Sony STR-DE235 Service Manual ▷ View online
– 35 –
IC950
NJM2103D
1
2
3
4
5
6
7
8
V+
VSB/SESIN
VSA
RESET
GND
OUTC
VSC
CR
VREF
+
–
–
+
–
+
–
+
Q
R
S
– DISPLAY Board –
IC202
BA6208
1
2
3
4
5
6
7
8
9
NC
OUTPUT 2
Vcc
GND
NC
INPUT 2
INPUT 1
NC
MOTOR
DRIVE
MOTOR
DRIVE
REG
SWITCH
SWITCH
OUTPUT1
– 36 –
4-15.
IC PIN FUNCTION DESCRIPTION
•
DISPLAY BOARD IC201
µ
PD78045FGF-082-3B9 (SYSTEM CONTROLLER, FL DRIVER)
Pin No.
Pin Name
I/O
Description
1 to 7
DIG7 to DIG1
O
Digit drive signal output to the fluorescent indicator tube (FL201)
8
VDD
—
Power supply terminal (+5V)
9
S.CLK
O
Serial data transfer clock signal output to the dolby surround pro-logic circuit (IC300, 301),
LC78212 (IC401) and PLL IC on FM/AM tuner pack “L” active
LC78212 (IC401) and PLL IC on FM/AM tuner pack “L” active
10
S.DATA
O
Serial data output to the dolby surround pro-logic circuit (IC300, 301), LC78212 (IC401) and
PLL IC on FM/AM tuner pack “L” active
PLL IC on FM/AM tuner pack “L” active
11
PLL.DATA
I
Serial data input from the PLL IC on FM/AM tuner pack “L” active
12
S.CE (LC7822)
O
Serial chip enable signal output to the LC78212 (IC401), PLL IC on FM/AM tuner pack
“H” active
“H” active
13
S.CE (LV1018)
O
Serial chip enable signal output to the dolby surround pro-logic circuit (IC300, 301)
“L” active
“L” active
14
REAR-RLY
O
Speaker protect relay drive signal output for the rear side speaker “H”: relay on
Not used (open)
Not used (open)
15
BRIDGE-RLY
O
Bridgeable relay drive signal output terminal “H”: relay on
16
PROTECT
I
Over load detect signal input from the protect circuit “L”: protect detect
17
RESET
I
System reset signal input from the reset signal generator (IC950, Q201) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
18
AUTO-STOP
I
Tuned display detection signal input from the FM/AM tuner pack “L”: tuned
19
STEREO-IN
I
Stereo detection signal input from the FM/AM tuner pack “L”: stereo
20
AVSS
—
Ground terminal (for A/D converter analog system)
21
SP-RLY
O
Speaker protect relay drive signal output for the front side speaker “H”: relay on
22
SURR-RLY
O
Speaker protect relay drive signal output for the surround speaker “H”: relay on
23
POWER-RLY
O
Relay drive signal output for the power on/off control “H”: relay on
24
SIGNAL
I
FM and AM signal meter voltage detection signal input from the FM/AM tuner pack
25
A/D-4
I
Key input terminal (A/D input) S234 to S244 (SET UP, NAME, ENTER, +, –, EFFECT/
DELAY, CENTER, REAR, MODE +, SOUND FIELD ON/OFF, MODE –) keys input
DELAY, CENTER, REAR, MODE +, SOUND FIELD ON/OFF, MODE –) keys input
26
A/D-3
I
Key input terminal (A/D input) S222 to S226, S220, S229 to S231 (BASS BOOST, MUTING,
SHIFT, 0, MEMORY, CD, MD/TAPE, TV/LD, RDS PTY) keys input
SHIFT, 0, MEMORY, CD, MD/TAPE, TV/LD, RDS PTY) keys input
27
A/D-2
I
Key input terminal (A/D input) S211 to S219, S227 (FM/AM, 6, 5, 4, 7, 8, 9, FM MODE,
VIDEO, TUNER) keys input
VIDEO, TUNER) keys input
28
A/D-1
I
Key input terminal (A/D input) S201 to S210 (DISPLAY, RDS EON, 3, 2, 1, TUNING –/+,
PRESET/PTY SELECT –/+, DIRECT) keys input
PRESET/PTY SELECT –/+, DIRECT) keys input
29
AVDD
—
Power supply terminal (+5V) (for A/D converter analog system)
30
AVREF
I
Reference voltage (+5V) input terminal (for A/D converter)
31
RDS DATA IN
I
RDS data input from the RDS decoder (IC1)
32
OPEN
—
Not used (open)
33
GND
—
Ground terminal
34
X1
I
Main system clock input terminal (4.19 MHz)
35
X2
O
Main system clock output terminal (4.19 MHz)
36
WOOFER-RLY
O
Relay drive signal output for the woofer speaker “H”: relay on Not used (open)
37
LED SELECT
O
LED select signal output terminal “H” active
38
PROLOGIC LED
O
LED drive signal output terminal “H”: LED on Not used (open)
39
C.STUDIO LED
O
LED drive signal output of the CINEMA (D231) indicator “H”: LED on
40
HALL LED
O
LED drive signal output of the MUSIC (D232) indicator “H”: LED on
41
ENTER LED
I
Not used (fixed at “L”)
42
VOL DOWN
O
Motor drive signal (volume down direction) output to the volume motor drive (IC202)
“H” active
“H” active
– 37 –
Pin No.
Pin Name
I/O
Description
43
VOL UP
O
Motor drive signal (volume up direction) output to the volume motor drive (IC202)
“H” active
“H” active
44
SYS-POWER
I
Power on/off switch (S200 I/
u) input terminal “L” is input when key pressing
45
TUNER-MUTE
O
Muting control signal output to the FM/AM tuner pack “H”: muting on
46
RDS CLK IN
I
RDS serial clock signal input from the RDS decoder (IC1)
47
STOP
I
Power down detection signal input from the reset signal generator (IC950)
“L”: power down, normally: “H”
“L”: power down, normally: “H”
48
VSS
—
Ground terminal
49
SIRCS
I
Sircs remote control signal input from the remote control receiver (IC203)
50
MUTING LED
O
LED drive signal output of the MUTING indicator (D240) “L”: LED on
51
5.1CH LED
O
LED drive signal output terminal “L”: LED on Not used
52
VDD
—
Power supply terminal (+5V)
53
BASS BOOST
O
Control signal output of the BASS BOOST circuit and LED drive signal output of the BASS
BOOST indicator (D228) “H”: BASS BOOST on (LED on)
BOOST indicator (D228) “H”: BASS BOOST on (LED on)
54
FUNC. MUTE
O
Audio line muting on/off control signal output terminal “H”: muting on
55
IC. MUTE
O
Muting on/off control signal output terminal “H”: muting on Not used (open)
56
VERSION
I
Setting terminal for the version
57
S2
O
Video input select signal output terminal Not used (pull down)
58
S1
O
Video input select signal output terminal Not used (pull down)
59
LED1
O
LED drive signal output of the CENTER (D233) and REAR (D237) indicators “H”: LED on
60
LED2
O
LED drive signal output of the NAME (D235) and EFFECT/DELAY (D236) indicators
“H”: LED on
“H”: LED on
61
LED3
O
LED drive signal output of the SET UP (D234) indicator “H”: LED on
62 to 70
S15 to S7
O
Segment drive signal output to the fluorescent indicator tube (FL201)
71
VLOAD
—
Negative power supply terminal for the fluorescent indicator tube drive (–24V)
72 to 77
S6 to S1
O
Segment drive signal output to the fluorescent indicator tube (FL201)
78 to 80
DIG10 to DIG8
O
Digit drive signal output to the fluorescent indicator tube (FL201)
– 38 –
(1)
CASE SECTION
SECTION 5
EXPLODED VIEWS
The components identified by
mark
mark
! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
specified.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
X-4947-207-1 FOOT ASSY (F50150S)
2
4-210-291-01 SCREW (CASE 3 TP2)
* 3
4-998-206-21 CASE (413226)
2
1
2
2
3
not
supplied
supplied
Front panel
section
section
not
supplied
supplied
#1
#1
#1
#1
not
supplied
supplied
1
not
supplied
supplied
Chassis section
Click on the first or last page to see other STR-DE235 service manuals if exist.