Sony STR-DA3500ES Service Manual ▷ View online
STR-DA3500ES
9
2-8. MICON BOARD, DIGITAL BOARD
2-9. ACLASS BOARD
Note: In reassembling, use new clamp to
fasten the clamp same as before.
3 six connectors
(CN2030, CN2031, CN2032,
CN2230, CN2231, CN2232)
5 two connectors
(CN2010,
CN2023)
7 four screws
(BVTP2.
6)
qa screw
(BVTP3
u 8)
4 MICON DIGITAL CONN board
1 Cut the clamp.
6 MICON
board
8 connector
(CN5001)
q; connector
(CN2208)
2 three connectors
(CN2015, CN2016, CN2017)
qs two connectors
(CN2217,
CN2218)
9 DSP board
qd DIGITAL board
1 two screws
(BVTP3
u 8)
3 two screws
(BVTP3
u 8)
6 screw (BVTP3 u 8)
6 screw (BVTP3 u 8)
5 connector
(CN1909)
7 four connectors
(CN411, CN511, CN611, CN711)
2 A-CLASS SUPPORT A board
4 A-CLASS SUPPORT B board
8 ACLASS board
(US, Canadian)
STR-DA3500ES
10
2-10. MAIN BLOCK
2-11. MAIN BOARD
Note: This illustration sees the MAIN board from pin jack side.
5 screw
(BVTT4
u 8)
7 two screws
(BVTP3
u 8)
8 two screws
(BVTP3
u 8)
8 two screws
(BVTP3
u 8)
6 bracket (video PWB)
3 connector
(CN1401)
4 connector
(CNP54)
2 two connectors
(CN811,
CN801)
9 main block
Note: In reassembling, use new clamp to
fasten the clamp same as before.
1 Cut the clamp.
1 Cut the clamp.
1 Cut the two clamps.
(US, Canadian)
2 two screws
(BVTP3
u 8)
1 Remove the forty-two solders.
4 MAIN board
3 heat sink block
STR-DA3500ES
11
SECTION 3
TEST MODE
TUNER AM STEP CHANGE MODE
(US and Canadian models)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [POWER] button to turn on the main power.
2. Turn the [INPUT SELECTOR] dial to select the “AM TUN-
(US and Canadian models)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [POWER] button to turn on the main power.
2. Turn the [INPUT SELECTOR] dial to select the “AM TUN-
ER”.
3. Press the [POWER] button to turn off the main power.
4. While pressing the [TUNING MODE] button, press the
4. While pressing the [TUNING MODE] button, press the
[POWER] button to turn on the main power.
5. Either the message “AM 9k Step” or “AM10k Step” appears,
select the desired step.
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [POWER] but-
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [POWER] but-
ton to turn on the main power.
2. The message “S.F. CLEAR” appears and initialization is per-
formed.
INITIALIZE MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TONE MODE] and [2CH/A.DIRECT]
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TONE MODE] and [2CH/A.DIRECT]
buttons, press the [POWER] button to turn on the main power.
2. The message “CLEARING” appears and the memories are re-
set to the default values.
3. When done, the message “CLEARED !” appears.
FLUORESCENT INDICATOR TUBE DISPLAY TEST
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [TONE MODE] and [A.F.D.] buttons,
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [TONE MODE] and [A.F.D.] buttons,
press the [POWER] button to turn on the main power.
2. All segments and all LEDs turn on.
SWAP MODE
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [MEMORY/ENTER] and [2CH/A.
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [MEMORY/ENTER] and [2CH/A.
DIRECT] buttons, press the [POWER] button to turn on the
main power.
main power.
2. The message “SWAP MODE” appears (No change while dis-
played).
SOUND FIELD LOCK ON/OFF CHANGE MODE
All buttons operation on/off of the front panel is changed.
Procedure:
1. While pressing the [SPEAKERS (OFF/A/B/A+B)] and
All buttons operation on/off of the front panel is changed.
Procedure:
1. While pressing the [SPEAKERS (OFF/A/B/A+B)] and
[MUSIC] buttons, press the [POWER] button to turn on the
main power.
main power.
2. Either the message “S.F. LOCK OFF” or “S.F. LOCK ON”
appears.
COMMAND MODE CHANGE MODE
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [2CH/A. DIRECT] button, press the
The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the [2CH/A. DIRECT] button, press the
[POWER] button to turn on the main power.
2. Either the message “C. MODE AV1” or “C. MODE AV2” ap-
pears. Select the desired mode.
XM FACTORY TEST MODE (US and Canadian models)
Mode to confi rm operation of XM. Doing display of ID of XM
antenna and output of audio signal that XM antenna generates, it is
confi rmed that there are no problems in the communication of the
XM antenna and the transmission of the audio signal.
Procedure:
1. The XM antenna was connected, while pressing the [TUNING
Mode to confi rm operation of XM. Doing display of ID of XM
antenna and output of audio signal that XM antenna generates, it is
confi rmed that there are no problems in the communication of the
XM antenna and the transmission of the audio signal.
Procedure:
1. The XM antenna was connected, while pressing the [TUNING
MODE] and [MOVIE] buttons, press the [POWER] button to
turn on the main power.
turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1
kHz L and 1 kHz R are switched.
kHz L and 1 kHz R are switched.
SIRIUS FACTORY TEST MODE
(US and Canadian models)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
(US and Canadian models)
Mode to confi rm operation of SIRIUS. Doing display of ID of
SIRIUS antenna and output of audio signal that SIRIUS antenna
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio
signal.
Procedure:
1. The SIRIUS antenna was connected, while pressing the
[TUNING MODE] and [A.F.D.] buttons, press the [POWER]
button to turn on the main power.
button to turn on the main power.
2. Whenever the [DISPLAY] button is pressed, the output of the
audio signal of 1 kHz L/R, 20 Hz L/R, 10 kHz L/R, noise L,
noise R and stop tone are switched.
noise R and stop tone are switched.
STR-DA3500ES
12
HISTORY MODE
The state that the set is used is memorized.
Procedure:
1. While pressing the [MEMORY/ENTER] and [MUSIC] but-
The state that the set is used is memorized.
Procedure:
1. While pressing the [MEMORY/ENTER] and [MUSIC] but-
tons, press the [POWER] button to turn on the power and
“HISTORY” is displayed.
“HISTORY” is displayed.
2. Each time the [M] [m] key of remote commander is pressed,
the item is switched in order as follows.
Items
Display
Protector count
COUNT XX
Total single power on time
SxxxxxHxxM
Sound fi eld
xxxxxxxxxx
Input function
xxxxxxxxxx
Input mode
xxxxxxxxxx
Digital select
xxxxxxxxxx
Stream information
xxxxxxxxxx
Signal confi guration
CONF xxxxx
Headphones
HEADPH xxx
Volume
VOL xxxxx
Bass
BASS xxxdB
Treble
TREB xxxdB
Level FL/FR
FL/R xxxxxx
Level SL/SR
SL/R xxxxxx
Level CT/SW
C/SW xxxxxx
Level BL/BR
BL/R xxxxxx
Total power on time
T xxHxxM
Muting
MUTING xxx
Power on counter
(Rebox test mode)
(Rebox test mode)
REBOX xxxx
DIGITAL MEDIA PORT TEST
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN8003) on the MICON board.
2. While pressing the [MEMORY/ENTER] and [A.F.D.] buttons,
press the [POWER] button to turn on the main power.
3. The message “DMPORT T.” and “DMPORT OK”appears on
the fl uorescent indicator tube and enter the digital media port
test mode (Confi rmation of communication line).
test mode (Confi rmation of communication line).
When “NO DETECT”, “UART NG” and “UART TO” are dis-
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.
Each time the [>] button on the remote commander is
pressed, the connect check and adaptor version check are
switched.
switched.
Press the [.] button on the remote commander, connected
confi rmation of the DMPORT check jig is done again.
confi rmation of the DMPORT check jig is done again.
4. To a pin-jack of the DMPORT check jig input information
relevant to audio signal (sine-wave 1.0 Vrms) and composite
video signal (white 100% 1.0 Vp-p, color bar, etc.).
video signal (white 100% 1.0 Vp-p, color bar, etc.).
5. Confi rm the output of speakers and monitor TV (Confi rmation
of analog signal).
6. To release from this mode, press the [x] button on the remote
commander.
color
pattern
generator
DMPORT
check jig
(Part No.
J-2501-309-A)
J001
AF
oscillator
set
TV
monitor
FL/FR
speaker
MICON board
CN8003
MAIN board
TM602
VIDEO board
J6004
SOFTWARE VERSION DISPLAY MODE
The software version is displayed.
Procedure:
1. While pressing the [TONE MODE] and [MUSIC] buttons,
The software version is displayed.
Procedure:
1. While pressing the [TONE MODE] and [MUSIC] buttons,
press the [POWER] button to turn on the main power.
2. The message “M.Ver X.XX” appears.
Each time the [DISPLAY] button is pressed, “H.Ver X.XX”,
“V.Ver X.XX”, “G.Ver X.XX”, “F.Ver X.XX” and “S.Ver
X.XX” this order, and returns to the “M.Ver X.XX” displayed.
“V.Ver X.XX”, “G.Ver X.XX”, “F.Ver X.XX” and “S.Ver
X.XX” this order, and returns to the “M.Ver X.XX” displayed.
REBOX TEST MODE
Procedure:
1. While pressing the [A.F.D] and [SPEAKERS (OFF/A/B/
Procedure:
1. While pressing the [A.F.D] and [SPEAKERS (OFF/A/B/
A+B)] buttons, press the [POWER] button to turn on the main
power.
power.
2. The message “REBOX-XXXX” appears.
KEY CHECK MODE
Button check
Procedure:
1. While pressing the [MEMORY/ENTER] and the [MOVIE
Button check
Procedure:
1. While pressing the [MEMORY/ENTER] and the [MOVIE
(HD-D.C.S.)] buttons, press the [POWER] button to turn on
the main power.
the main power.
2. Either the message “REST 11” appears.
Every pressing of any button other than the [POWER] counts
down the buttons. The buttons which are already counted once
are not counted again. When all buttons are pressed “REST
00” appears.
down the buttons. The buttons which are already counted once
are not counted again. When all buttons are pressed “REST
00” appears.
Click on the first or last page to see other STR-DA3500ES service manuals if exist.