Sony STR-DA5500ES Service Manual ▷ View online
STR-DA5500ES
13
2-7. A-VIDEO BOARD
3 two screws
(BV3
u 8 CU)
2 eight screws
(BVTP3
u 8)
4 screw
(BVTP3
u 8)
6 screw
(BVTP3
u 8)
7 bracket (WB)
8 A-VIDEO board
1 three connectors
(CN6003, CN6008, CN6009)
5
2-8. A-AUDIO BOARD
3 screw
(B3
u 8)
3 seven screws
(BVTP3
u 8)
4 screw
(BVTP3
u 8)
2 four connectors
(CN605,
CN606,
CN607,
CN608)
1 wire (flat type) (9core)
(CN604) (US, Canadian)
wire (flat type) (11core)
(CN603) (AEP, UK)
7 screw
(BVTP3
u 8)
8 bracket (side)
9 A-AUDIO board
5 reinforcement
(PWB)
6
(US, Canadian)
STR-DA5500ES
14
2-9. HEAT SINK BLOCK
1 connector
(CN1405)
2 two connectors
(CN1207,
CN1209)
4 two connectors
(CN1205,
CN1206)
6 seven screws
(BV3
u 8 CU)
3 CONNECTOR1 board
7 heat sink block
5 CONNECTOR2 board
2-10. FRONT PANEL BLOCK
(AEP, UK)
(AEP, UK)
7
qs two spacers (408)
3 two saranet cushions
5 screw
(BVTP3
u 8)
5 five screws
(BVTP3
u 8)
8 screw (BVTP3 u 8)
9 terminal
5 two screws
(BVTP3
u 8)
qd front panel block
6 Cut the binding band (taiton).
q; Cut the binding
band
(taiton).
4 clamp filter (ferrite core)
qa clamp filter (ferrite core)
qa two clamp filters
(ferrite
core)
1 clamp filter
(ferrite
core)
2 clamp filter
(ferrite
core)
1 sleeve ferrite clamp
(US, Canadian)
(US, Canadian)
(US, Canadian)
(US, Canadian)
(US, Canadian)
(AEP, UK)
Note: In reassembling, use new binding band (taiton)
to fasten the binding band (taiton) same as before.
(US, Canadian)
STR-DA5500ES
15
2-11. POWER TRANSFORMER (T1), E-VOL/MAIN BOARDS
qh four screws
(BVTP3
u 8)
qs lead wire with connector
(CN1001)
qf two lead wires
qk screw
(BVTP3
u 8)
qj three screws
(BV/ring)
qd Cut the
binding band (taiton).
qd Cut the
binding band (taiton).
qd Cut the
binding band (taiton).
6 two screws
(BVTP3
u 8)
w; screw
(BVTP3
u 8)
w; two screws
(BVTP3
u 8)
wa clamp (L35)
qg two accessory
screws
(J1499)
qa two fuses (T4AL/250V)
(F1403,
F1404)
J1499
8 screw
(BVTP3
u 8)
8 screw
(BVTP3
u 8)
ql reinforcement (MAIN)
q; E-VOL board
ws MAIN board
9 bracket
(SS)
9 bracket
(SS)
2 four copper washer
+BVTT
assy’s
3 label (TR-ES/L)
4 power
transformer
(T1)
(T1)
1 two connectors
(CN1404,
CN1408)
5 two connectors
(CN1208,
CN1209)
7 two connectors
(CN1203,
CN1204)
Note: In reassembling, use new binding band (taiton)
to fasten the binding band (taiton) same as before.
STR-DA5500ES
16
SECTION 3
TEST MODE
SWAP MODE
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [2CH/A. DIRECT] and [MEMORY/
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [2CH/A. DIRECT] and [MEMORY/
ENTER] buttons, press the [POWER] button to turn on the
main power.
main power.
2. The message “SWAP MODE !” appears (No change while dis-
played).
HISTORY MODE
The state that the set is used is memorized.
Procedure:
1. While pressing the [MUSIC] and [MEMORY/ENTER] but-
The state that the set is used is memorized.
Procedure:
1. While pressing the [MUSIC] and [MEMORY/ENTER] but-
tons, press the [POWER] button to turn on the power and
“HISTORY MODE” is displayed.
“HISTORY MODE” is displayed.
2. Each time the [
M
]/[
m
] buttons of the remote commander is
pressed, the item is switched in order as follows.
Items
Display
Number of protector is gener-
ated
ated
PRCT_COUNT: XXX
Total time until protector is
generated
generated
TTL_TIME: XXXXH XXM
Sound fi eld
XXXXXXXXXXXXXXXX
Input Selector
INPUT: XXXXXXXXXX
Input mode
INMODE: XXXXXXXXXXXX
Input mode under lock state
DSEL: XXXXXXXXXXXXXXX
Stream under input
STREAM: XXXXXXX
Channel information
CONFIG:XXXXXXX
State of headphone
HEAD PHONES: XXX
Volume
VOL:
XXXdB
EQ setting value
BASS: XXXdB
TREB: XXXdB
TREB: XXXdB
Level collection value
each channel
each channel
Lv FL/FR XXXX/XXXX
Lv SL/SR XXXX/XXXX
Lv CT/SW XXXX/XXXX
Lv BL/BR XXXX/XXXX
Lv SL/SR XXXX/XXXX
Lv CT/SW XXXX/XXXX
Lv BL/BR XXXX/XXXX
Total time of power on
TTL_P_ON: XXXXH XXM
DIGITAL MEDIA PORT TEST
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN6751) on the NETWORK board.
2. While pressing the [A.F.D.] and [HDMI IN] buttons, press the
[POWER] button to turn on the main power.
3. The message “DMPORT OK” appears on the fl uorescent indi-
cator tube and enter the digital media port test mode (Confi r-
mation of communication line).
mation of communication line).
When “NO DETECT”, “UART NG” and “UART TO” are dis-
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
Each time the [
>
] button on the remote commander is
pressed, the connect check and adaptor version check are
switched.
switched.
Press the [
.
] button on the remote commander, connected
confi rmation of the DMPORT check jig is done again.
4. To a pin-jack of the DMPORT check jig input information
relevant to audio signal (sine-wave 1.0 Vrms) and composite
video signal (white 100% 1.0 Vp-p, color bar, etc.).
video signal (white 100% 1.0 Vp-p, color bar, etc.).
5. Confi rm the output of speakers and monitor TV (Confi rmation
of analog signal).
6. To release from this mode, press the [
x
] button on the remote
commander.
color
pattern
generator
DMPORT
check jig
(Part No.
J-2501-309-A)
J001
AF
oscillator
set
TV
monitor
FL/FR
speaker
NETWORK board
CN6751
MAIN board
TM4002
A-VIDEO board
J6002
XM FACTORY TEST MODE
(US and Canadian models only)
Mode to confi rm operation of XM. Doing display of ID of XM
antenna and output of audio signal that XM antenna generates, it is
confi rmed that there are no problems in the communication of the
XM antenna and the transmission of the audio signal.
Procedure:
1. The XM antenna was connected, while pressing the [TUNING
(US and Canadian models only)
Mode to confi rm operation of XM. Doing display of ID of XM
antenna and output of audio signal that XM antenna generates, it is
confi rmed that there are no problems in the communication of the
XM antenna and the transmission of the audio signal.
Procedure:
1. The XM antenna was connected, while pressing the [TUNING
MODE] and [MOVIE] buttons, press the [POWER] button to
turn on the main power.
turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1
kHz L and 1 kHz R are switched.
kHz L and 1 kHz R are switched.
SIRIUS FACTORY TEST MODE
(US and Canadian models only)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
(US and Canadian models only)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
[TUNING MODE] and [A.F.D.] buttons, press the [POWER]
button to turn on the main power.
button to turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 kHz L/R, 10 Hz L/R, noise L,
noise R, muting are switched.
noise R, muting are switched.
Click on the first or last page to see other STR-DA5500ES service manuals if exist.