Sony SRS-X99 Service Manual ▷ View online
SRS-X99
25
2-21. FERRITE CORE (FC1)
2 filament tape
(sub
material)
cushion
(ferrite core)
(ferrite core)
3 ferrite core (FC1)
ferrite core
(FC1)
(FC1)
Wrap once.
50 ± 1 mm
filament tape
(sub material)
(sub material)
AC inlet (2P)
(AC1)
(AC1)
+RZWRLQVWDOOWKHIHUULWHFRUH)&
1 cushion (ferrite core)
SRS-X99
26
2-22. AC INLET (2P) (AC1)
– Rear bottom view –
7 cushion (wire)
cushion (wire)
cushion (wire)
cushion (wire)
printing side
cushion (wire)
cushion (E)
9 bracket (AC)
bracket (AC)
7 cushion (wire)
8 claw
8 claw
0 AC inlet (2P)
(AC1)
sealing plate (AC) block
short
long
AC inlet wire
4 Draw out the AC inlet block
from the hole.
5 AC inlet
block
hole
1 two tapping
screws
(P
(P
B2.6
u 8)
3 two tapping
screws
(P
(P
B2.6
u 8)
2 sealing plate (AC) block
$&LQOHWZLUHVHWWLQJ
AC inlet wire
groove
6 cushion (E)
40 mm
cushion (E)
[white]
guide line
+RZWRLQVWDOOWKHVHDOLQJSODWH$&EORFN
cushion (wire)
[white]
3DVWLQJSRVLWLRQRIWKHFXVKLRQ
,QVWDOODWLRQGLUHFWLRQIRUWKHEUDFNHW$&
Note: Lay a soft piece of cloth under the unit
to avoid damaging the top panel.
SRS-X99
27
SECTION 3
TEST MODE
Buttons and indicators position:
Rear of the unit
To display the function buttons:
Place your hand as illustrated below to display the function but-
tons. To display quickly, touch the center of the top panel.
tons. To display quickly, touch the center of the top panel.
FIRMWARE VERSION AND WIFI MODULE CHAN-
NEL SETTING DISPLAY MODE
NEL SETTING DISPLAY MODE
1. Firmware version display
It can check the fi rmware version.
It can check the fi rmware version.
Procedure:
1. Touch the [?/1] button to turn the power on.
2. While pressing the [WPS] button, touch the [VOL –] button.
3. Touch the [AUDIO IN] → [ PAIRING] → [VOL –] button
1. Touch the [?/1] button to turn the power on.
2. While pressing the [WPS] button, touch the [VOL –] button.
3. Touch the [AUDIO IN] → [ PAIRING] → [VOL –] button
in order (in less than 3 seconds).
4. It
enters
the
system
fi rmware version display mode, the [?/1]
indicator lights off and the [AUDIO IN] indicator blinks.
light off
blinking
Button input settings under operation of fi rmware ver-
sion display mode:
•
sion display mode:
•
Touch the [AUDIO IN] button.
System
fi rmware version display mode ([AUDIO IN] indicator
blinks)
•
Touch the [NETWORK] button.
WiFi
module
fi rmware version display mode ([NETWORK]
indicator blinks)
•
Touch two buttons of [ PAIRING] and [VOL +] simultaneously.
Bluetooth
module
fi rmware version display mode ([ PAIR-
ING] indicator blinks)
•
Touch the [ PAIRING] button.
The major version in each fi rmware version display mode is
displayed.
displayed.
•
Touch the [VOL –] button.
The minor version (upper) in each fi rmware version display
mode is displayed.
mode is displayed.
•
Touch the [VOL +] button.
The minor version (lower) in each fi rmware version display
mode is displayed.
mode is displayed.
Each fi rmware version is shown by the blinking frequency of the
[?/1] indicator.
[?/1] indicator.
blinking
Example: When the version is “1.23”
When touching the [ PAIRING] button, the [?/1] indicator
blinks 1 time (cycle of the 1 second).
When touching the [VOL –] button, the [?/1] indicator blinks 2
times (cycle of the 1 second).
When touching the [VOL +] button, the [?/1] indicator blinks 3
times (cycle of the 1 second).
When touching the [ PAIRING] button, the [?/1] indicator
blinks 1 time (cycle of the 1 second).
When touching the [VOL –] button, the [?/1] indicator blinks 2
times (cycle of the 1 second).
When touching the [VOL +] button, the [?/1] indicator blinks 3
times (cycle of the 1 second).
SRS-X99
28
2. WiFi module channel setting display
It can check the channel setting of the WiFi module.
It can check the channel setting of the WiFi module.
Procedure:
1. While entering the any fi rmware version display mode, touch
1. While entering the any fi rmware version display mode, touch
the two buttons of [NETWORK] and [AUDIO IN] simultane-
ously.
ously.
2. It enters the WiFi module channel setting display mode, the
[NETWORK] and [LINK] indicators blink.
blinking
3. When touching the [VOL +] button, channel setting of the 2.4
GHz band is shown by the blinking (cycle of the 1 second)
frequency of the [?/1] indicator.
frequency of the [?/1] indicator.
4. When touching the [VOL –] button, channel setting of the 5
GHz band is shown by the blinking (cycle of the 1 second)
frequency of the [?/1] indicator.
frequency of the [?/1] indicator.
Blinking
frequency
Channel setting
2.4 GHz band
5 GHz band
1
1 – 13 ch
36 – 165 ch
2
–
36 – 116 ch,
132 – 165 ch
3
1 – 11 ch
–
4
–
149 – 161 ch
5
–
–
6
–
36 – 140 ch
7
–
36 – 64 ch,
149 – 165 ch
blinking
3. Releasing method
Touch the [?/1] button to turn the power off.
Touch the [?/1] button to turn the power off.
WIRELESS LAN RF RECEPTION LEVEL DIS-
PLAY MODE
PLAY MODE
It can check the RF reception level at the time of wireless LAN
connection.
connection.
Necessary Equipment:
• Access point supporting WPS
• Access point supporting WPS
Procedure:
1. Touch the [?/1] button to turn the power on, and check that the
1. Touch the [?/1] button to turn the power on, and check that the
[LINK] indicator lights off.
2. Press and hold the [WPS] button for about 2 seconds until the
beep sound occurs, the [LINK] indicator blinks in orange.
3. Press the [WPS] button on the access point.
4. Check that wireless LAN connection is completed and the
4. Check that wireless LAN connection is completed and the
[LINK] indicator lights up in orange.
5. Touch and hold the [NETWORK] button until the beep sound
occurs, enter the wireless LAN RF reception level display
mode, and the reception level is shown by the blinking of func-
tion indicators.
mode, and the reception level is shown by the blinking of func-
tion indicators.
Reception
level
Function indicators
NET-
WORK
PAIRING
USB-A
USB-B
AUDIO
IN
Level = 0 %
Light off
Light off
Light off Light off Light off
0 % < Level,
Level < 20 %
Level < 20 %
Blinking
Light off
Light off Light off Light off
20 %
≤ Level,
Level < 40 %
Blinking
Blinking
Light off Light off Light off
40 %
≤ Level,
Level < 60 %
Blinking
Blinking
Blinking Light off Light off
60 %
≤ Level,
Level < 80 %
Blinking
Blinking
Blinking Blinking Light off
80 %
≤ Level,
Level
≤ 100 %
Blinking
Blinking
Blinking Blinking Blinking
light off or blinking
Releasing method:
Touch the any button.
Touch the any button.
Click on the first or last page to see other SRS-X99 service manuals if exist.