Sony STR-DH130 Service Manual ▷ View online
STR-DH130
5
1-2. BACK PANEL SECTION
1-3. FRONT PANEL SECTION
5 seven screws
(+BVTP 3x8)
(+BVTP 3x8)
4 two screws
(+BVTP 3x8)
(+BVTP 3x8)
3 three screws
(+BVTP 3x8)
(+BVTP 3x8)
2
wire (flat type) (9 core)
(CNS402)
1
CNP901 (3P)
3 five screws
(+BVTP 3x8)
(+BVTP 3x8)
4 claw
2
wire (flat type) (15 core)
(CNS600)
5
front panel section
1
CNP790 (4P)
STR-DH130
6
1-4. MAIN BOARD SECTION
6 two screws
(+BVTP 3x8)
(+BVTP 3x8)
7
MAIN board section
5 two screws
(+BVTP 3x8)
(+BVTP 3x8)
4 one screws
(+BVTP 3x8)
(+BVTP 3x8)
2
CNP911 (5P)
3
CNP930 (5P)
1
CNP902 (2P)
STR-DH130
7
SECTION 2
TEST MODE
[AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE]
(US, Canadian model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM
(US, Canadian model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
1. While pressing the [TUNING MODE] button, press the
1. While pressing the [TUNING MODE] button, press the
[
?/1
] button to turn on the main power.
2. The message “9K STEP” or “10K STEP” appears for a
moment
moment
and the channel step is changed.
[SOFTWARE VERSION DISPLAY MODE]
* The software version is displayed.
* Procedure:
1. While pressing the [SPEAKERS (OFF/A/B/A+B)] and the
[MUTING] buttons simultaneously, press the [
* The software version is displayed.
* Procedure:
1. While pressing the [SPEAKERS (OFF/A/B/A+B)] and the
[MUTING] buttons simultaneously, press the [
?/1
] button to
turn on the main power.
2. The destination and the software version are displayed.
2. The destination and the software version are displayed.
Destination
D1
D2
D3
VERSION
UNKNOWN
U
N
K
U2
U
2
1.
0
5
A
CA2
C
A
2
2.
0
5
A
CEL
C
E
L
3.
0
5
A
[KEY CHECK MODE]
* Button check
* Procedure:
1. While pressing the [SPEAKERS (OFF/A/B/A+B)] and the
* Button check
* Procedure:
1. While pressing the [SPEAKERS (OFF/A/B/A+B)] and the
[DIMMER] buttons simultaneously, press the [
?/1
] button to
turn on the main power.
2. The message “REST 13” appears.
3. Every press of any button other than the [
3. Every press of any button other than the [
?/1
] counts down
the buttons. The buttons which are already counted once are
not counted again. When all buttons are pressed “REST 00”
appears.
[VACUUM FLUORESCENT DISPLAY TEST MODE]
* All fl uorescent segments are tested. When this test is activated,
* All fl uorescent segments are tested. When this test is activated,
all segments light on at the same time, then each segment lights
on one after another.
on one after another.
* Procedure:
While pressing the [SPEAKER (OFF/A/B/A+B)] and the
While pressing the [SPEAKER (OFF/A/B/A+B)] and the
[DISPLAY] buttons simultaneously, press the [
?/1
] button to
turn on the main power.
1. ALL segments light on.
2. Turn the [INPUT SELECTOR] control, confi rm display.
3. Turn the [INPUT SELECTOR] control, confi rm display.
4. Turn the [INPUT SELECTOR] control, all segments light off.
[HISTORY MODE]
* The state that the set is used is memorized.
* Procedure:
1. While pressing the [TREBLE +] and [SPEAKERS (OFF/A/
* The state that the set is used is memorized.
* Procedure:
1. While pressing the [TREBLE +] and [SPEAKERS (OFF/A/
B/A+B)] buttons, press the [
?/1
] button to turn on the power
and “HISTORY” is displayed.
2. Each time the []/[] buttons on the remote commander is
pressed, the item is switched in order as follows.
Item
Display
History HISTORY
Count how many time of
protector happen
COUNT xx
Total single power on time
xxxxxHxx01
Input function
FUNCTION
HP ON/OFF
HP xxx
Volume
VOL xxx
Bass BASS
xxx
Treble TREB
xxx
Balance
F xxx
Total power on time
xxxxxHxx02
Muting MUTE
xxx
Power on counter
(Rebox Test Mode)
REBXxxxx
Protector Type
PROTxxxx
VACS step
VACS xx
Return to history
HISTORY
[PROTECTOR AUTO OFF]
* To disable auto off after protector occur
* Procedure:
1. While pressing the [TREBLE -] and [SPEAKERS (OFF/A/B/
* To disable auto off after protector occur
* Procedure:
1. While pressing the [TREBLE -] and [SPEAKERS (OFF/A/B/
A+B)] buttons, press the [
?/1
] button to turn on the main
power.
2. “PROT OFF” appears and switch off the set.
2. “PROT OFF” appears and switch off the set.
[SHIPMENT MODE]
* All preset contents are reset to the default setting.
* Procedure:
1. While pressing the [TUNING MODE] and the [MUTING]
* All preset contents are reset to the default setting.
* Procedure:
1. While pressing the [TUNING MODE] and the [MUTING]
buttons simultaneously, press the [
?/1
] button to turn on the
main
power.
2. “CLEARING” and “CLEARED” appear and switch off the
set.
set.
L
R
S
LFE
NEO:6
COAX S-AIR
-ES
x
PL
ZONE 2
EX
ST
SAT
k
ft.
MHz
MEMORY
SP B
C
SW
SL
SR
SBL SB SBR
SP A
DTS
II
RDS
CAT
96/24
MONO SLEEP
D
D.RANGE
OPT
dB
Hz
m
HDMI
L
R
S
LFE
NEO:6
COAX S-AIR
-ES
x
PL
ZONE 2
EX
ST
SAT
k
ft.
MHz
MEMORY
SP B
SW
SL
SR
SBL SB SBR
SP A
DTS
II
RDS
CAT
96/24
MONO SLEEP
D
D.RANGE
OPT
dB
Hz
m
C
HDMI
STR-DH130
8
[DESTINATION WRITE MODE]
* Write the set destination when the destination is “UNKNOWN”.
This mode can be performed once only.
* Procedure:
1. Press the [
* Write the set destination when the destination is “UNKNOWN”.
This mode can be performed once only.
* Procedure:
1. Press the [
?/1
] button to turn on the main power.
2. Press the [FM MODE] and [DISPLAY] buttons
simultaneously.
3. “DEST XXX” appears and turns [INPUT SELECTOR] to
select the required destination.
simultaneously.
3. “DEST XXX” appears and turns [INPUT SELECTOR] to
select the required destination.
Selection
Destination
DEST U2
U.S.A
DEST CEL
Europe
DEST CA2
CANADA
4. Press [MEMORY/ENTER] button to save the destination.
5. “CLEARING” and “CLEARED” appear and the set will
switch on.
6. Perform [SOFTWARE VERSION DISPLAY MODE] to
confi rm the written destination.
5. “CLEARING” and “CLEARED” appear and the set will
switch on.
6. Perform [SOFTWARE VERSION DISPLAY MODE] to
confi rm the written destination.
Click on the first or last page to see other STR-DH130 service manuals if exist.