DOWNLOAD Sony SCD-C222ES Service Manual ↓ Size: 6.62 MB | Pages: 98 in PDF or view online for FREE

21

Items

Description

Remarks

HENSHIN RYOU

Eccentricity measurement

For the CD only are measured

Eccentricity (actual eccentric amount) of disc, disc pulley total

• Read by dividing by 10
• 0 may be displayed if eccentricity

is small (10um or less) (Due to
measurement reason)

SPIN DOWN TIME (msec)

Time from spindle brake application to rotation stop

FG (IC901 pin ys) monitoring

LOAD OUT TIME (msec)

Time until loading table comes out from the state where a disc is in chuck

Loading out switch    H

tL

Measured Data Reading Method:
To judge the check result, the measured data must be read.
1. When “AUTO CHECK OK” is displayed, rotate the 

[        AMS        ]

 dial clockwise by 2 clicks.

2. When “13. DISP RSLT?” is displayed, press the 

[        AMS        ]

 dial to enter.

3. “PLEASE WAIT” will be displayed and in several seconds, “13. DISP RESULT” will be displayed.
4. Rotate the 

[        AMS        ]

 dial clockwise by 1 click, and the “LOAD IN” will be displayed.

5. Press the 

[        AMS        ]

 dial to enter.

6. Compare the displayed value with the following specified value.
7. Hence, repeat step 4 to 6 (display is variable) and read the measured data respectively.
8. Compare the measured data with the specified value to check for NG item.

Blank display of measured value means that an error occurred during the checking or no measurement was taken place.

Specified Value:
(1) SACD (Use the test disc SATD-S5 or SATD-S4)

Measured values in check items are typical ones.

Check items

Specified value

LOAD IN TIME (msec)

:

Not displayed in this set.

SPIN UP TIME (msec)

: 1993

1800 to 2450

PF/VC/FE/TE AVRG (ORG) : 8E, E, 1E2, 12

RF: 91-C8, VC: 1F8-8, FE: 1D1-30, TE: 198-75

PF/VC/FE/TE AVRG (ADJ) : 9D, E, 6, 2

RF: 91-AF, VC : 1F8-8, FE: 1EE-12, TE: 1EA-16

PI/TRVS PP (ORG/ADJ)

: 80, 129, 100, 90

PI ORG: 80-100,  PI ADJ: 80-95, TRVS ORG: 53-118, TRVS ADJ: 45-132

PIOR/CCR/TRCR

: 1B, 31, 1F

No specified value given

FOCUS/TRK GAIN

: 29, 35

FOCUS: 1E-35, TRK: F-40

FBIAS/TRVSC/TRCR2

: 2FE, 14, 6

F.BIAS: 1E2-3A, TRVSC: 1E4-4D    TRCR2: no specified value given

READ TOC TIME (msec)

: 1098

1350 to 2050

PSP AMPLITUDE

: 2387

1450 to 2150

1/3 SEEK TIME

: 2268581, 625121, <_>, 1446850

F) AVE/MIN/MAX (msec)

: 926, 909, 938

AVE: 1150 msec or less, MAX: 1300 msec or less

R) AVE/MIN/MAX (msec)

: 919, 901, 937

AVE: 1150 msec or less, MAX: 1300 msec or less

1/MAX SEEK TIME

: 2268581, 0, <_>, 2268581

F) AVE/MIN/MAX (msec)

: 1846, 1819, 1879

AVE: 2250 msec or less, MAX: 2500 msec or less

R) AVE/MIN/MAX (msec)

: 1837, 1829, 1849

AVE: 2250 msec or less, MAX: 2500 msec or less

ERROR RATE
PO MAX/AVE FRAME

: 0, 0

MAX: 0, AVE: 0

PO MAX/AVE NUM

: 480, 28

MAX: 1500 or less, AVE: 200 or less

PI1 MAX/AVE FRAME

: 0, 0

MAX: 0, AVE: 0

PI1 MAX/AVE NUM

: 320, 11

MAX: 1500 or less, AVE: 200 or less

PI2 MAX/AVE FRAME

: 0, 0

MAX: 0, AVE: 0

PI2 MAX/AVE NUM

: 41, 0

MAX: 1500 or less, AVE: 200 or less

SPIN DOWN TIME (msec)

: 1312

1300 to 2100

LOAD OUT TIME (msec)

Not displayed in this set.

l

L

l

L

l

L

l

L

* Items are not used in the

SATD-S5.

22

(2) CD (Use the test disc PATD-012 or YEDS-18)

Measured values in check items are typical ones.

Check items

Specified value

LOAD IN TIME (msec)

:

Not displayed in this set.

SPIN UP TIME (msec)

: 1354

1300 to 1600

RF/VC/FE/TE AVRG (ORG)

: 8E, D, 1E3, 12

RF: 91-C8, VC: 1F8-8, FE: 1D1-30, TE: 198-75

RF/VC/FE/TE AVRG (ADJ)

: 9C, C, 6, 2

RF: 91-AF, VC: 1F8-8, FE: 1EE-12, TE: 1EA-16

PI/TRVS PP(ORG/ADJ)

: 84, 128, 100, 90

PI ORG: 80-100,  PI ADJ: 80-95, TRVS ORG: 55-155, TRVS-ADJ: 50-120

PIOR/CCR/TRCR

: 1B, 11, 1E

No specified value given

FOCUS/TRK GAIN

: 33, 28

FOCUS: 24-53, TRK: 1A-4E

FBIAS/TRVSC/TRCR2

: 10, 0, 5

F.BIAS: 1D9-2A,  TRVSC: 1E2-19    TRCR2: no specified value given

MIN JITTER AT F.BIAS

: 147

700 or less

READ TOC TIME (msec)

: 827

1150 to 3150

1/3 SEEK TIME

: 311660, 103786, <_>, 207722

F) AVE/MIN/MAX (msec)

: 794, 699, 908

AVE: 1200 msec or less, MAX: 1300 msec or less

R) AVE/MIN/MAX (msec)

: 824, 661, 920

AVE: 1200 msec or less, MAX: 1300 msec or less

1/MAX SEEK TIME

: 311660, 0, <_>, 311660

F) AVE/MIN/MAX (msec)

: 1991, 1964, 2015

AVE: 2200 msec or less, MAX: 2500 msec or less

R) AVE/MIN/MAX (msec)

: 1711, 1701, 1726

AVE: 2200 msec or less, MAX: 2500 msec or less

ERROR RATE
C1 MAX/AVE

: 3, 0

C1  MAX: 15 or less

C2 MAX/AVE

: 0, 0

C2  MAX: 0

HENSHIN RYOU (1/10um)

: 168

800 or less (100 um or less)

SPIN DOWN TIME (msec)

: 1342

450 to 1500

LOAD OUT TIME (msec)

Not displayed in this set.

RF, VC, FE, TE, FBIAS and TRVSC measured values are hexadecimal data with positive and negative signs. When comparing the measured
value with the specified value, refer to the following.

23

(• Perform as necessary)
The stability of the set can be checked by repeating the combined
operation of focus jump (layer 0

t1, layer 1t0) and access to

the most inward track

ymost outward track by the set number of

times or until an error occurs using the dual layer HD disc, DL
disc.
A set of operation including an access to the layer 0 (most inward
track)

tlayer 0 (most outward track)tfocus jump (layer

0

t1)tlayer 1 (most outward track)tlayer 1 (most inward

track)

tfocus jump (layer 1t0) is carried out repeatedly by the

set number of times.

Checking Method:
1. After setting the test mode, rotate the 

[        AMS        ]

 dial to

select “92. SET CHECK” and press the 

[        AMS        ]

 dial

to enter.

2. When “SET TEST START” is displayed, rotate the

[        AMS        ]

 dial clockwise by 3 clicks to display “2.

F.JMP CHECK?”.

3. Press the 

[    OPEN/CLOSE]

 button to open the tray, and place

the DL disc.

4. Press the 

[        AMS        ]

 dial to load the tray into the set.

5. “NOW SET UP” will be displayed and the DL disc setup will

start. (It takes about ten and several seconds to set up the disc
as two layers of layer 0 and layer 1 are adjusted)

6. At the completion of setup, “F.JUMP TIMES” will be dis-

played.

7. Rotate the 

[        AMS        ]

 dial clockwise by 5 clicks to display

“5”. (If 5 sets of operation is executed *1)

8. Press the 

[        AMS        ]

 dial, and the check will start.

9. Immediately when the check finished, “UP MAX

ssss”

t“UP AVE ssss”t“DW MAX

ssss”

t“DW AVE ssss”t“F.JMP OK 

[TIMES]

”

will be displayed repeatedly. (s denotes the measured value
in msec)
UP MAX: Max time required for layer 0 (most inward

track)

tlayer 0 (most outward track)tfocus jump

(layer 0

t1)

UP AVE:

Average time required for layer 0 (most inward
track)

tlayer 0 (most outward track)tfocus jump

(layer 0

t1)

DW MAX: Max time required for layer 1 (most outward

track)

tlayer 1 (most inward track)tfocus jump

(layer 1

t0)

DW AVE: Average time required for layer 1 (most outward

track)

tlayer 1 (most inward track)tfocus jump

(layer 1

t0)

Specified value: 7000 msec or less (if no error occurred)
If an error occurred due to defocusing during the checking,
refer to the following error list. (page 25)

10. Press the 

[    OPEN/CLOSE]

 button, and the disc will be ejected

and the check will finish. Also, if the 

[        AMS        ]

 dial is

pressed in step 9, “2. F.JUMP CHK OK” will be displayed.
Then, if the 

[        AMS        ]

 dial is again pressed, “2. F.JMP

CHECK” will be displayed instantaneously and a recheck is
enabled from the step 5 in the same manner.

*1 Setting arbitrary number of times instead of 5 allows the check-

ing to be repeated by the set number of times. Also, setting 0
(zero) allows the aging check to be repeated until an error oc-
curs.

(• Perform as necessary)
This test checks the auto adjustment time required when the disc
is switched between HD (SACD) layer and CD layer. This test is
conducted to check the stability in switching from CD to SACD,
or SACD to CD in the HYBRID disc.
A set of operation including CD layer stop state

tHD layer auto

adjustment

tHD layer TOC readingtHD layer stop statetCD

layer auto adjustment

tCD layer TOC readingtCD layer stop

state is repeated by the set number of times.

Checking Method:
1. After setting the test mode, rotate the 

[        AMS        ]

 dial to

select “92. SET CHECK” and press the 

[        AMS        ]

 dial

to enter.

2. When “SET TEST START” is displayed, rotate the

[        AMS        ]

 dial clockwise by 4 clicks to display “3.

HYB CHECK?”.

3. Press the 

[    OPEN/CLOSE]

 button to open the tray, and place

the HYBRID disc.

4. Press the 

[        AMS        ]

 dial to load the tray into the set.

5. “NOW SET UP” will be displayed and the HYBRID disc setup

will start. (It takes about several seconds to set up the disc *1)

6. At the completion of setup, “CHANGE TIMES?” will be dis-

played.

7. Rotate the 

[        AMS        ]

 dial clockwise by 5 clicks to display

“5” (if 5 sets of operation is executed *2)

8. Press the 

[        AMS        ]

 dial, and “START” will be displayed

and the check will start. During the check, the following will
be displayed.
“CD—>HD” display: Time from switching from CD layer to

HD layer up to start of play is measured.

“HD—>CD” display: Time from switching from HD layer to

CD layer up to start of play is measured.

9. Immediately when the check finished, “CD MAX

ssss”

t“CD AVE ssss”t“HD MAX

ssss”

t“HD AVE ssss” will be displayed

repeatedly. (s denotes the measured value in msec)
Specified value: 10000 msec or less (if no error occurred)
If an error occurred due to defocusing during the checking,
refer to the following error list. (page 25)

10. Press the 

[    OPEN/CLOSE]

 button, and the disc will be ejected

and the check will finish. Also, if the 

[        AMS        ]

 dial is

pressed in step 9, “HYB CHK OK” will be displayed. Then, if
the 

[        AMS        ]

 dial is again pressed, “HYBRID CHECK”

will be displayed instantaneously and a recheck is enabled from
the step 5 in the same manner.

*1 “NOW SET UP” display may continue for several minutes

and an error may be displayed depending on the discs. In this
case, press the 

[        AMS        ]

 dial again.

*2 Setting arbitrary number of times instead of 5 allows the check-

ing to be repeated by the set number of times. Also, setting 0
(zero) allows the aging check to be repeated until an error oc-
curs

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

l

L

A

A

A

A

24

Measurement of table rotation hours, tray open/close hours and
panel door open close hours can be executed together with CDM59.

Procedure
1. Set the test mode. Turn the 

[         AMS         ]

 dial and select

59 Table Init. Press 

[        AMS        ]

 once (that enables the

[    OPEN/CLOSE]

 key.)

2. When the message INITIAL OK appears, press the 

[    OPEN/

CLOSE]

 key to eject the tray. Place a disc in the DISC1 of the

table. (Be sure to place a disc in DISC1. If a disc is placed in
any locations other than DISC1, the correct measurement can-
not be executed. Therefore, be sure to place a disc in DISC by
using the 

[DISC SKIP]

 key.)

3. Select 58 CDM Check by turning 

[        AMS        ]

 and press

[        AMS        ]

 once.

4. Measurement starts automatically.
5. When the measurement is completed, the message DOOR OP

ss.s (s is a decimal number) appears on the fluorescent
indicator tube.

6. Result of measurement can be check by turning 

[        AMS        ]

.

If any measurement item does not meet specification, a mes-
sage “ng” is displayed next to the measurement value.

7. When you want to repeat the test, press 

[        AMS        ]

 again.

8. Press the 

[    OPEN/CLOSE]

 key to terminate the test and re-

move the disc.
* 1.The measurement can be performed without placing a disc.

However, the BU chucking time and unchucking time will
be slightly different from the actual values.

* 2.When the machine enters this mode once, it cannot return

to the normal test mode. If any other tests are desired, turn
off the main power once and then back on again to enter
the test mode.

l

L

l

L

l

L

l

L

Measurement item

Description

Specifications (unit: second)

RL

Time required for the table to make one complete rotation.

6.0 to 7.5

(R: Clockwise rotation. L: Counter-clockwise rotation)

CLOSE

Time required to close the tray.

<3.7

BU UP

Time required for the BU block to perform chucking from the DOWN position

<1.4

EXOPEN

The XCHANGE OPEN time

<2.6

EXCLOSE

The EXCHANGE CLOSE time

<3.8

BU DOWN

Time required for the BU block to perform unchucking and going to the DOWN

<2.7

position

OPEN

Time required to open the tray

<3.2

l

L

l

L

A

A

A