DOWNLOAD Sony STR-DA1ES / STR-DB780 Service Manual ↓ Size: 7.8 MB | Pages: 84 in PDF or view online for FREE

9

1

wire (flat type) (9 core)
(CN201)

4

video.AU board

2

connector
(CN202)

3

two screws (BV/RING)

3

screw (BV/RING) 
(DB780: AEP, UK models)

1

wire (flat type) (31 core)
(CNS4)

2

four connectors
(CN1109, CNP5, CNP6, CNP9)

6

five screws
(BV/RING)

8

digital board

7

two connectors
(CN1102, CN1103)

4

bracket (digital 3)

5

screw
(BVTP3 

× 

8)

3

screw
(BVTP3 

× 

8)

3

screw
(BVTP3 

× 

8)

Note:When installing the digital board (CNS4), connecting the

wire (flat type) (31core) to the digital board beforehand
improves the operatability.

10

3

two screws
(BVTP3 

× 

8)

3

two screws
(BVTP3 

× 

8)

4

screw (BVTP3 

× 

8)

2

five screws 
(BV/RING)

1

three connectors
(CN801, CN803, CN805)

1

connector 
(CN902)

5

6

connector (CN809)

7

ten screws
(transistor)

6

five connectors
(CN631, CN431, CN481, CN531, CN581)

9

main board

8

heat sink

11

When this mode is used, the destination and the software version
number are displayed.
Procedure:
1. While pressing the 

[ENTER]

 and 

[AUTO DEC.]

 buttons, press

the 

/1

button to turn on the main power.

2. The destination and the software version number appear.

When this mode is used, the destination and the software version
number are displayed.
Procedure:
1. While pressing the 

[FM/AM]

 and 

[CINEMA STUDIO EX C]

buttons, press the 

/1

button to turn on the main power.

2. The message “REST 30” appears.
3. Every pressing of any button other than the 

/1

button counts

down the buttons. The buttons which are already counted once
are not counted again.

4. When all buttons are pressed, the message “REST 00” appears.

All preset contents are reset to the default setting.
Procedure:
1. While pressing the 

[DIMMER]

 and 

[SET UP]

 buttons, press

the 

/1

button to turn on the main power.

2. The message “FACTORY” appears and the present contents

are reset to the default values.

Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. While pressing the 

[PRESET TUNING +]

  or 

[TUNING +]

button, press the  

/1

button to turn on the main power.

2. Either the message “9 k STEP” or “10 k STEP” appears. Se-

lect the desired step.

Procedure:
1. While pressing the 

[MEMORY]

 button, press the  

/1

button

to turn on the main power.

2. The message “AUTO-BETICAL SELECT” appears and scans

and stores all the FM and FM RDS stations in the broadcast
area.

3. When done, the message “FINISH” appears.

The preset sound field is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the 

[MODE +]

 button, press the

/1

button to

turn on the main power.

2. The message “SF. CLR.” appears and initialization is

performed.

All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the 

[AUTO DEC.]

 and 

[MODE +]

 buttons, press

the 

/1

button or press the 

/1

button for more than five

seconds to turn on the main power.

2. The message “MEMORY CLEARED !” appears and the

memories are reset to the default values.

All fluorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the 

[DISPLAY]

 and 

[ENTER]

 buttons, press

the

/1

button to turn on the main power.

2. All segments and all LEDs turn on.
3. Turn the 

[FUNCTION]

 dial.

4. Half of segments and 

[Digital Cinema Sound]

, 

[AUTO DEC.]

,

[MODE]

 LEDs turn on.

5. Turn the 

[FUNCTION]

 dial once again.

6. Others half of segments and 

[2CH ST]

, 

[INPUT MODE]

,

[MULTI CH DIRECT]

 LEDs turn on.

7. Turn the 

[FUNCTION]

 dial once again.

8. All segments and all LEDs turn off.

12

Procedure:
1. While pressing the 

[2CH ST]

 and 

[CINEMA STUDIO EX C]

 buttons, press the 

/1

button to turn on the main power or press the

/1

button to turn on the main power, then press three buttons of 

[ENTER]

, 

[2CH ST]

 and 

[CINEMA STUDIO EX C]

 simultaneously.

2. The message “DSP TEST” appears, then change into “SWP. XXXX”.
3. Each time the 

[>]

 button is pressed, the item is switched in order as follows .

Items

Display

Remark

SWAP

SWP. XXXX

NORM, ALL, C SW, SLSR (switching with jog dial)

DSP communication

DSP OK or DSP ERROR

When DSP ERROR is displayed, press the 

[ENTER]

 key will clear

error

Bass management

BM. XXXX

AUTO, OFF, 1 to 15 (switching with jog dial)

Main speaker cut off frequency

MAIN XXX

80 Hz to 200 Hz (switching with jog dial by 10 Hz)

LFE cut off frequency

LFE XXX

80 Hz to 200 Hz (switching with jog dial by 10 Hz)

Co-ef. Read address

RA.12XXX

Turn the jog dial to switch the read data address

Co-ef. Read data

RD.XXXXXX xx

Value is read data

Co-ef. Write address

WA.12XXX

Turn the jog dial to switch the write data address

Co-ef. Write data

WD.XXXXXX xx

Turn the jog dial to set the write data

SRAM

RAMC XXXX

OFF, EXE, NG, PASS

Total operation time

TTL-XXXX xx

4 large character is hour, 2 small character is minutes

Longest power on time

LNG-XXXX XX

Volume 

I – 50 dB time display

V50-XXXX XX

Volume 

I – 40 dB time display

V40-XXXX XX

Volume 

I – 30 dB time display

V30-XXXX XX

Volume 

I – 20 dB time display

V20-XXXX XX

Volume 

I – 10 dB time display

V10-XXXX XX

Volume 

I 0 dB time display

V00-XXXX XX

Protector count value

PROT XXX

0 to 255

Fuse open count value

FUSE XXX

0 to 255

EEPROM condition

E-XXXXX

S RST (super reset, first time use EEPROM, test pattern corrupted)
FAIL (EEPROM read/write with microprocessor have problem)
V CHG (software version change)
D CHG (destination/model change)
CLEAR (back up data initialize)
NORM (normal AC on)

EEPROM read

E-XXX-XX

First four hex code is EEPROM address
Last two hex code is EEPROM data

EEPROM super reset

S.RST-YES or S.RST-NO

When S.RST-YES is displayed, press the 

[ENTER]

 key will clear all

EEPROM data