DOWNLOAD Sony SAVA-D900 / SAVA-D900FR / SAVA-D900R / SS-T900 Service Manual ↓ Size: 32.06 MB | Pages: 99 in PDF or view online for FREE

25

1

 : Emergency Code

2

 : Don’t Care

These codes are used for verification of software designing.

3

 : Historical order 1 to 9

Emergency Codes List

10: Communication to IC001 (TK board) failed.
11: Each servo for focus, tracking, and spindle is unlocked.
12: Communication to EEPROM, IC201 (DVD board) failed.
13: Writing of hours meter data to EEPROM, IC201 (DVD board)

failed.

14: Communication to Servo DSP IC701 (DVD board) failed, or

Servo DSP is faulty.

20: Initialization of tilt servo and sled servo failed. They are not

placed in the initial position.

21: Tilt servo operation error
22: Syscon made a request to move the tilt servo to wrong posi-

tion.

23: Sled servo operation error
24: Syscon made a request to move the sled servo to wrong posi-

tion.

30: Tracking balance adjustment error
31: Tracking gain adjustment error
32: Focus balance adjustment error
33: Focus bias adjustment error
34: Focus gain adjustment error
35: Tilt servo adjustment error
36: RF equalizer adjustment error
37: RF group delay adjustment error
38: Jitter value after adaptive servo operation is too large.
40: Focus servo does not operate.
41: With a dual layer (DL) disc, focus jump failed.50: CLV

(spindle) servo does not operate.

51: Spindle does not stop.
60: With a DVD disc, Syscon made a request to seek nonexistent

address.

61: With a CD disc, Syscon made a request to seek nonexistent

address.

62: With a CD disc, Syscon made a request to seek nonexistent

track No. and index No.

63: With a DVD disc, seeking of target address failed.
64: With a CD disc, seeking of target address failed.
65: With a CD disc, seeking of target index failed.
70: With a DVD disc, physical information data could not be read.
71: With a CD disc, TOC data could not be read.
80: Disc type judgment failed.
81: As disc type judgment failed, retry was repeated.
82: As disc type judgment failed, a measurement error occurred.
83: Disc type could not be judged within the specified time.
84: Illegal command code was received from Syscon.
85: Illegal command was received from Syscon.

1.0 

±

 0.02 Vp-p

## Version Information ##

IF con.

Ver. x. xxx (xxxx)

Group    00

SYScon.

Ver. x. xxx (xxxx)

Model    xx

Region   0x

SW1      ??

SW2      ??

Exit: RETURN

On the Test Mode Menu screen, selecting 

[5]

 displays the ROM

version and region code.
The parenthesized hexadecimal number in version field is checksum
value of ROM.

On the Test Mode Menu screen, selecting 

[6]

 displays color bars

for video level adjustment. During display of color bars, OSD
disappears but the menu screen will be restored if pressing any key.

Measurement point

: LINE OUT VIDEO

(75 

Ω

 terminating resistance)

Measuring instrument : Oscilloscope
Adjustment device

: RV401 on DVD board

Specified value

: 1.0 ± 0.02 Vpp

3

1.

1

2

2

26

: During diagnostic check, the characters and color bars can

be seen only with the NTSC monitor. Therefore, for
diagnostic check, use the monitor that supports both NTSC
and PAL modes

This section describes procedures and instructions necessary for
adjusting electrical circuits in this set.

Instruments required:
1) Color monitor TV
2) Oscilloscope 1 or 2 phenomena, band width over 100 MHz,

with delay mode

3) Frequency counter (over 8 digits)
4) Digital voltmeter
5) Standard commander

 * RM-SS300 (1-418-838-11)

6) DVD reference disc

HLX-501 (J-6090-071-A) (dual layer)
HLX-503 (J-6090-069-A) (single layer)
HLX-504 (J-6090-088-A) (single layer)
HLX-505 (J-6090-089-A) (dual layer)

7) SACD reference disc

HLXA-509 (J-6090-090-A)

* Use only the designated remote control when adjusting this

system component.

1. Video Level Adjustment (DVD BOARD)
<Purpose>
This adjustment is made to satisfy the NTSC standard, and if not
adjusted correctly, the brightness will be too large or small.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

LINE OUT (VIDEO) connector
(75 

Ω 

terminated)

Instrument

Oscilloscope

Adjusting element

RV401

Specification

1.0 ± 0.02 Vp-p

Adjusting method:
1) Set so that color bars are generated.
2) Adjust the RV401 to attain 1.0 ± 0.02 Vp-p.

2. S-terminal Output Check (DVD BOARD)
<Purpose>
Check S-terminal video output.  If it is incorrect, pictures will not
be displayed correctly in spite of connection to the TV with a S-
terminal cable.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

S VIDEO OUT (S-Y) connector
(75 

Ω 

terminated)

Instrument

Oscilloscope

Specification

1.0 ± 0.1 Vp-p

Checking method:
1) Set so that color bars are generated.
2) Confirm that the S-Y level is 1.0 ± 0.1 Vp-p.

1.0 ± 0.02 Vp-p

1.0 ± 0.1 Vp-p

27

3. Checking S Video Output S-C (DVD BOARD)
<Purpose>
This checks whether the S-C satisfies the NTSC Standard.  If it is
not correct, the colors will be too dark or light.

Mode

Video level adjustment in test mode

Signal

Color bars

Test point

CN005 pin 6

Instrument

Oscilloscope

Specification

286 ± 50 mVp-p

Checking method:
1) Confirm that the S-C burst is 286 ± 50 mVp-p.

286 ± 50 mVp-p

5

6

100

µ

F

75

Ω

±

1%

100k

±

1%

CN005

+

Oscilloscope

1

2

7

6

CN005

RV401

VIDEO LEVEL ADJ

28

DISP board

FFC board

 AMP board 

VIDEO board

S-VIDEO board

V-CONNECT board

REG  board

PS  board

MAIN board

STBY  board

DVD board

THERMO board

TK board

INT/COUNT SW board

IN SW board

OUT SW board

LOAD MOTOR board

CONNECTOR board

SENSOR 2 board

SENSOR board

CLAMP MOTOR board