Sony NWZ-F804 / NWZ-F805 / NWZ-F805N / NWZ-F806N Service Manual ▷ View online
NWZ-F804/F805/F805N/F806/F806N
13
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
2-2. CAP BLOCK
SET
2-3. CASE
BLOCK
(Page
14)
2-4. 5PIN HP ASSY (HPJ1)
(Page
(Page
15)
2-5. SPEAKER
ASSY
(SP1)
(Page
15)
2-6. MAIN
BOARD-1
(Page
16)
2-7. MAIN
BOARD-2
(Page
17)
2-10. CHASSIS (SUB) BLOCK
(Page
(Page
19)
2-11. LCD MODULE (LCD1)
(Page
(Page
20)
2-12. WINDOW ASSY (TPM1)
(Page
(Page
20)
2-8. BATTERY
ASSY
(BAT1)
(Page
18)
2-9. SUPPORT
(MID)
(Page
18)
2-2. CAP
BLOCK
(Page
13)
3 cap block
– Top rear side view –
boss
adhesive sheet (cap)
2 Remove the cap block in the direction of an arrow.
Note 2: When remove the cap block, be careful not to damage boss.
1 Peel off the adhesive sheet (cap) this position.
Note 1: When peel off the adhesive sheet (cap),
please work so as not to injure case side.
NWZ-F804/F805/F805N/F806/F806N
14
2-3. CASE BLOCK
1 two screws
(P1.4
u 5)
4 Remove the case block in
the direction of an arrow.
6 case block
5 Draw out the HP jack
from case hole.
– Top rear side view –
2 screw
(P2
1.4
u 3)
2 screw
(P2
1.4
u 3)
3 screw
(P1.4
u 1.6)
NWZ-F804/F805/F805N/F806/F806N
15
2-5. SPEAKER ASSY (SP1)
2-4. 5PIN HP ASSY (HPJ1)
– Bottom rear side view –
– 5pin HP assy front side view –
3 holder adhesive sheet
holder adhesive sheet
2 HP flexible board
(CN1001)
4 5pin HP assy
(HPJ1)
5pin HP assy
(HPJ1)
(HPJ1)
Holder adhesive sheet setting
guide line
1 Open the connector
– Bottom rear side view –
1 screw
(P2
1.4
u 6.5)
shaft
shaft
2 speaker assy (SP1)
Note: When installing the speaker assy (SP1),
match the position of two holes and two shafts.
hole
hole
NWZ-F804/F805/F805N/F806/F806N
16
2-6. MAIN BOARD-1
guide line
MAIN board
3 sheet (cover)
sheet (cover)
5 touch panel flexible board
(CN7101)
touch panel flexible board
6 cover PWB sheet
cover PWB sheet
&RYHU3:%VKHHWVHWWLQJ
MAIN board
6KHHWFRYHUVHWWLQJ
guide line
2 Remove three solders of battery wire.
Note 2: When the battery assy (BAT1) is removed, refer to “ABOUT THE
HANDLING OF THE BATTERY ASSY (BAT1)” and “ABOUT THE
REPAIRING OF THE BATTERY ASSY (BAT1)” (page 4).
1 kapton sheet (PWB)
battery assy (BAT1)
guide line
MAIN board
kapton sheet (PWB)
black
white
red
%DWWHU\ZLUHVHWWLQJ
4 Open the connector
Note 3: Insert the red wire into the gap between
the battery assy (BAT1) and MAIN board.
NG
OK
Note 4: When installing the touch panel
flexible board, make sure that has
been inserted straight.
straight slanting
–%RWWRPUHDUVLGHYLHZ–
Note 1: When the MAIN board is replaced, refer to “NOTE THE MAIN BOARD REPLACING” (page 4) and “DESTINATION SETTING” (page 5).
Click on the first or last page to see other NWZ-F804 / NWZ-F805 / NWZ-F805N / NWZ-F806N service manuals if exist.