Sony STR-DA1200ES Service Manual ▷ View online
STR-DA1200ES
17
3-11. MAIN BOARD
3-10. POWER TRANSFORMER (T01)
4
connector
(CNP02)
(CNP02)
7
power transformer (T01)
5
two screws
(BVTT4
(BVTT4
×
8)
3
connector
(CNP1403)
(CNP1403)
6
two screws
(BVTT4
(BVTT4
×
8)
2
connector
(CNP1404)
(CNP1404)
1
connector
(CNP1451)
(CNP1451)
6
connector
(CN2021)
(CN2021)
5
connector
(CN2012)
(CN2012)
1
connector
(CN1410)
(CN1410)
2
connector
(CN1902)
(CN1902)
3
connector
(CNP54)
(CNP54)
4
connector
(CNP1001)
(CNP1001)
q;
MAIN board
9
two screws
(BVTP3
(BVTP3
×
8)
7
three screws
(BV/RING)
(BV/RING)
8
four screws
(BVTP3
(BVTP3
×
8)
18
STR-DA1200ES
SECTION 4
TEST MODE
TUNER FACTORY PRESET MODE
All preset contents are reset to the default setting.
Procedure:
Procedure:
1. While pressing the [2CH] and [TUNING MODE] buttons, press
the [POWER] button to turn on the main power.
2. The message “Factory Preset” appears and the present contents
are reset to the default values.
MEMORY CLEARING MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TONE MODE] and [MULTI CH IN] buttons,
press the [POWER] button to turn on the main power.
2. The message “MEMORY CLEARING...” appears and the
memories are reset to the default values.
3. When done, the message “MEMORY CLEARED !” appears.
SWAP MODE
Procedure:
1. While pressing the [2CH] and [MULTI CH IN] buttons, press
the [POWER] button to turn on the main power.
2. The message “SWAP MODE !” appears.
3. Press the [DISPLAY] button.
4. The message “
3. Press the [DISPLAY] button.
4. The message “
−
34.5 dB” appears. (Volume level is “MID”)
5. Press the [DISPLAY] button once again.
6. The message “23.0 dB” appears. (Volume level is “MAX”)
7. Press the [DISPLAY] button once again.
8. The message “
6. The message “23.0 dB” appears. (Volume level is “MAX”)
7. Press the [DISPLAY] button once again.
8. The message “
−∞
dB” appears. (Volume level is “MIN”)
FLUORESCENT INDICATOR TUBE PATTERN
CHECK MODE
CHECK MODE
All fluorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the [MOVIE] and [MULTI CH IN] buttons, press
the [POWER] button to turn on the main power.
2. All segments and all LEDs turn on.
SOUND FIELD CLEAR MODE
The preset sound field is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [POWER] button
to turn on the main power.
2. The message “S. F. Initialize” appears and initialization is
performed.
COMMAND MODE CHANGE MODE
The command mode of the remote-commander which this set
receives can be changed.
Procedure:
receives can be changed.
Procedure:
1. While pressing the [2CH] button, press the [POWER] button to
turn on the main power.
2. Either the message “COMMAND MODE [AV1]” or
“COMMAND MODE [AV2]” appears. Select the desired
mode.
mode.
SF LOCK ON/OFF CHANGE MODE
Procedure:
1. While pressing the [MUSIC] and [MULTI CH IN] buttons, press
the [POWER] button to turn on the main power.
2. Either the message “OFF” or “ON” appears.
RDS AUTOBETICAL MODE
Procedure:
1. While pressing the [MEMORY/ENTER] button, press the
[POWER] button to turn on the main power.
2. The message “Autobetical Select” appers and scans and stores
all the FM and FM RDS station in the broadcast area.
19
STR-DA1200ES
SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH], [MUSIC],
[MOVIE] button in order.
2. The message “MENU SPECIALIZED!” appears.
3. Each time the
3. Each time the
M
m
button of the remote commander is pressed, the item is switched in order as follows.
4. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH], [MUSIC], [MOVIE] button in order again.
5. The message “MENU SPECIALIZED OFF” appears.
5. The message “MENU SPECIALIZED OFF” appears.
Items
Protector on/off
Model version display
Model/destination change
FM/AM tuner version display
HDMI controller version display
HDMI controller update mode
Auto cal mic test
FL display fonts test
FL display test
Audio swap
DSP halt
DSP RAM
DSP Version display
Volume value display (FL/FR)
Volume value display (SL/SR)
Volume value display (CT/SW)
Volume value display
(SBL/SBR)
DAC mute information disclosure
1
DAC mute information disclosure
2
EERROM debug
Super reset
2nd volume value display
FL display duty change
YUV Y drive
Display
PROTECTOR ON/OFF [XXX]
##### *** vX. XX @@@@
MODEL [##### * * * *] X X
FM/AM Tuner Ver X. XX
HDMI Micom Ver X. XX
HDMIUcom Update [XXX]
SPEAKER OUT [XXXXX]
FL FONT 0x ** = [X]
ALL ON
SWAP [XXXXXXXXXXX]
DSP HALT [XXX]
[*****]=XXXXXXXX
DSP Ver S: ***, P: XXX
FL**** FR XXXX
SL**** SR XXXX
CT**** SW XXXX
SBL**** SBR XXXX
DAC MUTE U XXXXXXXX
DAC MUTE L XXXXXXXX
EEPROM [****] FR XX
SUPER RESET [XXX]
2nd VOLUME XXX
DARK OUT DUTY [XXX%]
YUV Y DRIVE [XX]
Remark
XXX: ON or OFF
(switching with
M
m
button of the remote commander)
#####: model
***: destination
X.XX: system controller software version
@@@@: Sum value of flash memory in the main system controller
#####: model, ****: destination, XX: at or fx
(switching with
M
m
button of the remote commander)
X.XX: FM/AM tuner controller software version
X.XX: HDMI controller software version
XXX: ON or OFF (switching with
M
m
button of the remote commander)
Reset control form the system controller side and the reset control from the
PC side interfere mutually when updating the HDMI controller and it
becomes writing NG
Therefore, when this mode is set to ON, the reset control from the system
controller side is not done
XXXXX: Selection of speaker output audio
[SOURCE]: nomally mode, [MIC]: mode that output audio from mic from
speaker
**: 20 to FE, X: character (switching with
M
m
button of the remote
commander)
Each time DISPLAY button to change as follows.
all on
→ test pattern 1 → test pattern 2 → all off → all on
Switching with
M
m
button of the remote commander
XXX: ON or OFF (switching with
M
m
button of the remote commander)
Mode not to send DSP host code, and to make only decipherment done
Mode that refers to internal RAM of DSP (for design evaluation)
***: DSP decoder patch version
XXX: DSP post process version
****: Front L-ch volume value
XXXX: Front R-ch volume value
****: Surround L-ch volume value
XXXX: Surround R-ch volume value
****: Center volume value
XXXX: Sub woofer R-ch volume value
****: Surround back L-ch volume value
XXXX: Surround back R-ch volume value
Display of module information to demand muting in system controller (for
design evaluation)
Display of module information to demand muting in system controller (for
design evaluation)
****: EEPROM address
XX: EEPROM data (switching with
M
m
button of the remote commander)
Not used for the servicing
If super reset is performed, “up convert signal level adjustment” will also be
initialized
When EEPROM initialization is required, perform the “all clear mode”
XXX: 2nd room volume value (00 to
∞)
XXX: Duty value of FL display (0% to 100%)
(switching with
M
m
button of the remote commander)
XX: Gain control value of brighness (00 to 1F)
(switching with
M
m
button of the remote commander)
Ver. 1.1
20
STR-DA1200ES
Items
YUV U drive
YUV V drive
Stop clock
Display
YUV U DRIVE [XX]
YUV V DRIVE [XX]
STOP CLK [XX] [XX] [XX]
Remark
XX: Gain control value of color difference (Cb) (00 to 1F)
(switching with
M
m
button of the remote commander)
XX: Gain control value of color difference (Cr) (00 to 1F)
(switching with
M
m
button of the remote commander)
Value of register related to clock of system controller display mode (for
design evaluation)
Click on the first or last page to see other STR-DA1200ES service manuals if exist.