Sony NWZ-E573 / NWZ-E574 / NWZ-E575 Service Manual ▷ View online
NWZ-E573/E574/E575
13
2-8. VOL FPC ASSY (VOF1)
5
VOL flexible board (CN2101)
6
VOL FPC assy
(VOF1)
2
sheet (FPC)
rib
hole
rib
2
sheet (FPC)
3
Peel off the adhesive shhet.
4
sheet (BT)
3DVWLQJSRVLWLRQRIVKHHW%7
Insert is straight to the interior.
Insert is incline.
NG
OK
NG
OK
NG
OK
1
cushion (NAND)
EMMC board
VOL FPC assy (VOF1)
guide line
guide line
sheet (BT)
sheet (BT)
Cover chassis
No cover chassis
3DVWLQJSRVLWLRQRIFXVKLRQ1$1'
cushion
(NAND)
(NAND)
–5HDUERWWRPVLGHYLHZ–
–)URQWERWWRPVLGHYLHZ–
hole
VOL FPC assy (VOF1) is attached surely.
VOL FPC assy (VOF1) is floating.
Note 2: When you install the VOL flexible board, please install them correctly.
There is a possibility that this machine damages when not correctly installing it.
Note 1: When installing the VOL FPC
assy (VOF1), match two holes
and two ribs.
Press and paste firmly.
battery assy (BAT1)
sheet (FPC)
MOTHER board
3DVWLQJSRVLWLRQRIVKHHW)3&
3DVWLQJSRVLWLRQRIVKHHW)3&
sheet (FPC)
VOL FPC assy (VOF1)
VOL FPC assy (VOF1)
guide
line
line
guide line
NWZ-E573/E574/E575
14
2-9. SUPPORT M
2 two claws
3 claw
4 support M
1 Lift wires of battery assy (BAT1).
– Rear bottom side view –
LCD assy flexible board
Battery wire under the rib.
Battery wire on the rib.
support (M)
%atter\ wire settiQJ
battery wire
OK
NG
Note: When you install the support M,
raise the LCD assy flexible board.
NWZ-E573/E574/E575
15
2-10. BATTERY ASSY (BAT1)
4 adhesive sheet (BATT)
3 Remove two solders of battery wire.
Note 3: When the battery assy (BAT1) is removed,
refer to “ABOUT THE HANDLING OF
THE BATTERY ASSY (BAT1)” (page 3).
sheet (PWB)
guide line
MOTHER board
3DVWLQJSRVLWLRQRIVKHHW3:%
–5HDUERWWRPVLGHYLHZ–
battery wire
MOTHER board
red
gap
black
%DWWHU\ZLUHVHWWLQJ
OK
NG
5 battery assy
(BAT1)
2 sheet
(PWB)
1 Remove the LCD assy flexible board in the
direction of arrow
A.
A
Note 1: There is a possibility of damaging LCD assy flexible board when
removing excluding the direction of arrow
A.
Note 2: Please match the position of two ditches
and two ribs when you install LCD assy
flexible
board.
If putting into the connector shift ditch
and rib, connector will be broken.
guide line
Arrange out battery wire outside.
battery assy
(BAT1)
(BAT1)
%DWWHU\DVV\%$7VHWWLQJ
two ribs
two ditches
OK
NG
NG
NWZ-E573/E574/E575
16
2-11. 5PIN HP ASSY
1 HP flexible board
(CN1401)
7 5pin HP assy
(HPJ1)
6 adhesive sheet
(CF)
5 support HP
3 claw
2
screw (M1.4)
OK
NG
– Rear bottom side view –
MOTHER board
Fully inserted
Fully inserted
Not fully inserted/
Slanting
Slanting
MOTHER board
OK
NG
Note 1: When you install the HP flexible board, please install them
correctly. There is a possibility that this machine damages
when not correctly installing it.
Note 2: When you install the 5pin HP assy block, push fully.
4
Remove the 5pin HP assy block
in the direction of an arrow.
5pin HP assy block
chassis main
Not fully inserted
chassis main
5pin HP assy block
2-12. CHASSIS (COVER) BLOCK
Note 1: There is combination in the chassis (cover) block and the chassis main block.
For details, refer to “EXPLODED VIEWS” on page 32 and 33.
4 chassis (cover) block
3 two bosses
3 two bosses
2
screw
(M1.4)
2
screw
(M1.4)
1
side spacer
1
side spacer
– Front bottom side view –
OK
NG
Screw hole is matched.
Screw hole is not matched.
Note 2: When installing the chassis (cover) block,
check that the position of a screw hole is right.
Click on the first or last page to see other NWZ-E573 / NWZ-E574 / NWZ-E575 service manuals if exist.