Sony SA-FW2010 / SA-W2010 / SS-F2010 Service Manual ▷ View online
SA-FW2010/W2010/SS-F2010
5
2-2. REAR PANEL BLOCK
Note:
Work after laying the set sideways.
5
4 Raise the rear panel block a little by little
from bottom to top of the set.
eight bosses
bottom side
2 Insert a flat-head screwdriver into a recess
in the bottom of the set
to raise the rear panel block a little.
6 rear panel block
1 four screws
(3.5
u 14)
3 Insert the jig (Part No. J-2501-238-A) into
a space made by inserting the screwdriver,
and raise the front panel block gradually.
3 Insert the jig (Part No. J-2501-238-A) into
a space made by inserting the screwdriver,
and raise the front panel block gradually.
SA-FW2010/W2010/SS-F2010
6
2-3. MAIN BOARD
Note:
This illustration sees the front panel block from rear side.
2-4. REAR CHASSIS BLOCK
Note:
This illustration sees the set from rear side.
1 eight screws
(BVTP3
u 8)
7 five screws
(BVTP3
u 8)
8 wire (flat type) (11 core)
(CN001)
9 flat type wire (31 core)
(with sheet) (CN004)
0 MAIN board
2 center panel
3 three packing sheets (D)
4 JACK board block
5 VOL knob
6 nut
1 screw
(BVTP3
u 10)
5 CN902 (2P)
6 rear chassis block
2 screw
(BVTP3
u 10)
4 five screws
(BVTT3
u 6)
3 seven screws
(BVTT3
u 6)
SA-FW2010/W2010/SS-F2010
7
2-5. AMP BOARD
Note:
This illustration sees the set from rear side.
2-6. POWER BOARD
Note:
This illustration sees the set from rear side.
5 CN553 (2P)
6 CN904 (4P)
7 CN906 (13P)
4 CN103 (8P)
qa AMP board
9 heat sink (A)
3 flat type wire (31 core)
(CN501)
0 four screws
(BVTT3
u 6)
8 three screws
(BVTT3
u 8)
1 INPUT board
(CN102)
2 TERMINAL board
(CN592)
6 CN906 (13P)
3 CN904 (4P)
7 six screws
(BVTT3
u 6)
4 screw
(BVTT3
u 6)
1 screw
(BVTT3
u 6)
2 clamp
5 clamp
9 fuse
0 fuse label
8 POWER board
Note: When the complete AMP board is replaced, spread the compound referring to
“NOTE OF REPLACING THE IC501 AND IC551 ON THE AMP BOARD AND
THE COMPLETE AMP BOARD” on servicing notes (page 3).
THE COMPLETE AMP BOARD” on servicing notes (page 3).
SA-FW2010/W2010/SS-F2010
8
2-7. FRONT PANEL ASSY, DUCT PANEL ASSY
1 Insert the jig (J-2501-238-A) into a space
and raise the front panel assy gradually.
Note: When using a jig, please work so as not to injure
front panel and speaker cabinet.
3 Insert the jig (J-2501-238-A) into a space
and raise the duct panel assy gradually.
Note: When using a jig, please work
so as not to injure duct panel assy
and speaker cabinet.
3 Insert the jig (J-2501-238-A) into a space
and raise the duct panel assy gradually.
Note: When using a jig, please work
so as not to injure duct panel assy
and
speaker
cabinet.
six bosses
twelve bosses
2 front panel assy
4 duct panel assy
Click on the first or last page to see other SA-FW2010 / SA-W2010 / SS-F2010 service manuals if exist.