DOWNLOAD Sony STR-DA3200ES / STR-DG1000 Service Manual ↓ Size: 18.84 MB | Pages: 127 in PDF or view online for FREE

25

1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH], [MUSIC],

[MOVIE] button in order.

2. The message “MENU SPECIALIZED!” appears.
3. Each time the 

M

  

m

 button of the remote commander is pressed, the item is switched in order as follows.

4. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH], [MUSIC], [MOVIE] button in order again.
5. The message “MENU SPECIALIZED OFF” appears.

Items

Protector on/off

Model version display

Model/destination change

XM TUNER version display

FM/AM tuner version display

HDMI controller version display

HDMI controller update mode

Auto cal mic test

FL display fonts test

FL display test

Audio swap

DSP halt

DSP RAM

DSP Version display

Volume value display (FL/FR)

Volume value display (SL/SR)

Volume value display (CT/SW)

Volume value display

(SBL/SBR)

DAC mute information disclosure

1

DAC mute information disclosure

2

EERROM debug

Super reset

2nd volume value display

FL display duty change

Display

PROTECTOR ON/OFF [XXX]

##### *** vX. XX @@@@

MODEL [##### * * * *] X X

XM Tuner Ver X. XX

FM/AM Tuner Ver X. XX

HDMI Micom Ver X. XX

HDMIUcom Update [XXX]

SPEAKER OUT [XXXXX]

FL FONT 0x ** = [X]

ALL ON

SWAP [XXXXXXXXXXX]

DSP HALT [XXX]

[*****]=XXXXXXXX

DSP Ver S: ***, P: XXX

FL**** FR XXXX

SL**** SR XXXX

CT**** SW XXXX

SBL**** SBR XXXX

DAC MUTE U XXXXXXXX

DAC MUTE L XXXXXXXX

EEPROM [****] FR XX

SUPER RESET [XXX]

2nd VOLUME XXX

DARK OUT DUTY [XXX%]

Remark

XXX: ON or OFF

(switching with  

M

  

m

  button of the remote commander)

#####: model

***: destination

X.XX: system controller software version

@@@@: Sum value of flash memory in the main system controller

#####: model, ****: destination, XX: at or fx

(switching with  

M

  

m

  button of the remote commander)

X.XX: XM tuner controller software version

X.XX: FM/AM tuner controller software version

X.XX: HDMI controller software version

XXX: ON or OFF (switching with  

M

  

m

  button of the remote commander)

Reset control form the system controller side and the reset control from the

PC side interfere mutually when updating the HDMI controller and it

becomes writing NG

Therefore, when this mode is set to ON, the reset control from the system

controller side is not done

XXXXX: Selection of speaker output audio

[SOURCE]: nomally mode, [MIC]: mode that output audio from mic from

speaker

**: 20 to FE, X: character (switching with  

M

  

m

  button of the remote

commander)

Each time DISPLAY button to change as follows.

all on 

→ test pattern 1 → test pattern 2 → all off → all on

Switching with  

M

  

m

  button of the remote commander

XXX: ON or OFF (switching with  

M

  

m

  button of the remote commander)

Mode not to send DSP host code, and to make only decipherment done

Mode that refers to internal RAM of DSP (for design evaluation)

***: DSP decoder patch version

XXX: DSP post process version

****: Front L-ch volume value

XXXX: Front R-ch volume value

****: Surround L-ch volume value

XXXX: Surround R-ch volume value

****: Center volume value

XXXX: Sub woofer R-ch volume value

****: Surround back L-ch volume value

XXXX: Surround  back R-ch volume value

Display of module information to demand muting in system controller (for

design evaluation)

Display of module information to demand muting in system controller (for

design evaluation)

****: EEPROM address

XX: EEPROM data (switching with  

M

  

m

  button of the remote commander)

Not used for the servicing

If super reset is performed, “up convert signal level adjustment” will also be

initialized

When EEPROM initialization is required, perform the “all clear mode”

XXX: 2nd room volume value (00 to 

∞)

XXX: Duty value of FL display (0% to 100%)

(switching with  

M

  

m

  button of the remote commander)

26

Display

YUV Y DRIVE [XX]

YUV U DRIVE [XX]

YUV V DRIVE [XX]

STOP CLK [XX] [XX] [XX]

Remark

XX: Gain control value of brighness (00 to 1F)

(switching with  

M

  

m

  button of the remote commander)

XX: Gain control value of color difference (Cb) (00 to 1F)

(switching with  

M

  

m

  button of the remote commander)

XX: Gain control value of color difference (Cr) (00 to 1F)

(switching with  

M

  

m

  button of the remote commander)

Value of register related to clock of system controller display mode (for

design evaluation)

Items

YUV Y  drive

YUV U drive

YUV V drive

Stop clock

27

Afer 10 minutes or more have passed since the power supply was
turned on, this adjustment is done.

1. Connect a digital voltmeter to the CNP1502 (CNP1552,

CNP1602, CNP1702, CNP1752, CNP1802, CNP1852) on the
BIAS board.

2. Press the [POWER] button to turn on the main power.
3. Adjust the RV1501 (RV1551, RV1601, RV1701, RV1751,

RV1801, RV1851) so that the digital voltmeter reading is 4 mV
to 20 mV.

+
–

digital voltmeter

CNP1502 (CNP1552, CNP1602, CNP1702, CNP1752, CNP1802, CNP1852) pin 

1

CNP1502 (CNP1552, CNP1602, CNP1702, CNP1752, CNP1802, CNP1852) pin 

2

CNP1752

RV1751

1

2

1

2

1

2

1

2

1

2

1

2

1

2

RV1701

CNP1702

RV1551

RV1501

RV1601

CNP1502

CNP1552

CNP1602

CNP1852

CNP1802

RV1851

RV1801

28

1. Connect a frequency counter to the TP6501 pin 2 on the VIDEO

board.

2. Press the [POWER] button to turn on the main power.
3. Perform the MEMORY CREARING MODE.
4. Press the [MENU] button on the remote commander to display

“Lebel Setting”.

5. Press the  

V

  

v

  button on the remote commander to display

“Video Settings” and press the 

  button on the remote

commander.

6. Press the  

V

  

v

  button on the remote commander to display

“COLOR SYSTEM” and press the 

 button on the remote

commander.

7. Press the 

  V

   

v

    button on the remote commander to select

NTSC.

8. Adjust the CT6501 (DA3200ES; US, Canadian, Taiwan/

DG1000) or CT6502 (DA3200ES; AEP, UK) so that the
frequency counter reading is 3.579545 MHz.

9. Press the 

  V

   

v

    button on the remote commander to select

PAL.

10. Adjust the CT6503 so that the frequency counter reading is

4.433618 MHz.

The Steps 9 and 10 should be performed to AEP and UK models of
DA3200ES.

VIDEO board

TP6501 pin 

2

+
–

frequency counter

CT6502

TP6501

1

4

CT6501

CT6503