Sony SAVA-700 / SS-T100 Service Manual ▷ View online
5
Note:
Follow the disassembly procedure in the numerical order given.
SECTION 3
DISASSEMBLY
AMPLIFIER SECTION
2
grille frame (A)
ass’y
ass’y
3
screw
(BVTT4
(BVTT4
×
25)
6
screw
(BVTT4
(BVTT4
×
25)
4
washer
(BF)
5
washer
(S)
L-ch speaker section
7
flat wire
(CN503)
(CN503)
8
connector
(CN907)
(CN907)
1
grille frame (B) ass’y
!º
five screws
(BVTP3
(BVTP3
×
8)
!™
connector
!£
Remove the amplifier
section in arrow
section in arrow
B
direction.
!¡
Remove the panel (L/B)
in arrow
in arrow
A
direction.
9
eleven screws
(4
(4
×
20)
B
A
6
SERVICE POSITION
2
two screws
(transistor)
(transistor)
!¡
eleven screws
(BVTP3
(BVTP3
×
8)
5
heatsink and
AMP board
AMP board
7
bracket
6
two screws
(BVTP3
(BVTP3
×
8)
8
connector
6
screw
(BVTP3
(BVTP3
×
8)
4
two connectors
(CN601, 603)
(CN601, 603)
!º
connector
!™
back panel (L/A)
3
two screws
(BVTP3
(BVTP3
×
8)
9
cord bushing
1
Remove the amplifier section. (Refer to page 5)
!£
two screws
(BVTP3
(BVTP3
×
8)
!¢
two screws
(BVTP3
(BVTP3
×
8)
A
!∞
Erect the Main board
in arrow
in arrow
A
direction.
!¢
two screws
(BVTP3
(BVTP3
×
8)
!¢
four screws
(BVTP3
(BVTP3
×
8)
7
bracket
MAIN board
!§
Insert an insulation sheet
between chassis and
MAIN board.
between chassis and
MAIN board.
!ª
Connect the fan motor lead wire
to MAIN board connector (CN301).
to MAIN board connector (CN301).
heatsink
!•
Insert two connectors
(CN601, 603) into
the connectors
(CN301, 911) on
the MAIN board.
(CN601, 603) into
the connectors
(CN301, 911) on
the MAIN board.
!¶
Attach the bracket
to the heatsink
with two screws.
to the heatsink
with two screws.
chassis
@º
Connect the power SW
lead wire to STANDBY
board connector (CN907).
lead wire to STANDBY
board connector (CN907).
@¡
Connect the flat wire to
DISPLAY board connector (CN503).
DISPLAY board connector (CN503).
@£
Push the power SW.
@™
Connect the MAIN board
and chassis with
two clip wires.
and chassis with
two clip wires.
8
SECTION 4
TEST MODE
This set provides four test modes as follows.
1. INPUT CHECK MODE
2. KEY CHECK MODE
3. AMP CHECK MODE
4. DEMONSTRATION MODE
The following describes each test mode in detail.
1. INPUT CHECK MODE
2. KEY CHECK MODE
3. AMP CHECK MODE
4. DEMONSTRATION MODE
The following describes each test mode in detail.
4-1.
INPUT CHECK MODE
Procedure:
1. While pressing the both
1. While pressing the both
[S.WOOFER]
and
[MASTER VOL +]
buttons, turn the power ON.
2. Fluorescent indicator tube display “SAVA-700”, after the all lights up, and enter the input check mode.
3. Pressing the
3. Pressing the
[INPUT]
button varies the display as follows.
SAVA-700
*********
S.WOOFER
*1
S.WOOFER check mode (5.1CH INPUT check mode)
AUX
AUX input (SURROUND OFF) check mode
VIDEO
VIDEO input (SURROUND OFF) check mode
TV
TV input (SURROUND OFF) check mode
AUTO POWER
AUTO POWER ON/OFF check mode
*1 Pressing the
[SURROUND]
button makes the S.WOOFER level minimum, or the
[S.WOOFER]
button makes the S.WOOFER level
maximum, or
[CENTER MODE]
button returns default.
Note:
In each mode, the volume is muted except for the channels that can be checked.
4. To release the test mode, push back
[ ]
button.
4-2.
KEY CHECK MODE
Procedure:
1. Push back
1. Push back
[ ]
button to turn the power OFF.
2. Connect the lead wire to TP3 and TP4 on the KEY board.
3. Push
3. Push
[ ]
button to power ON.
4. Let the lead wire short TP3 and TP4.
5. Fluorescent indicator tube display “KEY CHK 700” , and enter the key check mode.
6. Pressing any buttons, the number of button will be displayed on the fluorescent indicator tube.
7. Pressing the first button turns on the
5. Fluorescent indicator tube display “KEY CHK 700” , and enter the key check mode.
6. Pressing any buttons, the number of button will be displayed on the fluorescent indicator tube.
7. Pressing the first button turns on the
[READY]
LED (red), and the second button turns on the
[ON]
LED (green). Thus, two LEDs light
up alternately each time the buttons are pressed.
8. After all buttons are pressed, it will be in the STANDBY mode.
Note:
If a check failed, the set does not go in STANDBY mode, and you cannot exit from the test mode. In this case, quit the test mode by pushing back
[ ]
button.
Button
INPUT
SURROUND
CENTER MODE
WOOFER
MASTER VOL –
MASTER VOL +
Button Number
1
2
3
4
5
6
U
U
U
U
Click on the first or last page to see other SAVA-700 / SS-T100 service manuals if exist.