DOWNLOAD Sony SRS-X99 Service Manual ↓ Size: 4.88 MB | Pages: 38 in PDF or view online for FREE

Model
SRS-X99
Pages
38
Size
4.88 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
srs-x99.pdf
Date
PREV: Sony SRS-X77 Service Manual

Sony SRS-X99 Service Manual ▷ View online

SRS-X99
17
2-10.  PLATE (U) (US,  CND)
2-11.  SUBWOOFER (94 mm) (SP7)
1 two tapping screws
 (BV 
B3 
u 10)
2 plate (U)
– Baffle block bottom rear view –
Left side
Bottom side
1 tapping screw
 (BV 
B3 
u 10)
1 tapping screw
 (BV 
B3 
u 10)
1 two tapping screws
 (BV 
B3 
u 10)
2 loudspeaker (94 mm) 
 (subwoofer) 
(SP7)
– Baffle block top rear view –
(Except US, CND)
‡ ,QVtallatioQ GirectioQ for tKe loXGVpeaker ( PP) 
  (VXbwoofer) (S3)
Top side
label
Left side
Left side
Right side
Note: When installing the loudspeaker (94 mm) 
 
(subwoofer) (SP7), make the position of 
 
label as shown in the figure below.
loudspeaker (94 mm) 
(subwoofer) (SP7)
SRS-X99
18
2-12.  LOUDSPEAKER (6.8 × 9.5 cm)  PASSIVE (SP3,  SP4)
2-13.  BLUETOOTH  MODULE (BT1)
2 loudspeaker (6.8 u 9.5 cm) 
 passive 
(L-ch) 
 (SP3)
2 loudspeaker (6.8 u 9.5 cm) 
 passive 
(R-ch) 
 (SP4)
1 three tapping screws
 (BV 
B3 
u 10)
1 four tapping screws
 (BV 
B3 
u 10)
– Baffle block top rear view –
1 tapping screw
 (BV 
B3 
u 10)
(Except US, CND)
Top side
Left side
3 tapping screw
 (P 
B2.6 
u 6)
2 flexible flat cable (10 core)
 (FFC2)
5 bluetooth module
 (BT1)
1 filament tape 
 (sub 
material)
bluetooth module 
(BT1)
terminal side
filament tape 
(sub material)
flexible flat cable (10 core) 
(FFC2)
colored line
Insert straight into the interior.
flexible flat 
cable
connector
OK
colored line
Insert at a slant.
flexible flat 
cable
connector
NG
‡ How to install the flexible flat cable
  When installing the flexible flat cable, ensure that 
  the colored line is parallel to the connector after insertion.
‡:LUHVHWWLQJ
4 adhesive A
SRS-X99
19
2-14.  FLEXIBLE  FLAT  CABLE (10  CORE) (FFC2)
5 MAIN board connector
 (CN010)
6 flexible flat cable (10 core)
 (FFC2)
flexible flat cable (10 core)
(FFC2)
1 MAIN board flexible flat cable 
 
(25 core) (CN015)
2 Peel off two adhesive sheets.
3 Peel off the adhesive 
 
sheet (BT FFC).
colored line
Insert straight into the interior.
flexible flat 
cable
connector
OK
colored line
Insert at a slant.
flexible flat 
cable
connector
NG
‡ How to install the flexible flat cable
  When installing the flexible flat cable, ensure that 
  the colored line is parallel to the connector after insertion.
4 filament tape 
 (sub 
material)
‡ :iUe settinJ
‡ :iUe settinJ
Top side
filament tape 
(sub material)
MAIN board
Terminal face 
is below side.
CN010
flexible flat cable (10 core)
(FFC2)
guide line
shield plate (K) block
SRS-X99
20
2-15.  SHIELD  PLATE (K)  BLOCK
8 tapping screw
 (BV 
B3 
u 10)
7 copper leaf sheet (plate)
8 two tapping 
 screws 
 (BV 
B3 
u 10)
3 card WLAN/BT combo
 connector
0 shield plate (K) block
8 five tapping screws
 (BV 
B3 
u 10)
4 filament tape 
 (sub 
material)
filament tape 
(sub material)
2 connector 
 (CN403)
1 Remove the sleeve ferrite clamp 
 
(FC3) and wire from the clamp.
power case (U)
shield plate (K) block
filament tape 
(sub material)
copper leaf sheet (plate)
‡$QWHQQDZLUHVHWWLQJ
6 filament tape 
 (sub 
material)
5 
antenna wire
 (CON4)
antenna wire
(CON4)
MAIN board
card WLAN/BT combo
sleeve ferrite clamp 
(FC3)
clamp
Insert only part way.
Insert straight into 
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
‡+RZWRLQVWDOOWKHFRQQHFWRU
  Insert the connector straight into the interior. 
  There is a possibility that using this unit without 
  the connector correctly installed will damage it.
‡:LUHVHWWLQJ
9 screw 
 (BVTT2.6 
u 4)
‡3DVWLQJSRVLWLRQRIWKHFRSSHUOHDIVKHHWSODWH
Note 2: Connect the antenna wire to the terminal 
 
on the "V" mark side.
Note 1: Sleeve ferrite clamp (FC3) has been deleted 
 
in the midway of production. 
 
(Except Chinese and Taiwan models)
Ver. 1.1
Page of 38
Display

Click on the first or last page to see other SRS-X99 service manuals if exist.

RANDOM: