Sony SS-AC5 Service Manual ▷ View online
SS-AC5
5
2-4. LOUDSPEAKER 1.9 cm (ASSIST TWEETER) (SP1, SP2),
SPEAKER (2.5 cm) ASSY (MAIN TWEETER) (SP3)
3 Lift up the loudspeaker
1.9 cm (assist tweeter:
upper side) (SP1).
5 loudspeaker 1.9 cm
(assist
tweeter:
upper side) (SP1)
loudspeaker 1.9 cm (assist tweeter: upper side)
(SP1)
(SP1)
loudspeaker 1.9 cm
(assist tweeter:
upper side) (SP1)
“–” wire [black]
(assist tweeter:
upper side) (SP1)
“–” wire [black]
5 loudspeaker 1.9 cm
(assist
tweeter:
lower side) (SP2)
loudspeaker 1.9 cm
(assist tweeter:
lower side) (SP2)
“+” wire [gray]
(assist tweeter:
lower side) (SP2)
“+” wire [gray]
3 Lift up the loudspeaker
1.9 cm (assist tweeter:
lower side) (SP2).
speaker (2.5 cm) assy
(main tweeter)
(SP3)
(main tweeter)
(SP3)
packing (C)
boss
packing (C)
boss
convex
part
part
Note 2: When disassembling loudspeakers
1.9 cm (assist tweeter) (SP1, SP2),
place a stand etc. under tweeter assy
and be careful not to crush the convex
part of a speaker (2.5 cm) assy
(main tweeter) (SP3).
Note 10: When installing the loudspeakers 1.9 cm (assist tweeter)
(SP1, SP2), be sure to perform the polar check of "+" and
"í", to make "+" into the upper left side and to attach it,
as shown in the following figure.
Note 8: Check packing (C) not having
overlapped or not having run
aground.
Note 7: Do not touch
the convex part.
stand
stand
Note 11: Check that the connection mistake or insertion of a wire are not imperfect.
Note 12: Insert the terminal straightly.
Note 13: The arrangement of a wire should check that left side is gray and that right side is black.
Note 14: Check that a wire is on a speaker (2.5 cm) assy (main tweeter) (SP3).
Note 12: Insert the terminal straightly.
Note 13: The arrangement of a wire should check that left side is gray and that right side is black.
Note 14: Check that a wire is on a speaker (2.5 cm) assy (main tweeter) (SP3).
2 two screws (BVTP3 u 10)
Note
3: When tightening screws, be
careful not to put the wire of
loudspeakers.
Note
4: Check that the screw has not
floated or it is not slanting.
Note
5: Check that packing (C) has
not overflowed the edge of
loudspeakers.
Note
6: tightening torque: . . 1m
+RZWRLQVWDOOWKHORXGVSHDNHUFPDVVLVWWZHHWHU6363
,QVWDOOHGSRVLWLRQRISDFNLQJ&
1 terminal
[gray]
1 terminal
[black]
–,QQHUYLHZ–
–,QQHUERWWRPYLHZ–
–,QQHUYLHZ–
“+”
“–”
2 two screws (BVTP3 u 10)
Note
3: When tightening screws, be
careful not to put the wire of
loudspeakers.
Note
4: Check that the screw has not
floated or it is not slanting.
Note
5: Check that packing (C) has
not overflowed the edge of
loudspeakers.
Note
6: tightening torque: . . 1m
4 packing (C)
Note 9: The packing (C)
cannot
cannot
be
re-used.
Be sure to replace
it for new parts.
4 packing (C)
Note
9: The packing (C)
cannot
be
re-used.
Be sure to replace
it for new parts.
6 speaker (2.5 cm) assy
(main tweeter) (SP3)
loudspeaker 1.9 cm (assist tweeter: lower side)
(SP2)
(SP2)
Note 1: When replacing the loudspeaker 1.9 cm (assist tweeter) (SP1, SP2) and speaker (2.5 cm) assy
(main tweeter) (SP3), refer to “NOTE THE SPEAKER UNITS REPLACING” on page 2.
SS-AC5
6
2-5. TERMINAL BOARD ASSY (TB1)
Note 2: Please check direction of the upper and lower sides of terminal packing.
(Narrow side is the upper. Wide side is the bottom.)
Note 3: Check that terminal packing has not run aground with a terminal part.
Note 4: Push the whole terminal packing with a finger. Check the terminal
Note 4: Push the whole terminal packing with a finger. Check the terminal
packing not having shifted, not having floated or not being stuck.
Note 5: Check that terminal packing is not showing from screw holes of the
terminal board assy (TB1).
2 Pull out the terminal
board assy (TB1).
4 terminal packing
terminal board
assy “–” terminal
assy “–” terminal
terminal board
assy “+” terminal
assy “+” terminal
3 terminal [black]
terminal [black]
terminal [black]
3 terminal [red]
terminal [red]
terminal [red]
terminal [black]
WO board
wire [black]
wire [black]
terminal [red]
terminal packing
terminal
Narrow side
upper side
Wide side
– Rear view –
– Top view –
Note 6: Check direction of terminals.
(terminal (black) is left side.
terminal (red) is right side.)
Note 7: Check that the caulking part of a terminal
has faced upward.
Note 8: Be careful not to attach a crack to a speaker
cabinet using the terminal of a wire.
Note 9: Check whether the terminal is inserted
conversely.
Note 10: Insert the terminal straightly.
Note 11: After terminal insertion, should check
conversely.
Note 10: Insert the terminal straightly.
Note 11: After terminal insertion, should check
acting as lock of the terminal completely.
:ire VeWWiQJ
+ow Wo iQVWaOO WKe WerPiQaO paFNiQJ
1 four screws (3.5 u 20)
Note
1: tightening torTue 1. .1 Nm
5 terminal board assy
(TB1)
WO board
wire [red]
wire [red]
terminal
SS-AC5
7
2-6. SPEAKER (13 cm) (WOOFER) (SP4)
2 Pull out the speaker (13 cm)
(woofer)
(SP4).
3 terminal
[green/black]
3 terminal [green]
speaker terminal
position
position
4 packing (13 cm)
Note
5: When installing the packing (13 cm), a glossy
surface is made into the speaker cabinet side,
and a rough side is made into the loudspeaker
side, and align the position of the screw hole
of packing (13 cm) and speaker cabinet.
5 speaker (13 cm) (woofer) (SP4)
Note
7: When installing the speaker (13 cm) (woofer) (SP4),
be careful not to attach a crack to a speaker cabinet using
the terminal of a wire.
Note
8: Be careful not to put a wire.
Note
9: Check that the connection mistake or insertion of a wire are
not
imperfect.
Note
10: Insert the terminal straightly.
Note
11: After terminal insertion, should check acting as lock of the
terminal
completely.
Note
12: Be careful not to attach a crack to the edge of a speaker cabinet.
Note
13: Check packing (13 cm) not being twisted or not having fallen
into a speaker cabinet.
Note 6: When installing the speaker (13 cm) (woofer) (SP4),
after each screw holes of the speaker (13 cm) (woofer)
(SP4) and packing (13 cm) are aligned, attach it to the
speaker
cabinet.
Note 1: When installing the speaker (13 cm) (woofer) (SP4),
install to a speaker cabinet after checking that a speaker
terminal is on the diagonal left.
Note 2: Do not touch the central part of the
speaker (13 cm) (woofer) (SP4).
Note 3: Check that the caulking portion of a terminal is
inside suitable (speaker side).
:LUHVHWWLQJ
speaker (13 cm) (woofer)
(SP4) “–” terminal
(SP4) “–” terminal
speaker (13 cm) (woofer)
(SP4) “+” terminal
(SP4) “+” terminal
terminal
WO board (MT2)
“W1–” wire [green/black]
“W1–” wire [green/black]
WO board (MT2)
“W1+” wire [green]
“W1+” wire [green]
1 four screws (4 u 25)
Note
4:
tightening torTue 1. .1 1m
SS-AC5
8
2-7. TW BOARD BLOCK, WO BOARD BLOCK
5 TW board block
2 Remove four catchers from four shafts
of the speaker cabinet.
4 four terminals
2 Remove four catchers from four shafts
of the speaker cabinet.
6 WO board block
Note 5: Check that the caulking portion of a terminal is outside suitable.
Note 6: Check that the connection mistake or insertion of a wire are not imperfect.
Note 7: Insert the terminal straightly.
Note 8: After terminal insertion, should check acting as lock of the terminal completely.
Note 6: Check that the connection mistake or insertion of a wire are not imperfect.
Note 7: Insert the terminal straightly.
Note 8: After terminal insertion, should check acting as lock of the terminal completely.
1 tapping screw (3.5 u 16)
Note
1: When tightening screws, be careful
not to put the wire.
Note
2: Check that the screw has not floated
or it is not slanting.
Note
3: When tightening screws, be careful
so that screw driver and screw
do not touch capacitor.
Note
4: WLJKWHQLQJWRUTXH1P
TW board (MT1)
TW board
“TW IN–” wire
[brown]
“TW IN–” wire
[brown]
TW board
“TW IN+” wire
[blue]
“TW IN+” wire
[blue]
:LUHVHWWLQJ
caulking portion
WO board block
shaft
shaft
shaft
shaft
–6SHDNHUFDELQHWULJKWLQVLGHFURVVVHFWLRQDOYLHZ–
–6SHDNHUFDELQHWOHIWLQVLGHFURVVVHFWLRQDOYLHZ–
TW board block
shaft
shaft
shaft
shaft
1 tapping screw (3.5 u 16)
Note
1: When tightening screws, be careful
not to put the wire.
Note
2: Check that the screw has not floated
or it is not slanting.
Note
3: When tightening screws, be careful
so that screw driver and screw
do not touch capacitor.
Note
4: WLJKWHQLQJWRUTXH1P
3 Pull out the TW board block and the
WO board block from speaker cabinet.
caulking
portion
portion
WO board
(MT2)
(MT2)
TW board
“AT IN–” wire
[brown]
“AT IN–” wire
[brown]
TW board
“AT IN+” wire
[blue]
“AT IN+” wire
[blue]
–6SHDNHUFDELQHWLQQHUYLHZ–
Push the WO board lead
wire (red) through the slit
in the acoustic absorbent.
Note 9: Looking from the
wire (red) through the slit
in the acoustic absorbent.
Note 9: Looking from the
woofer side, the wire
on the left is red.
Push the WO board lead
wire (black) through the slit
in the acoustic absorbent.
Note 9: Looking from the
wire (black) through the slit
in the acoustic absorbent.
Note 9: Looking from the
woofer side, the wire
on the right is black.
Pass the two wires in between
the right duct and the acoustic
absorbent, and then bring them
towards the woofer opening.
the right duct and the acoustic
absorbent, and then bring them
towards the woofer opening.
Click on the first or last page to see other SS-AC5 service manuals if exist.