Sony SS-ST3 Service Manual ▷ View online
SERVICE MANUAL
Sony Corporation
Published by Sony Techno Create Corporation
SS-ST3
SPECIFICATIONS
SPEAKER SYSTEM
9-893-831-01
2013I33-1
©
2013.09
AEP Model
UK Model
E Model
Australian Model
Ver. 1.0 2013.09
• SS-ST3 is Bar speaker in HT-ST3.
• All of the units included in the HT-ST3 (SS-ST3/
• All of the units included in the HT-ST3 (SS-ST3/
SA-WST3) are required to confi rming operation
of SS-ST3. Check in advance that you have all
of the units.
of SS-ST3. Check in advance that you have all
of the units.
Front L/Front R speakers
Speaker system
2-way speaker system, Passive radiator type
Speaker
Woofer: 30 mm × 100 mm cone type
Tweeter: 14 mm dome type
Passive radiator: 30 mm × 100 mm cone type
Tweeter: 14 mm dome type
Passive radiator: 30 mm × 100 mm cone type
Rated impedance
3 ohms
Center speaker
Speaker system
2-way speaker system, Acoustic suspension type
Speaker
Woofer: 30 mm × 100 mm cone type × 2
Tweeter: 14 mm dome type
Tweeter: 14 mm dome type
Rated impedance
3 ohms
General
Dimensions (approx.) (w/h/d)
900 mm × 40 mm × 32.5 mm (without stands)
900 mm × 42 mm × 30 mm (with stands)
900 mm × 42 mm × 30 mm (with stands)
Mass (approx.)
0.9 kg (with stands)
Design and specifications are subject to change without notice.
SS-ST3
2
SECTION 1
DISASSEMBLY
•
This set can be disassembled in the order shown below.
1-1. DISASSEMBLY FLOW
SET
1-2. GRILLE
FRAME
ASSY
(Page
3)
1-3. LOUDSPEAKER
(3 X 10 cm) (SP1)
(Page
4)
1-4. LOUDSPEAKER
(14 mm) (SP7)
(Page
4)
1-5. LOUDSPEAKER
(3 X 10 cm) (SP2)
(Page
5)
1-6. LOUDSPEAKER
(14 mm) (SP8)
(Page
5)
1-7. LOUDSPEAKER
(3 X 10 cm) (SP3, SP4)
(Page
6)
1-8. LOUDSPEAKER
(14 mm) (SP9)
(Page
7)
1-9. LOUDSPEAKER
(3 X 10 cm) (SP5, SP6)
(Page
7)
SS-ST3
3
Note: Follow the disassembly procedure in the numerical order given.
1-2. GRILLE FRAME ASSY
1 screw
(BVTP3
u 12)
5 screw
(BVTP3
u 12)
2 Loosen the screw about half.
6 boss
6 boss
Note 1: Please spread a sheet under a unit
not to injure grille frame assy.
4 Insert the jig into a space and
raise grille frame assy gradually.
Note
3: When using a jig, please work so
as not to injure grille frame assy
and speaker cabinet assy.
3 Press with a screwdriver screws
that were loosened.
Note
2: When pressing a screwdriver,
please be careful not to damage
the grille frame assy.
– Rear top view –
7 grille frame assy
4 Insert the jig into a space and
raise grille frame assy gradually.
Note
3: When using a jig, please work so
as not to injure grille frame assy
and speaker cabinet assy.
SS-ST3
4
1-3. LOUDSPEAKER (3 X 10 cm) (SP1)
1-4. LOUDSPEAKER (14 mm) (SP7)
– Front top view –
1 four screws
(BVTP3
u 10)
3 Remove
two
solders.
4 loudspeaker
(3
u 10 cm)
(SP1)
2 Remove the loudspeaker (SP1)
in the direction of an arrow.
3 Remove
two
solders.
Wire setting
[black]
loudspeaker (3
u 10 cm) (SP1)
[white]
[white]
[black]
:LUHVHWWLQJ
terminal position
1 four screws
(KTP3
u 10)
3 Remove
two
solders.
4 loudspeaker
(14
mm)
(SP7)
2 Remove the loudspeaker
(SP7) in the direction of
an
arrow.
[black]
loudspeaker (14 mm) (SP7)
[white]
–)URQWWRSYLHZ–