
VBI_DATA_5/A8/BT1
-
Not used
120
VBI_DATA_4/A7/
GPO23/BT0
-
Not used
121
VBI_DATA_3/A6/
GPO22/OSC_SEL
-
Not used
122 to 
124
VBI_DATA_2/A5/
GPIO21 to 
VBI_DATA_0/A3/
GPIO19
-
Not used
125
VBI_VALID/A2/
GPIO18
-
Not used
126
VBI_CLK/A1/GPIO17
-
Not used
127
VID_DATA_IN_16/D0/
VID2_0
-
Not used
128
RVDD_33
-
Power supply terminal (+3.3V)
129
CRVSS
-
Ground terminal
130
VID_DATA_IN_17/D1/
VID2_1
-
Not used
131
CVDD_18
-
Power supply terminal (+1.8V)
132
CRVSS
-
Ground terminal
133
VID_DATA_IN_18/D2/
VID2_2
-
Not used
134
CVDD_18
-
Power supply terminal (+1.8V)
135
CRVSS
-
Ground terminal
136 to 
140
VID_DATA_IN_19/
D3/VID2_3 to 
VID_DATA_IN_23/D7/
VID2_7
-
Not used
141, 142
VID_DATA_IN_0, 
VID_DATA_IN_1
-
Not used
143
CVDD_18
-
Power supply terminal (+1.8V)
144
CRVSS
-
Ground terminal
145 to 
150
VID_DATA_IN_2 to 
VID_DATA_IN_7
-
Not used
151
VID_CLK1
-
Not used
152
RVDD_33
-
Power supply terminal (+3.3V)
153
CRVSS
-
Ground terminal
154
GPIO36/JTAG_TDO
-
Not used
155
GPIO35/JTAG_TDI
-
Not used
156
GPIO34
I
External receipt bus open signal input from the system controller
157
GPIO33
-
Not used
158
CVDD_18
-
Power supply terminal (+1.8V)
159
CRVSS
-
Ground terminal
160, 161
GPIO24, GPIO25
-
Not used
162, 163
VID_DATA_IN_8/
GPIO54, 
VID_DATA_IN_9/
GPIO55
-
Not used
164
GPIO26
-
Not used
165, 166
VID_DATA_IN_10, 
VID_DATA_IN_11
-
Not used
167 to 
169
GPIO27 to GPIO29
-
Not used
170, 171
VID_DATA_IN_12, 
VID_DATA_IN_13
-
Not used
172
RVDD_33
-
Power supply terminal (+3.3V)
173, 174
VID_DATA_IN_14, 
VID_DATA_IN_15
-
Not used
175
RVSS
-
Not used
Page of 102
Display

Click on the first or last page to see other STR-DN1010 service manuals if exist.