Sony STR-DA3500ES Service Manual ▷ View online
STR-DA3500ES
13
SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A.
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A.
DIRECT], [MUSIC], [MOVIE (HD-D.C.S.)] button in order, the message “SPECIALIZE” appears.
2. Press the [M] [m] button on the remote commander, the message “< SPECIAL>” appears.
3. Press the [,] button on the remote commander, the item is appears.
4. Each time the [M] [m] button on the remote commander is pressed, the item is switched in order as follows.
Some items can change the content. Display the cursor by pressing the [,] button on the remote commander, and changing the content
by pressing the [M] [m] button on the remote commander, and fi x the content by pressing the [<] button on the remote commander
when you want to change the content of the item.
5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE (HD-
D.C.S.)] button in order again, the message “OFF” appears.
Items
Display
Remark
Main micom version display
M.Ver X.XX
X.XX: System controller software version
Video micom version display
V.Ver X.XX
X.XX: Video micom software version
Farouja version display
F.Ver X.XX
X.XX: Farouja software version
CGROM micom version display
G.Ver X.XX
X.XX: CGROM controller software version
DSP serial fl ash version display
S.Ver X.XX
X.XX: Serial fl ash software version
FLI update
FLI UPDATE
When [,] button on the remote commander is pressed, the message “ON”
or “OFF” is appears
HDCP key read
HDCP KEY
When [,] button on the remote commander is pressed, the message “ON”
or “OFF” is appears
Model/Destination change
MODEL
When [,] button on the remote commander is pressed, the message “A35
** XX” is appears
**: Destination
XX: fx or at
**: Destination
XX: fx or at
Video Factroy
V. FACTORY
Menu mode to enter video calibration menu
If the [ENTER] button of the remote commander is pressed, entering the
menu, and operating two the following menu become possible
If the [ENTER] button of the remote commander is pressed, entering the
menu, and operating two the following menu become possible
Video calibration
(Video factory)
(Video factory)
V.CALIBRATION
START?
START?
Procedure:
1. “DVD” is selected by using [INPUT SELECTOR] jog.
2. Connect a color pattern generator to the COMPONENT VIDEO COMPO
1. “DVD” is selected by using [INPUT SELECTOR] jog.
2. Connect a color pattern generator to the COMPONENT VIDEO COMPO
2 IN jack (J6001) and DVD VIDEO IN jack (J6004) on the VIDEO board.
3. Input 100% color bars signal from the color pattern generator.
4. Menu that measures individual difference of hardness by automatic op-
4. Menu that measures individual difference of hardness by automatic op-
eration in pressing the [ENTER] button of the remote commander, and
corrects reference value.
corrects reference value.
In a measurement once, only one of NTSC/PAL/HD can be measured
Auto cal mic test
SP OUT
When [,] button on the remote commander is pressed, the message
“SOURCE” or “MIC” is appears
SOURCE: normal mode, MIC: mode that output audio from mic input
SOURCE: normal mode, MIC: mode that output audio from mic input
FL display fonts test
FL FONT
When [,] button on the remote commander is pressed, the message
“0X**=X” is appears
**: 20 to FF, X: character
**: 20 to FF, X: character
FL display test
All segments turn on
Each time [DISPLAY] button to change as follows
all on t test pattern 1 t test pattern 2 t all off t all on
all on t test pattern 1 t test pattern 2 t all off t all on
DSP halt
DSP HALT
When [,] button on the remote commander is pressed, the message “ON”
or “OFF” is appears
Dither
DITHER
When [,] button on the remote commander is pressed, the message
“AUTO”, “ON” or “OFF” is appears.
Please never change on service (must keep “AUTO”)
Please never change on service (must keep “AUTO”)
Super reset
RESET
Not used for the servicing
When EEPROM initialization is required, perform the “memory clearing
mode”
When EEPROM initialization is required, perform the “memory clearing
mode”
RAM watch menu
RAM WATCH
When [,] button on the remote commander is pressed, the message
“XXXXXXXXXX” is appears
XXXXXXXXXX: Various internal RAM (Switching with [M] [m] button on the
XXXXXXXXXX: Various internal RAM (Switching with [M] [m] button on the
remote commander)
EEPROM debug
EEPROM
When [,] button on the remote commander is pressed, the message “****
XX” is appears
****: EEPROM address, XX: EEPROM data
****: EEPROM address, XX: EEPROM data
Protector on/off
PROTECTOR
When [,] button on the remote commander is pressed, the message “ON”
or “OFF” is appears
Audio swap
SWAP MODE
When [,] button on the remote commander is pressed, the message
“XXXXXXXXXX” is appears
XXXXXXXXXX: audio swap mode
Switching with [M] [m] button on the remote commander
XXXXXXXXXX: audio swap mode
Switching with [M] [m] button on the remote commander
STR-DA3500ES
14
Items
Display
Remark
Volume value display (FL/FR)
L****RXXXX
****: Front L-ch volume value, XXXX: Front R-ch volume value (for design
evaluation)
evaluation)
Volume value display (SL/SR)
S****SXXXX
****: Surround L-ch volume value, XXXX: Surround R-ch volume value (for
design evaluation)
design evaluation)
Volume value display (CT/SW)
C****WXXXX
****: Center volume value, XXXX: Sub woofer volume value (for design
evaluation)
evaluation)
Volume value display
(SBL/SBR)
(SBL/SBR)
B****BXXXX
****: Surround back L-ch volume value, XXXX: Surround back R-ch volume
value (for design evaluation)
value (for design evaluation)
DAC mute information disclosure 1
U XXXXXXXX
Display of module information to demand muting in system controller (for
design evaluation)
design evaluation)
DAC mute information disclosure 2
L XXXXXXXX
Display of module information to demand muting in system controller (for
design evaluation)
design evaluation)
Volume display
VOL XXXX
XXXX: Volume
FL display duty change
DUTY
When [,] button on the remote commander is pressed, the message “XXX”
is appears
XXX: Duty value of FL display (1% to 100%) (for design evaluation)
XXX: Duty value of FL display (1% to 100%) (for design evaluation)
Language display
LANGUAGE
Not used for the servicing.
STR-DA3500ES
15
SECTION 4
ELECTRICAL ADJUSTMENTS
BIAS ALIGNMENT ADJUSTMENT
(AEP and UK models)
(AEP and UK models)
Note: After 10 minutes or more have passed since the power supply was
turned on, this adjustment is done.
Connection:
+
–
–
digital voltmeter
CN6102 pin
1, 4, 6
(CN6104 pin
1, 4, 6, 8)
CN6102 pin
3, 5, 7
(CN6104 pin
3, 5, 7, 9)
Procedure:
1. Connect a digital voltmeter to the CN6102 (CN6104).
2. Press the [POWER] button to turn on the main power.
3. Adjust the RV400 (RV470, RV500, RV570, RV600, RV670,
1. Connect a digital voltmeter to the CN6102 (CN6104).
2. Press the [POWER] button to turn on the main power.
3. Adjust the RV400 (RV470, RV500, RV570, RV600, RV670,
RV700) so that the digital voltmeter reading is 5 mV to 20 mV.
Adjustment and Connection Location:
RV500
(SUR-R)
RV700
(SBR)
RV570
(SUR-L)
RV470
(F-L)
RV400
(CENTER)
RV600
(F-R)
RV670
(SBL)
– MAIN Board (Conductor Side) –
– A-CLASS SUPPORT A Board
(Conductor Side) –
(Conductor Side) –
– A-CLASS SUPPORT B Board
(Conductor Side) –
(Conductor Side) –
1
9
CN6104
1
9
CN6102
VIDEO CALIBRATION ADJUSTMENT
Adjustment to decide the standard of the video input signal.
Adjustment to decide the standard of the video input signal.
Note: After replacing DIGITAL VIDEO board, or after “SUPER RESET”
of the special menu mode is executed, perform this adjustment.
1. Adjustment jig
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute
it by the Blu-ray Disc player that can output the component termi-
nal and the video terminal at the same time (Substitution model
name example: BDP-S350).
However, please do the following signal output confi rmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
The color pattern generator that can output 100% in NTSC/PAL/
HD color bar signal to the component and the composite at the
same time is necessary for the adjustment.
When there is no color pattern generator, it is possible to substitute
it by the Blu-ray Disc player that can output the component termi-
nal and the video terminal at the same time (Substitution model
name example: BDP-S350).
However, please do the following signal output confi rmation with
the oscilloscope beforehand when substituting it with the Blu-ray
Disc player.
1-1. Component signal
Checking Component Video Output Y
Checking Component Video Output Y
Signal
DVD standard disc color bars (100%)
Check point
COMPONENT VIDEO OUT (Y)
terminal (75
terminal (75
Ω terminated)
Specifi cation
1.00 ± 0.03 Vp-p
1.00
r 0.03 Vp-p
Checking Component Video Output B-Y
Signal
DVD standard disc color bars (100%)
Check point
COMPONENT VIDEO OUT (P
B
/C
B
)
terminal (75
Ω terminated)
Specifi cation
0.70 ± 0.03 Vp-p
0.70
r 0.03 Vp-p
Checking Component Video Output R-Y
Signal
DVD standard disc color bars (100%)
Check point
COMPONENT VIDEO OUT (P
R
/C
R
)
terminal (75
Ω terminated)
Specifi cation
0.70 ± 0.03 Vp-p
0.70
r 0.03 Vp-p
STR-DA3500ES
16
1-2. S Video signal
Checking S Video Output S-Y
Checking S Video Output S-Y
Signal
DVD standard disc color bars (100%)
Check point
S VIDEO OUT (S-Y) terminal
(75
(75
Ω terminated)
Specifi cation
1.00 ± 0.03 Vp-p
1.00
r 0.03 Vp-p
Checking S Video Output S-C
Signal
DVD standard disc color bars (100%)
Check point
S VIDEO OUT (S-C) terminal
(75
(75
Ω terminated)
Specifi cation
286 ± 30 mVp-p
286
r 30 mVp-p
1-3. Composite signal
Video level confi rmation
Video level confi rmation
Signal
DVD standard disc color bars (100%)
Check point
LINE OUT (VIDEO) terminal
(75
(75
Ω terminated)
Specifi cation
1.00 ± 0.03 Vp-p
1.00
r 0.03 Vp-p
2. Video calibration adjustment
2-1. Connection
2-1. Connection
color pattern
generator
or
Blu-ray
Disc player
set
VIDEO board
MONITOR VIDEO OUT jack
(J6004)
MONITOR VIDEO OUT jack
(J6004)
TV
monitor
VIDEO board
COMPONENT VIDEO ASSIGNABLE
(INPUT ONLY) COMPO 2 IN jack (J6001)
DVD VIDEO IN jack (J6004)
COMPONENT VIDEO ASSIGNABLE
(INPUT ONLY) COMPO 2 IN jack (J6001)
DVD VIDEO IN jack (J6004)
2-2. Procedure for color pattern generator
1. It connects of step 2-1, and the turn on the main power.
2. “DVD” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern generator.
4. Press the [POWER] button to turn off the main power.
5. While pressing the [2CH/A.DIRECT] and [SPEAKERS (OFF/
1. It connects of step 2-1, and the turn on the main power.
2. “DVD” is selected by using [INPUT SELECTOR] dial.
3. Input NTSC color bars signal from the color pattern generator.
4. Press the [POWER] button to turn off the main power.
5. While pressing the [2CH/A.DIRECT] and [SPEAKERS (OFF/
A/B/A+B)] buttons, press the [POWER] button to turn on the
main power. When correctly entering the test mode “V.CAL
COMPLETE N:P:H” is displayed (keeps pressing two buttons
until the message appears).
main power. When correctly entering the test mode “V.CAL
COMPLETE N:P:H” is displayed (keeps pressing two buttons
until the message appears).
6. The NTSC signal adjustment is begun when press the cross
(center of cursor) button of remote commander, and the dis-
play changes from “NTSC:MW -----” to “NTSC:MW OK C S
V E” little by little. Finally, the display returns to the display of
“V.CAL COMPLETE N:P:H”.
play changes from “NTSC:MW -----” to “NTSC:MW OK C S
V E” little by little. Finally, the display returns to the display of
“V.CAL COMPLETE N:P:H”.
7. Input PAL color bars signal from the color pattern generator.
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color pat-
8. Perform step 6 to 7 for the PAL signal adjustment.
9. Input HD color bars signal (720p or 1080i) from the color pat-
tern generator.
10. Perform step 6 to 7 for the HD signal adjustment.
11. The turn off the main power.
11. The turn off the main power.
Click on the first or last page to see other STR-DA3500ES service manuals if exist.